Related Manuals for KANSAI SPECIAL DFB MR-S Series
Summary of Contents for KANSAI SPECIAL DFB MR-S Series
- Page 1 PARTS LIST & INSTRUCTION Industrial Sewing Machines First published : June 2020 No. 200057...
- Page 11 INDEX 1 REF. PART NO. REF. PART NO. REF. PART NO. REF. PART NO. MEMO 品 番 品 番 品 番 品 番 02-01 01-816 02-45 27-123 03-14 75-244 02-36 87-010 06-01 06-003 05-08 27-343 01-26 75-329 03-24 87-019 06-02 06-186 03-04 27-471 03-15 75-332 06-28 87-104...
- Page 12 MR-S Series Instruction Manual First published : June 2020...
-
Page 13: Table Of Contents
INTRODUCTION 1-1 Stitch type ························································································· 2 2. NEEDLES & THREADING THE MACHINE Thank you for your purchasing Kansai Special's DFB/MR-S Series. 2-1 Needles ····························································································· 2 2-2 Replacing the needle ··········································································· 2 Read and study this instruction manual carefully before beginning any of the 2-3 To thread the machine ·········································································... -
Page 14: Specifications
2-3 To thread the machine 【1】SPECIFICATIONS Thread the machine correctly by referring to pages 3 to 4. Incorrect threading may cause skip stitching, thread breakage and/or uneven stitch 1-1 Stitch type formation. When threading the looper, tilt the looper holder toward the front of the JIS401 double chain stitch machines machine using the looper drawing bar. -
Page 15: Machine Speed
【3】MACHINE SPEED ■ Threading diagram for DFB1404 3-1 Machine speed & direction in which the machine pulley runs Refer to the table below for maximum and standard speeds of the Series. extend machine life, machine approximately 15~20% below the maximum speed for the first 200 hours of operation (approx. -
Page 16: Sewing Machine Installation
【 4】 SEWING MACHINE INSTALLATION ■For direct motor 4-1 Cutting the machine table ■For clutch motor MR-S MR-S... -
Page 17: Mr-S Adjustment
5-3 Timing of ruffling arm (Fig. 6) 【 5】 MR-S ADJUSTMENT Fig.1 Correct timing is when the ruffling blade reaches nearest Fig.6 5-1 Adjustment of bottom stripper blade (Fig.1) to the needle, the needle start stitching into the fabric. For the adjustment of bottom stripper blade “A”, Open top cover and change the timing pulley position by please follow the picture in the right. -
Page 18: Cleaning The Machine
【 6】 CLEANING THE MACHINE At the end of each day, remove the presser foot and the needle plate and then clean the slots of the needle plate and the area around the feed dogs. MR-S... - Page 19 MORIMOTO MFG. CO., LTD. 1-4-17, SUNA, SHIJONAWATE-CITY, OSAKA 575-0001, JAPAN TEL: +81-72-877-1221 FAX: +81-72-878-9649 E-MAIL: hqeigyo@kansai-special.com URL:www.kansai-special.com FOREIGN AFFILIATED COMPANIES KANSAI SPECIAL AMERICAN MACHINE CORP. 476 HAMPSHIRE DR., GAFFNEY, SC 29341. USA E-MAIL: ksam@kansaispecial.net KANSAI SPECIAL EUROPE GMBH QUIRINSTR. 19, 40545 DUSSELDORF, GERMANY TEL: +49-211-577-9090 FAX: +49-211-558-1477 E-MAIL: contact@kansai-special.de...