Advertisement
Quick Links
Advertisement
Related Manuals for Fortinet FortiCam OB30
Summary of Contents for Fortinet FortiCam OB30
- Page 1 FortiCam OB30 QuickStart Guide...
- Page 2 Fortinet. For absolute clarity, any such warranty will be limited to performance in the same ideal conditions as in Fortinet’s internal lab tests. Fortinet disclaims in full any covenants, representations, and guarantees pursuant hereto, whether express or implied.
-
Page 3: Table Of Contents
Table of contents Package contents Hardware installation Technical specifications Register for support Cautions and warnings Regulatory notices Fortinet Product License Agreement / EULA and Warranty Terms... -
Page 4: Package Contents
Package contents FortiCam OB30 Camera Wall mount base Quickstart guide Mounting guide Mounting accessories Silica gel Wall mount bracket Sunshield Waterproof connetors Page 1... -
Page 5: Hardware Installation
Hardware installation Before installing the camera, choose a location where the camera cannot be easily reached and where the cables can enter the wall or ceiling. An easily accessible camera and exposed wires could lead to vandalism. Caution: Do not throw away the silica gel package. To install the camera Install the wall mount base to the wall with the supplied mounting accessory kit and mounting guide. - Page 6 Run the cables through the waterproof connector. Attach the waterproof connector to the bottom of the camera and tighten the connector to the camera to secure and protect the cables. Attach the camera to the wall mount bracket. Press the push-lock button and then tightening the two screws provided.
- Page 7 Open the camera’s top cover. Connect the RJ45 cable to the Ethernet port on the MB module. Optionally connect all other cables to the MB module before proceeding to the next step. Page 4...
- Page 8 Affix the silica gel onto the inside of the camera using the attached adhesive sticker. Close the camera’s cover and ensure the clip is in the locked position. Install the sunshield and tighten the torx screw on the side cover. Note: The silica gel is inside of the silver packaging.
- Page 9 To reboot the camera Open the top cover of the camera and press the Reboot button on the MB module. To reset the camera Press and hold the Reset button on the MB module for more than 5 seconds to reset the camera to its factory default settings. Or, press and hold the Reset button for less than 5 seconds to reset all the camera settings except the network settings (IP address/netmask, gateway IP, and DNS server IP).
-
Page 10: Technical Specifications
Technical specifications Hardware Specifications Format Indoor/outdoor bullet, vandal, wall mounting 3 mega-pixel, 1/3” Progressive CMOS Sensor Type Iris F1.4, 0.1 Lux (Color), 0.06 Lux (B/W) 3x/None Optical/Digital Zoom Focal Length 3 mm–10 mm (motorized, autofocus) View Angle H: 82°–34° V: 63°–26° D: 103°–43° Smart 30m / yes IRLED / IRC Streaming Protocol... - Page 11 Dimensions Weight 4.42lbs (2005g) 263 x 161 x 406 mm (10.6 x 6.3 x 16 in) Height x Width x Length Power Power Required PoE (802.3at) 14.3W max Power Consumption (AVG) Page 8...
-
Page 12: Register For Support
Register for support Register your Fortinet product to receive: • Technical support • New product features • Protection from new threats Vous devez enregistrer le produit pour recevoir: • Support technique • Nouvelles fonctionnalitées du produit • Protection contre de nouvelles menaces La reistrazione ti permette di usufruire di: •... -
Page 13: Cautions And Warnings
Cautions and warnings Environmental Specifications Operating Temp.: -40°C ~ 60°C/-40°F ~ 140°F Refer to specific Product Model Data Sheet for Environmental Specifications (Operating Temperature, Storage Temperature, Humidity, and Altitude) Référez à la Fiche Technique de ce produit pour les caractéristiques environnementales (Température de fonctionnement, température de stockage, humidité... -
Page 14: Regulatory Notices
Regulatory notices Federal Communication Commission (FCC) – USA This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. -
Page 15: Fortinet Product License Agreement / Eula And Warranty Terms
(except as provided in section 5 (“Transfer”) and section 15 (“Open Source Software”) below), non-exclusive, revocable (in the event of your failure to comply with these terms or in the event Fortinet is not properly paid for the applicable Product) license to use the Software... - Page 16 If you are a Fortinet contracted and authorized reseller or distributor of Products, you may transfer (not rent or lease unless specifically agreed to in writing by Fortinet) the Software to one end user on a permanent basis, provided that: (i) you ensure that your customer and the end user receives a copy of this...
- Page 17 Fortinet’s functional specifications. Except as otherwise agreed by Fortinet in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by Fortinet for the Software. The Software War- ranty Period shall extend for an additional ninety (90) days after any replacement software is delivered.
- Page 18 In the event of any disputes arising out of this Agreement or Fortinet’s limited warranty, the parties submit to the jurisdiction of the federal and state courts located in Santa Clara County, California, as applicable. 9. Limitation of Liability.
- Page 19 For any Open Source Software covered under the GPL, the source code is made available on this CD or download package. If any Open Source Software licenses require that Fortinet provide rights to use, copy or modify a Open Source Software program that are broader than the rights granted in this agreement, then such rights shall take precedence over the rights and re- strictions herein.
- Page 20 a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.
- Page 21 those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
- Page 22 code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it).
- Page 23 tions of the Library will still fall under Section 6.) Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself. 6.
- Page 24 then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library.