Advertisement
Quick Links
Advertisement
Related Manuals for Garlando Toorx TRX 8500 EVO
Summary of Contents for Garlando Toorx TRX 8500 EVO
- Page 1 INSTRUCTION...
-
Page 2: Exploded Drawing
Exploded drawing... -
Page 3: Parts List
Parts list Description Description Description Base frame Incline motor Cross head sunk screw M3X8 Running board Controller Cross head sunk supporting tube screw M8X25 Incline frame Overload switch Cross head sunk screw M8X30 Left upright tube Power switch Cross head sunk screw M8X35 Right upright tube Socket... -
Page 4: Installation Instruction
Side rail Bolt M8X50 Spring washerΦ8 positioning nut Square end cap Bolt M10X50 Spring washerΦ10 Cushion Bolt M10X75 Nylon washerΦ10 Motor upper Bolt M10X90 cover Left upright tube Bolt M10X160 Wrench cover Right upright tube Cross screwdriver Half round bolt M8X20 cover Nut cap Screwdriver... - Page 5 2.1 Install Left upright tube (4) to base frame (1) by two sets of half round bolt M8X20 (A8), half round bolt M8*40 (A9) and four pcs of flat washer φ8 (C2) by side. (Attention: to align screw hole with the upper surface). Make sure the bolts to connect left upright tube and base frame.
- Page 6 5. Installation of display screen 5.1 Connect the signal wire from display screen to corresponding wire from controlling panel. Crowding the extra wire into the panel. 5.2 Connect the display screen (7) to handlebar and controlling panel (6) by four sets of half-round bolt M10X20(A10), flat washers φ10(C3).
- Page 7 running belt by hand, check whether the rotation is flexible, there is no abnormal sound. 2. Connect power, press Start key, the treadmill starts to run in low speed,observe whether belt and computer are run normally. Press the speed up and down key to observe the rotation and display of the treadmill. If the belt deviated, stop the treadmill and adjust the running belt according to the requirements of "maintenance".
-
Page 8: Console Instruction
protection of incline motor, the function will be restored automatically after 1 hour stop using. Console instruction WARNING: To reduce the possibility of electric shock, keep the console dry. To prevent liquid from spilling onto the console, only sealed water bottles can be placed on the water bottle holder. - Page 9 2.1.1 Button function Icon Name Function After power on, press “START”,the treadmill starts running. START PAUSE/STOP Press this button when running, the treadmill will puase, and press again to stop running. After the pause, press the start button and the treadmill will return to the running state before the pause.
- Page 10 There are 18 preset programs: 1-5 Physical training program; 6-10 Physical compliance training program; 11- P2: Custom and preset 12 Body fit training program ； 13-15 Physical fitness program maintaining program; 16-18 Physical recovery program. And 5 custom programs （USER1-5） This program can be set for time/distance/heat, only one P3: Manual program mode can be set at a time.
- Page 11 3.1 Illustration 3.2 Display function...
- Page 12 4. Operation instruction 4.1 Treadmill operation instruction 4.1.1Standby mode operation Put the special power wire insert to treadmill socket, another end of power wire is connected to the environment working voltage (the environment working voltage must be in conformity with requirements of the treadmill).
- Page 13 P1 Heart rate control program P2 Custom/Preset programs P3 Manual program P4 Target program P5 Hill program...
- Page 14 P6 Fat burn program P7 Cardio program P8 Strength program P9 Fit test program...
- Page 15 4.1.5 MP3 Playing and treadmill operation Warm tip: When you use P1 Heart Rate Control Program/ P6 Fat burn Program/ P7 Cardio Program, do not play MP3 at the same time to avoid audio signal interfere to wireless heart rate, and special HRC wireless heart rate chest belt will be required.
- Page 16 ● Hill program graphics ●Fat percentage reference table ●Adult body mass index(BMI) reference table...
- Page 17 5. Hand pulse test The test can detect static and dynamic heart rate before and after exercise, and recovery after exercise. The user holds the metal plate of heart rate detection on the left and right horizon handlebar with both hands, then the heart rate value will be displayed on the screen.
- Page 18 1．Clean: The surface of the treadmill should be kept clean, pull out the power cord before cleaning. You can clean the running belt and the surface of the treadmill with a soft and wet cloth, be sure not to use strong solvents.
- Page 19 Oil adding reminding replaces belt reminding...
- Page 20 GARLANDO SPA Via Regione Piemonte, 32 - Zona Industriale D1 15068 - Pozzolo Formigaro (AL) - Italy www.toorx.it - info@toorx.it...