Page 1
SERVICE MANUAL MODEL MODEL DEST. CHASSIS NO. DEST. CHASSIS NO..................VPL-VW12HT RM-PJVW10 WORLD WORLD VIDEO PROJECTOR...
Page 2
LES SCHÉMAS DE PRINCIPE, LES VUES EXPLOSÉES ET LES CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO- LISTES DE PIECES SONT D’UNE IMPORTANCE CRITIQUE NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR POUR LA SÉCURITÉ DU FONCTIONNEMENT. NE LES AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- REMPLACER QUE PAR DES COMPOSANTS SONY DONT LE LISHED BY SONY.
Page 3
Gerät abschaltet und signalisiert “Batterie leer” oder nach längerer Gebrauchsdauer der Batterien “nicht mehr einwandfrei funktioniert”. Um sicherzugehen, kleben Sie die Batteriepole z.B. mit einem Klebestreifen ab oder geben Sie die Batterien einzeln in einen Plastikbeutel. 1 (P) VPL-VW12HT...
Adjustment ..............2-2 2-3-3. Signal Center and the Amplitude Adjustment ......2-3 2-3-4. ODD/EVEN Level Adjustment ..........2-3 2-3-5. RGB High Gain/Bias Adjustment ..........2-3 2-3-5-1. RGB High Gain/Bias Adjustment ........ 2-3 2-3-5-2. RGB W/B Low and Custom Adjustment ..... 2-4 VPL-VW12HT...
Page 6
3-3-2-1. VIDEO Signal Flow ............. 3-7 3-3-2-2. HDTV/DTV (YPbPr, RGB) Double Speed Component (YUV) Signal Flows ... 3-7 3-3-2-3. Computer Signal (RGB) Flows ........3-7 3-3-3. SYNC Processing Flows ..............3-7 3-3-3-1. When VIDEO Signals and 15k COMPONENT Signals are Processed ... 3-7 VPL-VW12HT...
Page 7
3-4-6-2.Memory Structure and Data Access ......3-22 3-4-6-3.Data Access when VIDEO MEM OFF is Selected (When Status Memory No.1 is Selected) ..3-24 3-4-6-4.VIDEO MEM Data Access when 1 to 6 is Selected (When Status Memory No.1 is Selectsd) ..3-25 3-4-6-5.CPU Peripheral ............3-26 VPL-VW12HT...
Page 9
Q ........................ 7-3 B ......................7-11 H ......................7-15 NF ......................7-17 NR ......................7-17 TH ......................7-17 U ......................7-17 V ......................7-17 C ......................7-18 BM ......................7-30 F ......................7-32 G ......................7-32 GA ......................7-36 VPL-VW12HT...
4 Two screws (+B3 x 6) 5 Two screws (+B3 x 6) CN7001 1-3. Front Panel Assy Removal 3 Two screws (+B3 x 6) 4 Front panel assy CN5008 2 Lens cover (BT) 1 Two screws (+BVTP3 x 8) VPL-VW12HT...
7 Connector panel 3 B board Cover (9P receptacle) 1-7. Optical Unit Assy Removal • Remove the C Board (Refer to 1-5.). 2 Two screws (+PWH3 x 6) 3 Connector (2P) 1 Six screws (+PSW4 x 12) 4 Optical unit assy VPL-VW12HT...
9 V board 1-9. Power Block Removal • Remove the optical unit assy (Refer to 1-7.). 1 Four screws (+B3 x 6) Connector (3P) 2 Duct 3 Three screws (+B3 x 6) 4 Power block Fin (VW) Holder (LPS) VPL-VW12HT...
Q 5 BM----used to three extension board Q 5 C----used to one extension board B 5 BM ----used to two extension board (1)Extension of Q Board C board Q board B board BM board (2)Extension of B Board B board Q board BM board VPL-VW12HT...
S4-3 : E S3-4 : 1 S4-4 : D S3-5 : 1 S4-5 : D S3-6 : 1 S4-6 : D S3-7 : 1 S4-7 : E S3-8 : 1 S4-8 : E 4) Set Power switch as OFF (0). VPL-VW12HT...
Page 19
Cable VPL-VW12 : C board CN5002 Cable must be modified as shown below. 20 pins cable is supplied with jig, modify the other side as 8 pins. Flash jig 2, 4, 6, 8, 10, 12, 14, 16 18, 20 VPL-VW12HT...
Page 20
Timeout : 5 sec Program Mode : Boot Program Mode 3-2. Following message will be displayed. Press the START/STOP button of the adaptor board, and click 3-3. The application sends the write control program to the device. Wait for a while. 1-10 VPL-VW12HT...
Page 21
Following message is displayed. Enter the filename that you want to update, and set other items as shown below. Click OK. Start address: 00000000 End address: 0003FFFF Offset: 0 3-5. Flashing of all data is in progress. Wait for a while. 1-11 VPL-VW12HT...
Page 22
VPL-VW12 : C board CN5203 Service parts information T3 board :A-1394-975-A Cable : Registration is under way. 3. How to use the application software 3-1. Double-click the application icon to start it up. Projector must be in the stand-by mode. Click Next. 1-12 VPL-VW12HT...
Page 23
3-2.Enter the inf file that you want to upload to the projector. The rule of naming the version file (*.inf) is shown below. pw1v100f . inf version name model name 1: For VPL-PX30/20 2: For VPL-VW10/12 3-3. Set the serial communication as follows. Set baud rate to 115200 (fixed) and click Next. 1-13 VPL-VW12HT...
Page 24
Please note that the version numbers of these hex files do not necessarily match with the version numbers of *.inf file. pw*f****.hex pw*c****.hex pw*g****.hex pw*r****.hex 3-5. When upgrading of all of software is completed with success, disconnect cable from the board on the projector. Keep pressing the Power key to off the projector. 1-14 VPL-VW12HT...
(A OFF signal. portion). 8. Select the item of 02 SUB HUE. Adjust the ← or → key so that the two bars in the middle are equal in level (B portion). VPL-VW12HT...
(B portion). 1. Input the 1080/60i 100% Color Bars signal to INPUT- 9. Press the MEMORY key to save the data. A (pin 5), and select the DTV-YPbPr by the INPUT-A of the SET SETTING. VPL-VW12HT...
Level 0, and put the cursor 1 on the resumed to 1, store the adjustment data into the position shown in the figure below. memory. Cursor 1 2-3-4. ODD/EVEN Level Adjustment 1. Input the 50 IRE Flat XGA signal to INPUT-A. 8. Display the Level 7. VPL-VW12HT...
TO MEMORY” has already been implemented. So B at a total of 180 points brightness 8 levels, horizontal direction check the picture quality carefully prior to implement- 7 points, vertical direction 4 points (8 4=224 points). ing “SAVE TO MEMORY.” VPL-VW12HT...
Page 30
The device adjust menu contains important parameters for machine operations. Unnecessary operations will result in “no image” and “abnormal image.” “Factory reset” cannot be performed on device adjust menu items. (Implementing SAVE TO MEMORY will completely overwrite the data.) Do not change data unnecessarily. VPL-VW12HT...
(D2201 to 2205 / C2202 to 2206), and switches off (opens) and the CPU turns off the set. are then output through line filters (L2201 to 2205/C2210 to 2214). Stabilization of the output voltage is achieved by modulat- ing the oscillation frequency and varying the resonance VPL-VW12HT...
CN2008(pin 4). Input the IC5005(pin 28) of C Board through BM Board. The detection of the fan’s rotation speed is performed when the power is on. The change (of the fan’s rotation speed) is measured when the clogging of air filter is detected and alarmed. VPL-VW12HT...
Page 33
Power Supply Block Diagram DC (375.0V) Active Filter INLET Filter VC (19.5V) Primary sub Converter Secondary Main Converter +4.5V +6.0V +17.0V -6.0V FAN+B (13.0V) sub5v FAN CONT1 FAN1.+B FAN CONT2 FAN2.+B FAN Driver FAN PROT FAN3.+B FAN4.+B VPL-VW12HT...
Page 34
If the F board fuse (F2500), R2003 on the G board opens, the cause is an abnormal PFC circuit or abnor mal lamp power supply. There is little possibility of this being caused by the secondary side power supply. VPL-VW12HT...
When NTSC 3.58 is discriminated Y/C separation is from pin 83. After passing through low pass filters FL3008 performed by IC3014 (uPD64081). and 3007, Y is fed to pin 1 of IC3007 and C to pin 1 of When PAL, PAL-M or PAL-N are discriminated IC3008. VPL-VW12HT...
COLOR, HUE and SHARPNESS user control adjust- ments. Other processing includes detection axis adjust- ment, chroma transient improvement and conversion and output as RGB signals. Sync separation for HDTV etc. (including 3 value sync) is also performed by this IC. VPL-VW12HT...
B from (A5, B5). IC4009 switching is performed with SYNC from the computer system and 3.3 V level conversion is performed. H is then output from CN4004 (A7, B7), V from (A9, B9) and CLP from (A11, B11). VPL-VW12HT...
B24) to the microprocessor on the C board. and V is fed to pin 8. Y/G is fed to pin 11. In IC4013, SonG (SonY) automatically determines if it is dealing with C. SYNC or HV separate provides outputs from pin 29 and pin 28.
H (C) V Relay SonG Sync-sep Sync-SW INPUT B Sync-sep M52347 74VHC240 Relay H (C) V H/V/CLP H/V/CLP 5PlN CS1881 RGB.etc H (C) V Relay H (C) V Polarity Imfo. (H/L) To CPU CXA1875 • • • Signal Path. 3-13 VPL-VW12HT...
SDRAM. It also generates pulses etc. that control the IC5108 (AD9884A) PLL section using the H,V sync input from the Q board. The graphics port phase compares the H,V Sync and discriminates between interlaced and non-interlaced sync. 3-14 VPL-VW12HT...
• The 130MHz memory clock signal is obtained by multiplying the X300 21.667MHz signal by 6. The internal SDRAM operates at this frequency. Because the internal core operates at 2.5V, IC5103 (PQ20VZ1U) is used to drop the D3 3V to 2.5V. 3-15 VPL-VW12HT...
They also determine whether the output should be fed to an even pixel driver or an odd pixel driver. This switching is controlled by feeding RGT, RGT and DWN into the SELAR, SELAG, SELAB and SELB terminals. 3-16 VPL-VW12HT...
Page 47
19, 21 and 23 of line 2 are simultaneously written. Owing to use of the CXD3504R (IC5403) line memory, the After writing dot 1366, a start is made on writing lines 2 and first line is delayed by 1H relative to the second line. 3-17 VPL-VW12HT...
Page 48
CXD3504R LCX037 3. Ceiling-Front (R/B), Ceiling--Rear (G) even odd picture even picture ADV7123 CXA3512R data 1357911 24681012 M52749 (ODD) pixel even picture odd picture ADV7123 CXA3512R even 1H delay data 24681012 1357911 M52749 (EVEN) pixel CXD9512 CXD3504R LCX037 3-18 VPL-VW12HT...
Page 49
1H. Also, when scanning from left to right in the diagram, odd numbered images are filled in with odd pixels, whereas when scanning from right to left odd numbered images are filled whith even pixels. 3-19 VPL-VW12HT...
(Active data Copy) • Set Initialize • HS • HS • CH • Status • Status • Status • Chroma • Chroma Data Save • Chroma • WB • WB (Memory) • WB • Video • Video • Video 3-20 VPL-VW12HT...
Page 51
NVM memory, care must be taken not to lose either the factory adjustment data provided when the set was shipped from the factory, or any previously saved data. 3-21 VPL-VW12HT...
POWER ON. In this condition, set Åuthe FAN's CINEMA BLACK ON/OFF maximum rotation speed + correcting valueÅvas the LAMP TIMER reference value FORIGINAL of justifying the warning of the OPERATION TIMER clogging of the filter. PREVIOUS LAMP TIMER DEVICE Data FORIGINAL Data (Filter Cloggy Data) 3-22 VPL-VW12HT...
Page 53
CONTRAST STATUS MEMORY-1 VIDEO MEMORY BRIGHT DOT PHASE CHMEMORY+STATUS MEMORY-2 COLOR H SIZE H/V SHIFT SHARPNESS VIDEO MEMORY No. RGB ENHANCER DYNAMIC PIC STATUS MEMORY-2 COLOR TEMPRATURE SCAN CONVERT ON/OFF COLOR SYSTEM ASPECT Setting V SCROLL TITLE AREA 3-23 VPL-VW12HT...
CH memory data is loaded into RAM from the EEPROM the data is saved into the blocks from which the respective CH memory block. type of data was loaded. STATUS memory data is loaded into RAM from the EEPROM STATUS memory block. 3-24 VPL-VW12HT...
VIDEO memory block. The STATUS data loaded into RAM is obtained in part from the EEPROM STATUS memory block with the remainder from the VIDEO memory block. Conversely, when data is saved from RAM into EEPROM 3-25 VPL-VW12HT...
5) M52749 (DAC) : V AMP (C) POWER PROTECT Device Control I C Bus ( II ) 1) M62399 (DAC) : Panel (C) 100kbps 2) M52749 (DAC) : V AMP (C) Flash Memory Write Serial Communication RS232C Communication 3-26 VPL-VW12HT...
Page 58
COLOR TEMP HIGH COSTOM1 COSTOM2 COSTOM3 COSTOM4 COLOR SYS AUTO AUTO AUTO AUTO AUTO AUTO RGB ENHANCER DRC-MF DRCX4 DRCX4 DRCX4 DRCX4 DRCX4 DRCX4 ASPECT FULL FULL FULL FULL FULL FULL SCAN CONV V SCROLL TITLE AREA BLANKING 3-28 VPL-VW12HT...
Page 59
* : DOT PHASE • SIZE H • SHIFT H/V • SCAN CONV • ASPECT • V SCROLL • TITLE AREA • BLANKING and VIDEO MEMORY in the “INPUT SETTING” menu have an initial value respectively in accordance with the input signal (PRESET MEMORY No.). Note : There are nonadjustable items in accordance with the input signal. 3-29 VPL-VW12HT...
Page 60
V START TEMP LAMP Nonadjustable TEMP PANEL Nonadjustable LAMP FAN 1 Nonadjustable PANEL FAN 1 Nonadjustable LAMP FAN 2 Nonadjustable PANEL FAN 2 Nonadjustable GAMMA Standard Note : There are nonadjustable items in accordance with the input signal. 3-30 VPL-VW12HT...
Page 61
Fixed Value Fixed Value Fixed Value Fixed Value Fixed Value Fixed Value Fixed Value Fixed Value Fixed Value Fixed Value Fixed Value Fixed Value Fixed Value Fixed Value Fixed Value Fixed Value Fixed Value Fixed Value Fixed Value 3-31 VPL-VW12HT...
Therefore, specified parts should be used in the case of replacement. 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts common- ality and improvement. Parts list has the present standardized repair parts.
4-074-461-21 o HOOD 1-500-082-11 s CLAMP, SLEEVE FERRITE 4-074-463-02 o COVER (TP), LENS 7-682-547-04 s SCREW +B3X6 4-063-672-01 s STOPPER (LCT) 7-685-646-79 s SCREW +BVTP 3X8 4-063-686-01 s SPRING, COMPRESSION 4-063-673-01 s HOLDER (LCT) 4-074-846-01 o GUIDE (A), LED VPL-VW12HT...
Page 67
4-074-869-01 o HOLDER (RE) 7-682-547-04 s SCREW +B3X6 1-675-771-11 o PRINTED WIRING BOARD, NR 7-682-552-09 s SCREW +B3X16 4-074-863-01 o HOLDER (B) 7-682-569-09 s SCREW +B4X35(EP-FE/ZNBK/CM2) 7-682-903-11 s SCREW +PWH 3X6 7-685-646-79 s SCREW +BVTP 3X8 7-682-663-09 s SCREW +PS 4X12(EP-FE/ZNBK/CM2) VPL-VW12HT...
Page 68
4-074-856-01 s LEVER (ADJ) 7-682-547-04 s SCREW +B3X6 4-074-847-01 o HOOT (FR), ADJUSTER 7-682-569-09 s SCREW +B4X35(EP-FE/ZNBK/CM2) 4-074-849-01 o HOOT (RE), ADJUSTER 7-682-960-01 s SCREW +PSW 4X6(EP-FE/CZN-N4) X-4039-313-2 s BLOCK ASSY, FILTER 7-685-646-79 s SCREW +BVTP 3X8 7-685-648-79 s SCREW +BV3X12((EP-FE/ZNBK/CM2) VPL-VW12HT...
Page 69
9-885-000-40 o LENS(B)RELAY 9-885-027-47 s GCH OUT-POLARIZER 9-885-000-41 o LENS(C)RELAY 9-885-027-49 s BCH OUT-POLARIZER 9-885-000-42 o LENS(D)RELAY 9-885-000-37 s SET,SPACER 9-885-027-41 o LENS FLYEYE 9-885-027-40 s LENS, PROTECTION 9-885-000-27 s CONVERTER, PS 4-074-403-01 s CAP, LENS 9-885-000-25 s LENS(A),FLYEYE VPL-VW12HT...
R7004 1-216-075-00 s RESISTOR CHIP 12K 1/10W(2012) R7005 1-216-069-00 s RESISTOR,CHIP 6.8K 1/10W(2012) R7006 1-216-063-91 s RESISTOR,CHIP 3.9K 1/10W(2125) R7007 1-216-059-00 s RESISTOR,CHIP 2.7K 1/10W(2012) R7008 1-216-057-00 s RESISTOR CHIP 2.2K 1/10W(2012) R7009 1-216-053-00 s RESISTOR CHIP 1.5K 1/10W(2012) VPL-VW12HT...
Page 71
1-128-394-11 s CAPACITOR,ELECT 220MF/10V C5116 1-162-970-11 s CAPACITOR CERAMIC 0.01MF/25V B T2601 1-429-987-11 s TRANSFORMER, POWER INSULATED C5117 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF T2602 1-429-992-11 s TRANSFORMER, POWER REGULATION C5118 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C5119 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF VPL-VW12HT...
Page 72
1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C5214 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C5319 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C5215 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C5320 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C5216 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C5321 1-124-778-00 s CAPACITOR,ELECT 22MF/6.3V VPL-VW12HT...
Page 73
1-126-602-11 s CAPACITOR,ELECT 3.3MF/50V(CHIP C5637 1-128-401-11 s CAPACITOR,ELECT100MF/25V(CHIP) C5548 1-126-602-11 s CAPACITOR,ELECT 3.3MF/50V(CHIP C5638 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C5549 1-126-602-11 s CAPACITOR,ELECT 3.3MF/50V(CHIP C5639 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C5550 1-126-602-11 s CAPACITOR,ELECT 3.3MF/50V(CHIP C5640 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF VPL-VW12HT...
Page 74
8-719-159-10 s DIODE RD5.1SB-T2 C5818 1-162-970-11 s CAPACITOR CERAMIC 0.01MF/25V B D5017 8-719-159-10 s DIODE RD5.1SB-T2 C5819 1-128-400-11 s CAPACITOR, ELECT 47MF/25V D5018 8-719-914-43 s DIODE DAN202K C5820 1-162-970-11 s CAPACITOR CERAMIC 0.01MF/25V B D5202 8-719-914-43 s DIODE DAN202K 5-10 VPL-VW12HT...
Page 75
8-759-388-31 s IC PQ20VZ1U L5509 1-469-525-91 s INDUCTOR 10UH (NLFV25) IC5201 8-759-327-60 s IC TC7W125FU-TE12R L5510 1-469-525-91 s INDUCTOR 10UH (NLFV25) L5511 1-469-525-91 s INDUCTOR 10UH (NLFV25) IC5202*1 IC PW264A IC5204 8-759-544-01 s IC S-80828ANNP-EDR-T2 L5512 1-469-525-91 s INDUCTOR 10UH (NLFV25) 5-11 VPL-VW12HT...
Page 76
1-216-833-11 s RESISTOR,CHIP 10K 1/16W (1608) R5020 1-216-821-11 s RESISTOR,CHIP 1.0K 1/16W(1608) R5086 1-216-825-11 s RESISTOR,CHIP 2.2K 1/16W 1608 R5021 1-216-826-11 s RESISTOR,CHIP 2.7K 1/16W(1608) R5087 1-216-805-11 s RESISTOR,CHIP 47 1/16W 1608 R5088 1-216-809-11 s RESISTOR,CHIP 100 1/16W 1608 5-12 VPL-VW12HT...
Page 77
1-216-829-11 s RESISTOR,CHIP 4.7K 1/16W(1608) R5369 1-216-831-11 s RESISTOR,CHIP 6.8K 1/16W(1608) R5220 1-216-833-11 s RESISTOR,CHIP 10K 1/16W (1608) R5370 1-216-805-11 s RESISTOR,CHIP 47 1/16W 1608 R5221 1-216-805-11 s RESISTOR,CHIP 47 1/16W 1608 R5371 1-216-805-11 s RESISTOR,CHIP 47 1/16W 1608 5-13 VPL-VW12HT...
Page 78
1-218-672-11 s RESISTOR,CHIP 150 1/16W(1608) R5623 1-216-828-11 s RESISTOR, CHIP 3.9K 1/16W 1608 R5525 1-216-809-11 s RESISTOR,CHIP 100 1/16W 1608 R5628 1-216-864-11 s CONDUCTOR, CHIP (1608) R5526 1-216-809-11 s RESISTOR,CHIP 100 1/16W 1608 R5629 1-216-864-11 s CONDUCTOR, CHIP (1608) 5-14 VPL-VW12HT...
Page 79
1-239-409-11 s RESISTOR NETWORK 47 (1608) R5847 1-216-825-11 s RESISTOR,CHIP 2.2K 1/16W 1608 RB5323 1-239-409-11 s RESISTOR NETWORK 47 (1608) R5848 1-216-825-11 s RESISTOR,CHIP 2.2K 1/16W 1608 R5849 1-216-789-11 s RESISTOR,CHIP 2.2 1/16W(1608) RB5401 1-233-576-11 s RESISTOR,CHIP NETWORK 100 5-15 VPL-VW12HT...
Page 80
1-675-920-11 o PRINTED WIRING BOARD, TH -------- CN8400 1-580-057-11 o PIN,CONNECTOR 4P V BOARD -------- TH8400 1-808-656-11 s THERMISTOR Ref. No. or Q’ty Part No. SP Description 1-675-773-11 o PRINTED WIRING BOARD, V CN8300 1-564-517-11 o PLUG,CONNECTOR (2P)(L-TYPE) S8300 1-570-245-11 s SWITCH,MICRO 5-16 VPL-VW12HT...
Page 81
1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012) R2007 1-219-738-11 s RES, 0.08 (REGISTOR, METAL) CN2006 1-785-518-11 o CONNECTOR, BOARD TO BOARD (PLU R2101 1-202-933-61 s RESISTOR, FUSE 0.1 1/2W CN2007 1-774-248-11 o CONNECTOR, BOARD TO BOARD R2102 1-216-345-11 s RESISTOR,METAL FILM 0.47 1W 5-17 VPL-VW12HT...
Page 82
1-216-681-11 s RESISTOR,CHIP 18K 1/10W (2012) R2308 1-216-659-11 s RESISTOR,CHIP 2.2K 1/10W(2012) R2309 1-216-025-00 s RESISTOR,CHIP 100 1/10W(2012) R2310 1-216-089-91 s RESISTOR, CHIP 47K 1/10W(2012) R2311 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012) R2312 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012) 5-18 VPL-VW12HT...
Page 83
C4060 1-124-778-00 s CAPACITOR,ELECT 22MF/6.3V C4124 1-107-823-11 s CAPACITOR,CERAMIC 0.47MF/16V C4125 1-107-823-11 s CAPACITOR,CERAMIC 0.47MF/16V C4061 1-163-021-91 s CAPACITOR, CERAMIC 0.01MF/50V C4126 1-128-004-11 s CAPACITOR ELECT 10MF/16V(CHIP) C4062 1-163-021-91 s CAPACITOR, CERAMIC 0.01MF/50V C4127 1-107-823-11 s CAPACITOR,CERAMIC 0.47MF/16V 5-19 VPL-VW12HT...
Page 84
1-164-004-11 s CAPACITOR,CERAMIC 0.1MF/25V C4251 1-163-021-91 s CAPACITOR, CERAMIC 0.01MF/50V C4188 1-164-004-11 s CAPACITOR,CERAMIC 0.1MF/25V C4252 1-164-004-11 s CAPACITOR,CERAMIC 0.1MF/25V C4189 1-164-004-11 s CAPACITOR,CERAMIC 0.1MF/25V C4253 1-164-004-11 s CAPACITOR,CERAMIC 0.1MF/25V C4190 1-164-004-11 s CAPACITOR,CERAMIC 0.1MF/25V C4254 1-164-004-11 s CAPACITOR,CERAMIC 0.1MF/25V 5-20 VPL-VW12HT...
Page 85
1-412-363-11 s FERRITE, EMI (SMD) L4004 1-412-058-11 s INDUCTOR,SMALL TYPE 10UH D4022 8-719-914-43 s DIODE DAN202K L4005 1-412-058-11 s INDUCTOR,SMALL TYPE 10UH D4023 8-719-914-43 s DIODE DAN202K D4024 8-719-083-58 s DIODE UDZSTE-173.9B L4006 1-412-058-11 s INDUCTOR,SMALL TYPE 10UH 5-21 VPL-VW12HT...
Page 86
8-729-026-49 s TRANSISTOR 2SA1037AK-T146-R R4026 1-216-624-11 s RESISTOR,CHIP 75 1/10W(2012) Q4021 8-729-026-57 s TRANSISTOR FMS1A-T148 R4027 1-216-295-91 s CONDUCTOR, CHIP (2012) Q4022 8-729-026-57 s TRANSISTOR FMS1A-T148 R4028 1-216-624-11 s RESISTOR,CHIP 75 1/10W(2012) R4029 1-216-624-11 s RESISTOR,CHIP 75 1/10W(2012) 5-22 VPL-VW12HT...
Page 87
1-216-624-11 s RESISTOR,CHIP 75 1/10W(2012) R4161 1-216-017-91 s RESISTOR, CHIP 47 1/10W(2012) R4100 1-216-624-11 s RESISTOR,CHIP 75 1/10W(2012) R4162 1-216-041-00 s RESISTOR, CHIP 470 1/10W(2012) R4101 1-216-025-00 s RESISTOR,CHIP 100 1/10W(2012) R4164 1-216-017-91 s RESISTOR, CHIP 47 1/10W(2012) 5-23 VPL-VW12HT...
Page 88
1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012) R4223 1-216-295-91 s CONDUCTOR, CHIP (2012) R4290 1-216-117-00 s RESISTOR,CHIP 680K 1/10W(2012) R4224 1-216-621-11 s RESISTOR,CHIP 56 1/10W (2012) R4291 1-216-066-00 s RESISTOR,CHIP 5.1K 1/10W(2012) R4225 1-216-077-00 s RESISTOR,CHIP 15K 1/10W(2012) R4292 1-216-117-00 s RESISTOR,CHIP 680K 1/10W(2012) 5-24 VPL-VW12HT...
Page 89
1-216-095-00 s RESISTOR, CHIP 82K 1/10W(2012) R4361 1-216-097-00 s RESISTOR CHIP 100K 1/10W(2012) R4362 1-216-089-91 s RESISTOR, CHIP 47K 1/10W(2012) R4363 1-216-089-91 s RESISTOR, CHIP 47K 1/10W(2012) R4364 1-216-017-91 s RESISTOR, CHIP 47 1/10W(2012) R4365 1-216-017-91 s RESISTOR, CHIP 47 1/10W(2012) 5-25 VPL-VW12HT...
Page 90
C3055 1-164-004-11 s CAPACITOR,CERAMIC 0.1MF/25V C3056 1-163-021-91 s CAPACITOR, CERAMIC 0.01MF/50V C3057 1-163-021-91 s CAPACITOR, CERAMIC 0.01MF/50V C3059 1-164-004-11 s CAPACITOR,CERAMIC 0.1MF/25V C3060 1-126-205-11 s CAPACITOR,ELECT 47M/6.3 C3061 1-164-004-11 s CAPACITOR,CERAMIC 0.1MF/25V C3062 1-128-004-11 s CAPACITOR ELECT 10MF/16V(CHIP) 5-26 VPL-VW12HT...
Page 91
8-759-269-92 s IC SN74HCU04ANS (E20) C3133 1-164-004-11 s CAPACITOR,CERAMIC 0.1MF/25V IC3012 8-759-568-27 s IC MSM514265C-60JSDR1 C3134 1-128-004-11 s CAPACITOR ELECT 10MF/16V(CHIP) C3135 1-164-004-11 s CAPACITOR,CERAMIC 0.1MF/25V IC3014 8-759-594-44 s IC UPD64082GF-3BA C3136 1-164-004-11 s CAPACITOR,CERAMIC 0.1MF/25V IC3015 8-759-242-72 s IC TC7W00F 5-27 VPL-VW12HT...
Page 92
1-216-690-11 s RESISTOR,CHIP 43K 1/10W(2012) Q3035 8-729-026-49 s TRANSISTOR 2SA1037AK-T146-R R3056 1-216-025-00 s RESISTOR,CHIP 100 1/10W(2012) Q3036 8-729-026-49 s TRANSISTOR 2SA1037AK-T146-R R3057 1-216-025-00 s RESISTOR,CHIP 100 1/10W(2012) Q3037 8-729-026-49 s TRANSISTOR 2SA1037AK-T146-R R3058 1-216-025-00 s RESISTOR,CHIP 100 1/10W(2012) 5-28 VPL-VW12HT...
Page 93
1-216-065-91 s RESISTOR,CHIP 4.7K 1/10W(2012) R3132 1-216-017-91 s RESISTOR, CHIP 47 1/10W(2012) R3134 1-216-651-11 s RESISTOR,CHIP 1K 1/10W(2012) R3135 1-216-057-00 s RESISTOR CHIP 2.2K 1/10W(2012) R3136 1-216-295-91 s CONDUCTOR, CHIP (2012) R3137 1-216-041-00 s RESISTOR, CHIP 470 1/10W(2012) 5-29 VPL-VW12HT...
1-412-533-21 s MICRO INDUCTOR 47UH L1008 1-412-533-21 s MICRO INDUCTOR 47UH R1003 1-216-864-11 s CONDUCTOR, CHIP (1608) R1004 1-216-864-11 s CONDUCTOR, CHIP (1608) R1007 1-216-355-11 s RESISTOR,METAL FILM 3.3/1W R1008 1-216-371-00 s RESISTOR,METAL FILM 1.5/2W R1009 1-240-251-11 s RESISTOR,CEMENT 6.8/10W 5-30 VPL-VW12HT...
Page 99
RESET MCLKX SIGCEN LCD-RGT 1 OUT R PROCESS CNT1,CNT2 B-VCOM LCD-HST HCK1B HCK1 HCK1R,2R,1G,2G,1B,2B HCK2B HCH2 LCD-ENB HSDA,HSCL LCD-VCK SDA100K,SCL100K LCD-VST PW OSD ENA LCD-DWN LCD-PST COMR VCOM SIGCEN,R/G/B-VCOM HSDA,HSCL SDALOOK,SCLLOOK PW OSD ENA C, TH, U, V BLOCK VPL-VW12HT...
Page 100
(REARSIRCS RECEIVE) CN5009 LAMP LED TO C BOARD TEMP LED IC8100 CN5007 SIRCS CN8100 POWER LED SIRCS-NR P.SAVE LED D7015 ON/STBY Q7001-7003 D7002,7003,7005 Q7005-7007 D7007,7008,7010 LIGHT ON D7001 D7012-7014 D7025 D7022 D7026 D7027-7034 H/NF/NR BLOCK H, NF, NR BLOCK VPL-VW12HT...
Page 101
TO BM BOARD FAN R,SENS CN1006 Q2202-2204 P CONT CN2007 SUB+5V T2601 (SUB+5V REG) CN2011 D2601 CN2012 D2602 SUB+5V Q2601 Q2602 Q2603-2605 SWITCHING IC2603 +5V DET CONV SHUNT REG REF 8 T2602 IC2602 V REF F, G, GA BLOCK VPL-VW12HT...
Page 139
SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer : Check the metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to...