Page 1
This page to be removed for digital version! PART NUMBER: E47-BN276-Iss2.1 PAGE SIZE: 150x100mm COLOUR: CMYK LAYOUT: Following Sheets: - Front Cover - Henri Johnson Statement - FCC Statement - Contents - Pg 1, 2, 3 up to last page - Back Cover...
Page 2
Mevo+ User Manual Performance data you can trust @flightscopegolf...
Page 3
“FlightScope technology is developed to offer you performance data you can trust in your pursuit of excellence.” Henri Johnson - Founder & CEO...
Page 4
— Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by FlightScope (PTY) could void the user’s authority to operate the equipment. ISED Statement: This device contains licence-exempt transmitters(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Contents Performance tracking Setup In the box Setback Mevo+ Aiming Battery isolation tab Clearance Tips Charging Battery indicators Indoor ball spin System indicators Tee the ball Get the app Switch off Electronic noise Connect to Mevo+ Easy method Care Manually (alternate method) Avoid Kickstand FAQ’s and support...
Practice with any FlightScope app and get instant feedback on your ball flight and swing, or challenge your friends and compete for a spot on our leaderboards.
In the box Mevo+ Case Simulator angle* Quickstart guide Power adapter USB charging cable Wi-Fi adaptor** (fitted) Reflective stickers*** Battery (fitted) Cleaning cloth Only for simulator setup. Wi-Fi adapter for connectivity. Only needed for indoor use.
Battery isolation tab Before using, the battery isolation tab must be removed completely. If the rubber band is misaligned after the tab has been removed, gently press rubber into the groove. Pull firmly to remove.
Charging 3-4hrs for a full charge using the supplied adapter. enough for 1½ session 100% 3500mAh Connect to PC laptop, up If the unit is unable to charge please contact to 12hrs for a full charge. support at support@flightscopemevo.com...
System indicators Radar Status System off Power on, switching on Connection Status Processor start up 30-60 seconds Standby mode Ready Armed, ready to measure Connected Processor shut down 15-30 seconds Battery empty Error...
Get the app Download and install the FS Golf app. Scan the QR code on the bottom of the box The app download will begin automatically. If not, you will be directed to a simple selection process.
Connect to Mevo+ (easy method) Press and hold until the unit beeps Wi-Fi on Switch on Launch FS Golf app The username and password you setup will be the same for myflightscope.com...
Page 15
Connected In app, scan QR code on back of unit...
Connect manually (alternate method) If you are unable to connect using the QR code, then you can connect manually in your device settings. Follow these easy steps: Make sure your phone’s Wi-Fi is turned on. Press the on/off button on the unit, the system and battery lights will come on. The connection light will be solid blue while the unit is ready for connection.
Kickstand Do not over extend the kickstand or force it past it’s open position, this can cause damage to your unit. Open the Kickstand before placing. Kickstand will stop at open position. With kickstand open, the radar will be at the correct tilt angle on a flat surface.
Setup - Setback OUTDOOR INDOOR SHORT INDOOR Metallic dots required Metallic dots required Unrestricted 13’ (4m) min. 8’ (2.4m) min. 8’ (2.4m) 8’ (2.4m) 7’-9’ (2.1m-2.7m) sensor to tee sensor to tee sensor to tee...
Aiming Place the Mevo+ behind the ball position so that the In the App, follow the instructions using the camera view to align. camera aims along the chosen target line. Adjust the position and aim so that the vertical line on the camera view passes through the ball and is aligned with the target.
Indoor ball spin For the best spin accuracy indoors, place a reflective sticker on the ball. Reflective stickers are for indoor use only. To order additional stickers: go to flightscope/product-category/accessories...
Electronic noise Mevo+ is designed to operate in most environments. However certain appliances and equipment can create noise that can interfere with resulting shots. Some common noisy objects are: aircon fluorescent fans tv’s, laptops & fridges signal lights towers desktop computers in front of the Mevo+...
Page 27
Keep area clear of possible noise interference. Make sure to move noisy electronic devices behind the unit.
Page 28
Noisy electronic devices in front of the unit may cause poor tracking performance. Flourescent...
FAQ’s and support Below are the top 5 frequently asked questions. For more FAQ’s please refer to flightscopemevo.com/faq 1. Can Mevo+ be used indoors and outdoors? Yes. Please check page 13 for indoor space requirements. 2. Does a reflective sticker need to be used? Yes, for indoor use only.
Page 32
We recommend you browse the FAQ’s on the website or check out the mevo chat forum before submitting a support question to the MEVO team. If you need assistance please email our support team at support@flightscopemevo.com...
Technical specifications transceiver *operating frequency 24.08 - 24.16 GHz (nominal) output power (EIRP) 24dBm +/- 3dBm USA 17dBm +/-3dBm EU * Other frequencies ranges may apply in certain countries electrical, physical, and general operating temperature 0°C to 40°C / 32°F to 100°F dimensions 6.8"...
Page 34
Performance data you can trust flightscopemevo.com myflightscope.com...