Loading Code-Libraries; Search Mode; Checking Code-Library Number - NAD T755 Owner's Manual

OPERATION
USING THE HTR 3 REMOTE CONTROL

LOADING CODE-LIBRARIES

The HTR 3 can store a different library of default NAD codes for each of its
Device Selector "pages. " If the original default library does not control your
NAD CD player, tape deck, DVD player, or other component, follow the
procedure below to change the code-library.
Begin by ensuring that the component you wish the HTR 3 to control is
plugged in and powered-up ("on, " not merely in standby). To enter the
HTR 3s Library Mode, simultaneously press-and-hold for 3 seconds both the
desired Device Selector key and the [AVPS] key, until the Learn LED turns
green.
While keeping the HTR 3 pointed toward the component, enter the first
appropriate three-digit code-library number from the table below. Press
[OFF]. If the component turns off, press [ENTER] to accept that code-library
number and exit the Library Mode. If the component does not turn off,
enter the next three-digit code-library number from the table.
When you enter the correct number the component will turn off; press
[ENTER] to accept that code library number and exit the Library Mode.
NAD PRODUCT
LIBRARY CODE
DESCRIPTION
Receiver/Processor
100
(Discrete ON/OFF)
Receiver/Processor
101
(Toggle ON/OFF)
102 S170
103 L75
Second Zone
104
Commands
105 L70
106 L76
107 118
108 L53
109 L73
Stereo Receiver/
110
Amplifier
111 Stereo Second Zone
112 Txx5 Series
200 CD Player
201 CD Player (old)
202 5170, 5240, 5340
203 5325
204 5060
205 M5
300 Tuner

NAD PRODUCT
LIBRARY CODE
DESCRIPTION
301 L75, L76 Tuner
302 L70 Tuner
303 L53 Tuner
304 L73 Tuner
305 C425
306 C445
307 Txx5 Series Tuner
400 Tape Deck B
401 TAPE Deck A
500 TV 280
501 MR13
502 MR20
503 PMR45
T535, T562, T585,
600
M55
601 T550, L55
T512, T531, T532,
602
T571, T572
603 L70, L73 DVD
604 L56
T513, T514, T515,
605
T524, T533, T534
606 L53 DVD

SEARCH MODE

If none of the codes from the table, when entered, turns on the
component, and if you are quite sure you have followed the above
procedure completely and carefully, you may want to try the "search"
method as follows:
Enter Library Mode by simultaneously pressing-and-holding for 3 seconds
both the desired Device Selector key and the [AVPS] key, until the Learn LED
turns green. Now press-and-hold the HTR 3's [ ] or [ ]) key; the remote will
step through all the available codes at a rate of approximately 1 per second.
When the component turns off, immediately release the cursor key; press
[ENTER] to accept that code-library and exit the Library Mode. Try a few
commands; should you prove to have stepped past the needed code-
library, re-enter the Library Mode and use the cursor key to step back to it.
NOTE
It is possible that search mode will find code-libraries that operate, at
least partially, some other brand (non-NAD) components. You may
certainly exploit such capabilities as you find them. However, since we
can only ensure the completeness or accuracy of NAD code-libraries, we
cannot support the HTR 3's operation with other-brand components.

CHECKING CODE-LIBRARY NUMBER

You can check the current code-library on any Device Selector key as
follows. Enter Library Mode by simultaneously pressing-and-holding for
3 seconds both the desired component's Device Selector key and the
[AVPS] key, until the Learn LED turns green. Press the [DISP] key; the HTR 3
indicates the current code-library by flashing its [CUSTOM], [VCR], and
[MACRO] keys.
For example, to indicate code-library #501, the HTR 3 will flash [CUSTOM] 5
times, pause, and then flash [MACRO] once. You might wish to make a note
of your components' code-library numbers.
SUMMARY OF THE HTR 3 MODES
Mode
Learn/Copy/Punch Through
Delete Mode
Macro Record
Library Mode
Back Light Timeout
Factory Reset
Keys To Press (for 3 seconds)
Device Key + RES Key
Device Key + RTN Key
Macro Key + Function Key
Device Key + AVPS Key
DISP Key + Digit Key
See "Factory Reset" above