Related Manuals for Energizer EZ20VELC-2B
Summary of Contents for Energizer EZ20VELC-2B
- Page 1 ORIGINAL INSTRUCTIONS >EN CORDLESS PRUNING MACHINE EZ20VELC-2B USER GUIDE CAUTION: Read this manual before using this machine!
- Page 3 Let’s get started. You’re excited to power up, so we’ll keep this brief!
-
Page 4: Table Of Contents
CONTENTS SAFETY INSTRUCTIONS ..................... 5 YOUR PRODUCT ........................ 12 FUNCTIONAL DESCRIPTION ..................... 13 ASSEMBLY ......................... 14 OPERATION ........................16 MAINTENANCE AND STORAGE ..................19 TECHNICAL DETAILS ......................22 DISPOSAL ........................... 23 DECLARATION OF CONFORMITY ..................23 WARRANTY ........................24 PRODUCT FAILURE ...................... -
Page 5: Safety Instructions
1. SAFETY INSTRUCTIONS 1.1 GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool"... - Page 6 left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts.
- Page 7 batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury. f) Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130 ° C may cause explosion. g) Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions.
- Page 8 Do not attempt to fell a tree until you have an understanding of the risks and how to avoid them. Serious injury could occur to the operator or bystanders while felling a tree. Use of the chain saw for operations different This chain saw is not intended for tree felling.
- Page 9 Risk of electric shock. 3) To reduce the electric shock hazard, unplug the battery charger from the mains before cleaning the charger. 4) Do not subject the battery to strong sunlight over long periods and do not leave it on a heater. Heat damages the battery and this is risk of explosion.
- Page 10 given supervision or instruction concerning use of the charger in the safe way and understand the hazards involved. Children shall not play with the charger. Cleaning and user maintenance of the charger shall not be made by children without adult supervision. 2) If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a...
- Page 11 3) There is a risk of a short-circuit due to liquid penetrating the housing. Do not immerse the product and the accessories in water. And make sure that no water or other liquid can enter the housing. 4) Damage to your health caused by swinging your hands and arms when operating the tool for longer periods of time or if the tool is not held or maintained properly.
-
Page 12: Your Product
Do not incinerate the battery. Ambient temperature of 40° C max, only for the battery. Use the charger Indoor use only. Recycling. Fuse. 2. YOUR PRODUCT 1) Top handle 5) Guide bar 9) Lock off button 13) Carabiner or rope 2) Battery cartridge 6) Oil tank cover 10) Front handle... -
Page 13: Functional Description
3. FUNCTIONAL DESCRIPTION WARNING! Always be sure that the tool is switched off and the battery is removed before adjusting or checking function on the tool. 3.1 TOOL / BATTERY PROTECTION SYSTEM The tool is equipped with a tool/battery protection system. This system automatically cuts off power to the motor to extend tool and battery life. -
Page 14: Assembly
4. ASSEMBLY WARNING! Always be sure that the tool is switched off and the battery is removed before assembling the tool. 4.1 INSTALLING OR REMOVING SAW CHAIN WARNING! Always wear gloves when installing or removing the saw chain. Knob Sprocket cover Loosen the screw by turning counterclockwise the knob until the sprocket cover comes off. - Page 15 Hook Sprocket cover Hole Insert the hook of sprocket cover into the hole and then place the sprocket cover on the tool. Turn the knob clockwise to tighten the screw firmly. 4.2 ADJUSTING SAW CHAIN TENSION...
-
Page 16: Operation
Just a slight loosening of the screw allows the saw chain tension to be adjusted. After adjusting, retighten the screw firmly. 5. OPERATION 5.1 LUBRICATION Saw chain is automatically lubricated when the tool is in operation. Check the amount of remaining oil in the oil tank periodically. - Page 17 Bring the tip guide/lower guide into contact with the branch to be cut before switching on. Cutting without bringing the tip guide/lower guide into contact with the branch may cause the guide bar to wobble, resulting in injury to operator. Saw the wood to be cut by just moving it down.
- Page 18 If you cannot cut the timber right through with a single stroke: Apply light pressure to the handle and continue sawing and draw the chain saw back a little; then apply the spike a little lower and finish the cut by raising the handle. 5.3 CARRYING TOOL Chain cover Battery...
-
Page 19: Maintenance And Storage
6. MAINTENANCE & STORAGE 6.1 MAINTENANCE WARNING! • Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. • Always wear gloves when performing any inspection or maintenance. •... - Page 20 Guide the file as shown in the figure. After sharpening the chain, check the height of the depth gauge using the chain gauge tool (optional accessory). Remove any projecting material, however small,with a special flat file (optional accessory). Round off the front of the depth gauge again. Wash away dust and particles from saw chain after adjusting the height of depth gauge.
- Page 21 4) Replacing the sprocket Before fitting a new saw chain, check the condition of the sprocket. Sprocket Locking ring WARNING! A worn sprocket will damage a new saw chain. Have the sprocket replaced in this case. The sprocket need to be installed so that it always faces as shown in the figure. Locking ring Sprocket Washer...
-
Page 22: Technical Details
If you need any assistance for more details regarding these accessories, ask your local Service Center. • Saw chain • Guide bar • Guide bar cover • File • Tool bag WARNING! If you purchase a guide bar of different length from the standard guide bar, also purchase a suitable guide bar cover together. -
Page 23: Disposal
BUILDER SAS 32, rue Aristide Bergès - ZI 31270 Cugnaux - France, declares that, Product: Cordless PRUNING MACHINE Trade mark: ENERGIZER Model: EZ20VELC-2B Serial number: 20220513861-20220514212 Is in conformity with the essential requirements and other relevant provisions of the applicable European Directives, based on the application of European harmonized standards. -
Page 24: Warranty
10. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 25: Product Failure
11. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank if your product has one. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 26: Warranty Exclusions
12. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •...