Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for A.O. Smith TE-35
Summary of Contents for A.O. Smith TE-35
- Page 1 Tankless Electric Water Heater User Manual...
-
Page 2: Table Of Contents
Contents General Information ............... 1 Safety Instructions . -
Page 3: General Information
General Information On Receipt It is our policy to promote safe delivery of all orders. This product shipment has been thoroughly Visible Loss or Damage If any of the goods called for on the bill of lading or express receipt are damaged or the quantity is short, do not accept them until the freight or express delivery agent makes an appropriate notation on your freight bill or receipt. -
Page 4: Safety Instructions
Safety Instructions The safety of you and your loved ones is paramount. There are several safety related messages in this manual, which have been provided during various steps such as the installation, operation and maintenance of your Water Heater. These messages point out potential hazards and also educate on how to reduce any potential risks. - Page 5 TE-35 TE-55 Model Power [W] 3500 5500 Voltage/Frequency [V/Hz] 230~/50 Rated Current [Amps] Required circuit breaker [Amps] Working water N/cm 2 - 60 pressure Water head (metres) 2 - 61.2 Inlet/Outlet connections [inch] ½ BSP Net Weight (kgs.) Dimensions Figure 1...
-
Page 6: Safety Precautions
Figure 2 Front view with Front view without Rear view Service cover Service cover Part Description Part Description Cold water inlet Rear cover Hot water outlet Terminal blocks LED display Cable faster Outlet Temperature sensor Triac Transformer Flow sensor Filter plate Service cover Heating chamber Mounting bracket... -
Page 7: Installation
Installation Bubble level indicator and Impact drill tool are available. Mounting the Water Heater It is recommended as per IS 302-1 to have 6 Water Heater must be located within 2 ft. inches clearance from wall. (approx.) from a 230 V power supply with Select a place to mount Water Heater in a proper grounding. - Page 8 Installation (contd...) Remove the Mounting bracket from the Insert the Expansion Anchor into the hole back side of the product. (Step 1). Mark the holes using Mounting bracket Insert the Mounting screw over the (Step 1). Expansion Anchor through the Mounting Drill 4 holes of diameter 6 mm (Step 2).
-
Page 9: Plumbing Instructions
Plumbing instructions Figure 10 Installation Diagram Cold tape Water Tap Water Tap *Flexible Hose Cold Water Tap Water Tap Upward Downward installation installation *Flexible Hoses to be procured by the customer, not part of standard product. leakage. 2. Make necessary plumbing with reference to the Installation Diagram. (Refer “Installation Diagram”) 3. -
Page 10: Operation
CAUTION Use only Nylon/ Stainless Steel (SS) braided hoses (Flexible Hoses) having a minimum pressure rating of 6 Bar and hoses should be compatible for hot water applications. Failure to follow this instruction can result in property damage. Operation 1. Open a nearby hot water faucet to permit air to escape. Figure 11 to the unit. - Page 11 CAUTION Electrical connection to the Water Heater should have circuit breaker, do not use any adapters. Use multimeter to check whether the live line and neutral line are not reverse, to ensure complete safety. meter capacity and electric supply cable of 2.5 sq. mm is used. The Water Heater should be earthed reliably.
- Page 12 Sleep mode: Sleep mode is activated when the Water Heater is in standby mode and no button is touched on Touch panel or user intervention for 15 seconds. Touch any of the buttons on the Touch panel to enable normal mode. If the heater has been paused, you may initially get a short burst of very hot water while you turn on again.
-
Page 13: Troubleshooting
Troubleshooting problem you may be experiencing. Please review this chart before calling for Customer Care Centre. Problems Possible Cause(s) Solution Inlet and outlet Fittings not tight. Rubber washer worn-out at the Replace Rubber washer at the inlet. inlet. LED display does No power supply to the heater. -
Page 14: Circuit Diagram
Error Messages and Actions Error Code Reason Self-diagnostic / Action Outlet temperature is over 65°C. Malfunction of PCB Call Customer Care Centre. Electricity leakage Call Customer Care Centre. Power cord not pass through leakage Call Customer Care Centre. sensor Malfunction of PCB Call Customer Care Centre. -
Page 15: Warranty Terms And Conditions
Warranty Terms and Conditions Product Warranty Your A. O. Smith Water Heater is warranted against defects arising from faulty design, workmanship and materials for a period of 1 year from the date of the invoice, subject to the following conditions: 1. - Page 16 Product colour and image shown may vary from the actual product.
Need help?
Do you have a question about the TE-35 and is the answer not in the manual?
Questions and answers