Power/Standby Indicator; Setting The Picture To Suit The Movie; Reducing Burn-In Of The Screen - NEC PlasmaSync 42XM2 Operation Manual

POWER/STANDBY indicator

Power POWER/ Power
management STANDBY management
mode indicator operating status
On Green Not activated.
Off Red Activated.

Setting the picture to suit the movie

The film image is automatically discriminated and
projected in an image mode suited to the picture.
[NTSC, PAL, PAL60, 480I (60Hz), 525I (60Hz), 576I
(50Hz), 625I (50Hz), 1035I (60Hz), 1080I (60Hz) only]
Example: Setting the "CINEMA MODE" to "OFF"
Set "ADVANCED OSM" to "ON" in the main menu (1/
2), then perform the following operations.
1. On the MAIN MENU, select "OPTION2", then press
the MENU/ENTER button.
The "OPTION2" screen appears.
2. Use the and buttons to select "CINEMA MODE".
3. To set the CINEMA MODE to "OFF" ...
Use the and buttons to select "OFF".
The mode switches as follows each time the
button is pressed:
ON OFF
OPTION2
PREVIOUS PAGE
POWER MGT.
CINEMA MODE
LONG LIFE
GRAY LEVEL
S1/S2
NEXT PAGE
SEL. ADJ.
Information
CINEMA MODE
ON ................... Automatic discrimination of the
image and projection in cinema mode.
OFF ................... Cinema mode does not function.
Restoring the factory default settings
Select "ALL RESET" under the OPTION1 menu. Note
that this also restores other settings to the factory
defaults.
Description Turning the picture
back on
Horizontal and vertical Picture already on.
synchronizing signals
are present from the
computer.
Horizontal and/or Operate the keyboard or
vertical synchronizing mouse. The picture
signals are not sent reappears.
from the computer.
or
2 / 3
: OFF
: OFF
: 3
: OFF
EXIT RETURN

Reducing burn-in of the screen

The brightness of the screen, the position of the picture,
positive/negative mode and screen wiper are adjusted to
reduce burn-in of the screen.
Set "ADVANCED OSM" to "ON" in the main menu (1/
2), then perform the following operations.
1. On the MAIN MENU, select "OPTION2", then press
the MENU/ENTER button.
The "OPTION2" screen appears.
2. Use the and buttons to select "LONG LIFE", then
press the MENU/ENTER button.
The "LONG LIFE" screen appears.
PLE
ORBITER
INVERSE
SCREEN WIPER
SOFT FOCUS
SEL.
3. Set the LONG LIFE mode using
See page 27 to set PLE.
See page 28 to set ORBITER.
See page 28 to set INVERSE.
See page 29 to set SCREEN WIPER.
See page 30 to set SOFT FOCUS.
Information
Restoring the factory default settings
Select "ALL RESET" under the OPTION1 menu. Note
that this also restores other settings to the factory
defaults.
PLE (Peak Luminance Enhancement)
Use this to activate the brightness limiter.
Example: Setting "PLE" to "LOCK1"
Perform Steps 1-2 of LONG LIFE, then...
3. Use the and buttons to select "PLE".
4. Use the and buttons to select "LOCK1".
The mode switches as follows each time the
button is pressed:
AUTO LOCK1
PLE
ORBITER
INVERSE
SCREEN WIPER
SOFT FOCUS
SEL.
Information
PLE settings
AUTO .............. The brightness of the screen is
adjusted automatically to suit the
picture quality.
27
LONG LIFE
: AUTO
: OFF
: OFF
: OFF
: OFF
ADJ. EXIT RETURN
and buttons.
LOCK2 LOCK3
LONG LIFE
: LOCK1
: OFF
: OFF
: OFF
: OFF
ADJ. EXIT RETURN
or