Identification Of Controls; Front Panel - NAD T755 Owner's Manual

1 2 3 4 5 6
11
1 POWER BUTTON: Press this button or the HTR 3 remote's [ON] button
to switch ON the T 755. The Standby LED indicator will turn from amber
to blue and illuminate the VFD. Pressing the power button again turns
the unit back to standby mode.
The T 755 can also be switched ON from standby mode by pressing any of
the front panel buttons. When both Main and Zone 2 are ON, press and hold
this button for more than five seconds to place them at standby mode.
NOTES
• The rear panel POWER switch must be in the ON position for the Power
button to activate.
• If Auto Trigger IN at Trigger Setup menu is assigned to "Main" or "All" and
the TRIGGER switch is set to "AUTO" mode, the Power button in the front
panel as well as the corresponding ON/OFF function keys in the HTR 3
remote control will be disabled effectively handing this function to an
external controller. Switch TRIGGER to "OFF" to maintain normal power
ON/OFF function procedures. (See section also about "TRIGGER SETUP"
under the "SETUP MENU" discussions.)
2 STANDBY LED: This indicator will light up amber when the T 755 is
in standby state. When the T 755 main or zone 2 are in the ON state,
this indicator will illuminate blue. In the unlikely event that the T 755
switches to protection state, then this indicator will illuminate red.
When an infrared command from the HTR 3 is received, this indicator
will also flash momentarily.
3 INFO: Repeatedly toggle this button (press/hold first if in Tuner mode
and then toggle) to display both at the Vacuum Fluorescent Display
(VFD) and On-Screen Display (OSD) the following – Current Source,
Volume level, Listening mode, Audio Source Format, and active Zone 2
with corresponding Source Input. While at Tuner mode, toggle this
button to cycle through RDS name and RDS text.
4 AM/FM/DB: Toggle this button to select either AM, FM, DAB (Europe
version) or XM (North America version) tuner functions.
7
12 13

IDENTIFICATION OF CONTROLS

8 9
14 15 16 17
5 TUNER MODE: In FM mode, this button will toggle between FM Stereo
and FM mono. Select FM Mono (FM stereo and FM Mute icons at VFD
are extinguished) for stations that have too much interference or are
too weak. In DAB (European version only) or XM (North America version
only) radio, this button enables the digital radio menus in conjunction
with the Navigation button and Enter buttons.
6 MEMORY: Press this button to store tuned AM, FM and digital radio
stations to the T 755's 40 preset-memory locations. One can store a mix
of any AM, FM and digital radio stations to the 40 available presets.
7 NAVIGATION and ENTER buttons: These buttons are used to
navigate the T 755 OSD, Tune Forward [
Preset Forward [ ] and Preset Reverse [
DAB (European version), XM (North American version) tuner functions
and iPod. The middle round button is designated as "ENTER" button; this
is normally pressed to complete a selection, procedure, sequence or
other applicable functions.
8 VACUUM FLUORESCENT DISPLAY (VFD): Provide visual information
on all important modes of the T 755 as well as the settings and
functions for both Main and Zone 2 locations.
9 REMOTE SENSOR: Point the HTR 3 remote control at the remote sensor
and press the buttons. Do not expose the remote sensor of the T 755 to a
strong light source such as direct sunlight or illumination. If you do so, you
may not be able to operate the T 755 with the remote control.
Distance: About 23ft (7m) from the front of the remote sensor.
Angle: About 30o in each direction of the front of the remote sensor.
10 VOLUME: Use this control to adjust the volume level of the main speakers.
The default volume level is -20dB. The VOLUME knob is also used to
increment/ decrement other adjustable parameters like Tone Controls.
FRONT PANEL
10
18 19
] and Tune Backward [ ],
] as well as navigation of
7