Troubleshooting - Paslode F325R Operating Manual And Schematic

OPERATOR TROUBLESHOOTING
OPERATOR TROUBLESHOOTING
OPERATOR TROUBLESHOOTING
OPERATOR TROUBLESHOOTING
PROBLEM
PROBLEM
PROBLEM
PROBLEM
Fasteners will not drive completely into wood.
Fasteners will not drive completely into wood.
Fasteners will not drive completely into wood.
Fasteners will not drive completely into wood.
Fasteners penetrate properly during normal
Fasteners penetrate properly during normal
operation, but won't drive fully at faster speeds.
Fasteners penetrate properly during normal
operation, but won't drive fully at faster speeds.
Fasteners penetrate properly during normal
operation, but won't drive fully at faster speeds.
operation, but won't drive fully at faster speeds.
Fasteners drive too deeply into wood.
Fasteners drive too deeply into wood.
Fasteners drive too deeply into wood.
Fasteners drive too deeply into wood.
Tools skips during operation - no fasteners are
Tools skips during operation - no fasteners are
driven from time to time.
Tools skips during operation - no fasteners are
driven from time to time.
Tools skips during operation - no fasteners are
driven from time to time.
driven from time to time.
Tool operates, but no fasteners are driven.
Tool operates, but no fasteners are driven.
Tool operates, but no fasteners are driven.
Tool operates, but no fasteners are driven.
Air leaks at cap when tool is connected to air.
Air leaks at cap when tool is connected to air.
Air leaks at cap when tool is connected to air.
Air leaks at cap when tool is connected to air.
CAUTION
CAUTION
CAUTION
Disconnect the tool when performing
Disconnect the tool when performing
CAUTION
Disconnect the tool when performing
repairs or clearing jams.
repairs or clearing jams.
Disconnect the tool when performing
repairs or clearing jams.
repairs or clearing jams.
14
14
14
14
14
14
14
14
CORRECTIVE ACTION
CORRECTIVE ACTION
CORRECTIVE ACTION
CORRECTIVE ACTION
Adjust work contacting element (retract length).
Adjust work contacting element (retract length).
Adjust work contacting element (retract length).
Adjust work contacting element (retract length).
Increase air pressure (do not exceed 120 psi).
Increase air pressure (do not exceed 120 psi).
Increase air pressure (do not exceed 120 psi).
Increase air pressure (do not exceed 120 psi).
Increase air flow to tool -- use larger air lines
Increase air flow to tool -- use larger air lines
(3/8 inch ID minimum).
Increase air flow to tool -- use larger air lines
(3/8 inch ID minimum).
Increase air flow to tool -- use larger air lines
(3/8 inch ID minimum).
(3/8 inch ID minimum).
Reduce air pressure.
Reduce air pressure.
Reduce air pressure.
Adjust work contacting element (extend length).
Reduce air pressure.
Adjust work contacting element (extend length).
Adjust work contacting element (extend length).
Adjust work contacting element (extend length).
Check magazine for proper fasteners. Magazine
Check magazine for proper fasteners. Magazine
follower should slide freely. Clean as needed to
Check magazine for proper fasteners. Magazine
follower should slide freely. Clean as needed to
Check magazine for proper fasteners. Magazine
remove debris.
follower should slide freely. Clean as needed to
remove debris.
follower should slide freely. Clean as needed to
remove debris.
remove debris.
Make sure correct fasteners are being used.
Make sure correct fasteners are being used.
Use fasteners that meet Paslode specifications
Make sure correct fasteners are being used.
Use fasteners that meet Paslode specifications
Make sure correct fasteners are being used.
only.
Use fasteners that meet Paslode specifications
only.
Use fasteners that meet Paslode specifications
only.
Increase air flow to tool -- use larger air lines
only.
Increase air flow to tool -- use larger air lines
(3/8 ID minimum).
Increase air flow to tool -- use larger air lines
(3/8 ID minimum).
Increase air flow to tool -- use larger air lines
(3/8 ID minimum).
Adjust work contacting element where available.
(3/8 ID minimum).
Adjust work contacting element where available.
Adjust work contacting element where available.
Adjust work contacting element where available.
Check magazine for proper fasteners. Fasteners
Check magazine for proper fasteners. Fasteners
should slide freely with no follower pressure.
Check magazine for proper fasteners. Fasteners
should slide freely with no follower pressure.
Check magazine for proper fasteners. Fasteners
should slide freely with no follower pressure.
should slide freely with no follower pressure.
Increase air pressure (do not exceed 120psi).
Increase air pressure (do not exceed 120psi).
Increase air pressure (do not exceed 120psi).
Increase air pressure (do not exceed 120psi).
Tighten cap screws.
Tighten cap screws.
Tighten cap screws.
Tighten cap screws.