Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for FlightScope MEVO+
Summary of Contents for FlightScope MEVO+
- Page 1 Mevo+ User Manual Performance data you can trust...
- Page 2 Performance data you can trust “FlightScope technology is developed to offer you performance data you can trust in your pursuit of excellence.” Henri Johnson - Founder & CEO...
-
Page 3: Table Of Contents
Contents Battery Warning Setup Performance tracking Setback In the box Aiming Mevo+ Clearance Tips Battery isolation tab Charging Indoor ball spin Battery and charging indicators Aluminum sticker alignment System indicators Switch off Electronic noise Get the app Connect to Mevo+ Care Using QR Code Avoid... -
Page 4: Battery Warning
Battery Warning CAUTION: This device contains a Li-ion battery. Do not expose to temperatures below freezing point. Do not expose to excessive heat. Avoid physical impact, puncture, crushing or dropping. If the unit is struck by a club or ball, a short circuit or other heat reaction may occur, resulting in a fire. Do not tamper with the battery pack. -
Page 5: Performance Tracking
Visit MyFlightScope.com to analyze and track your data performance over time. myFlightScope.com Join the MyFlightScope.com community and connect with fellow golfers FlightScope users. Keep track of your stats over time, spot trends or tendencies and monitor how you have improved. -
Page 6: In The Box
In the box Mevo+ Case (Not to scale) Simulator angle Quickstart guide Power adapter USB charging cable Aluminum stickers (Only needed for indoor use) -
Page 7: Mevo
Mevo+ Indicator lights USB charging port Camera On/Off button Kickstand Battery and USB port (under rubber band) -
Page 8: Battery Isolation Tab
Battery isolation tab Before using, the battery isolation tab must be removed completely. If the rubber band is misaligned after the tab has been removed, gently press rubber into the groove. Pull firmly to remove. -
Page 9: Charging
Power and charging 3-4hrs for a full charge using the supplied adapter. enough for 1½ session 100% 3500mAh If the unit is unable to charge please contact support at support@flightscopemevo.com... - Page 10 Battery and charging indicators Charging error (Battery too hot or cold to charge, or battery is not connected properly) Battery Powered Charging 0-25% above 75% 25-50% above 50% above 25% 50-75% 75-100% above 10% Full under 10%...
-
Page 11: Battery And Charging Indicators
Externally Powered External & battery power (Battery not charging) (External power is not sufficient to power system) 0-25% 0-25% 25-50% 25-50% 50-75% 50-75% 75-100% 75-100%... -
Page 12: System Indicators
System indicators Radar Status Power on, switching on Processor start up 30-60 seconds Standby mode Connection Status Armed, ready to measure Ready Triggered Connected Sleep Communication Error Processor shut down 15-30 seconds Battery empty Firmware error... -
Page 13: Get The App
Get the app Download and install the FS Golf app. Scan the QR code on the bottom of the box The app download will begin automatically. If not, you will be directed to a simple selection process. -
Page 14: Connect To Mevo
Connect to Mevo+ (using QR code) Press and hold until the unit beeps Wi-Fi on Switch on Launch FS Golf app The username and password you setup will be the same for myflightscope.com... - Page 15 Connected In app, scan QR code on back of unit...
-
Page 16: Via Wi-Fi
Connect manually (via Wi-Fi) If you are unable to connect using the QR code, then you can connect manually in your device settings. Follow these easy steps: Make sure your phone’s Wi-Fi is turned on. Press the on/off button on the unit, the system and battery lights will come on. The connection light will be solid blue while the unit is ready for connection. -
Page 17: Kickstand
Kickstand Do not over extend the kickstand or force it past it’s open position, Open the kickstand and adjust the tilt using the simulator angle. this can cause damage to your unit. Using the simulator angle, adjust the kickstand to the correct tilt of 12°. Between 11°... -
Page 18: Setup
Setup - Setback OUTDOOR INDOOR SHORT INDOOR Aluminum stickers NOT required Aluminum stickers required Aluminum stickers required Unrestricted ball flight 13’ (4m) min. 8’ (2.4m) min. 7’-8’ (2.1m-2.4m) 8’ (2.4m) 8’ (2.4m) sensor to tee sensor to tee sensor to tee... -
Page 19: Aiming
Aiming Place the Mevo+ behind the ball position so that the In the App, follow the instructions using the camera view to align. camera aims along the chosen target line. Adjust the position and aim so that the vertical line on the camera view passes through the ball and is aligned with the target. -
Page 20: Clearance
Clearance Keep area between Mevo+ and the ball position clear of any objects and people. KEEP CLEAR... -
Page 21: Tips
Tips Best practice is to keep the unit on the floor with a level surface between the unit and the mat. Hitting surface Ground surface Maximum difference allowed: 3’’ (76mm) - Page 22 For putting, keep the ball and unit on an even flat surface. For putting, chipping and hitting never raise the Mevo+ to match the hitting surface, if the surface between the ball and the unit is lower.
- Page 23 Extremely low and wide shots, and shots where the player is between the Mevo+ and the ball, might not register.
-
Page 24: Indoor Ball Spin
Indoor ball spin For the best spin accuracy indoors, place an aluminum sticker on the ball. Aluminum stickers are not reqired if using the Titleist RCT ball. Aluminum stickers are for indoor use only. To order additional stickers: go to www.flightscopemevo.com... -
Page 25: Aluminum Sticker Alignment
Aluminum sticker alignment Place the ball so that the aluminum sticker faces forward, directly away from the Mevo+. Sticker facing towards target... -
Page 26: Switch Off
Switch off Press and hold to turn off, unit will beep to confirm. When all indicators are off, the unit is off. -
Page 27: Electronic Noise
Electronic noise Mevo+ is designed to operate in most environments. However certain appliances and equipment can create noise that can interfere with resulting data capture. Some common noisy objects are: aircon fluorescent fans tv’s, laptops and fridges signal lights towers desktop computers in front of the Mevo+... - Page 28 Keep area clear of possible noise interference. Make sure to move noisy electronic devices behind the unit.
- Page 29 Noisy electronic devices in front of the unit may cause poor tracking performance. Fluorescent...
-
Page 30: Care
Care Clean with a damp cloth and light Store in the case household detergent *Case not to scale... -
Page 31: Avoid
Avoid Flames and Moisture, including rain direct heat Excessive weight loading Physical impact Solvent Chemicals Water immersion... -
Page 32: Faq's And Support
Can the built in camera be used for video? The built in camera is primarily used for patented FlightScope Fusion Tracking and target alignment, and can also do video capturing. How long is the battery life? - Page 33 If you need assistance please email our support team at support@flightscopemevo.com...
-
Page 34: Technical Specifications
Technical specifications transceiver *operating frequency 24.08 - 24.16 GHz (nominal) output power (EIRP) 24dBm +/- 3dBm USA 17dBm +/-3dBm EU * Other frequencie ranges may apply in certain countries electrical, physical, and general operating temperature 0°C to 40°C / 32°F to 100°F dimensions 6.8"... - Page 35 172mm 32mm 118mm...
- Page 36 — Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by FlightScope (PTY) could void the user’s authority to operate the equipment. ISED Statement: This device contains licence-exempt transmitters(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
- Page 37 Performance data you can trust flightscopemevo.com myflightscope.com...