Download Print this page

HOGERT HT4R625 Instruction Manual page 21

Air-powered impact wrench
Hide thumbs Also See for HT4R625:

Advertisement

CAUTION!
Potential hazard that may result in moderate injury or damage to equipment.
Verify that all connections in the air supply system are sealed in order to prevent air from leaking. Failure to comply will result
in moderate injury or damage to equipment.
Read this instruction manual thoroughly or have tool operators read thoroughly before using the tool.
Read all safety guidelines (see section "Safety guidelines") at the beginning of this manual.
Always inspect the air tool prior to each use to
- Ensure proper use of power source.
- Determine whether the tool is in proper working order.
Only use accessories which are specifi cally designed for use with this tool (see section "technical specifi cations").
Drain the compressor tank daily. Water in the air supply line will damage the tool.
Clean the air inlet and the fi lter weekly.
Line pressure should be increased to compensate for unusually long air hoses. The hose diameter should be 1/2"ID.
WARNING!
Potential hazard that will result in serious injury or loss of life.
Do not use the tool if it is not in proper working order.
Do not use oxygen or any other combustible or bottled gas to power this tool.
Do not use this tool in the presence of any fl ammable liquids or gases.
Keep hose away from heat, oil, and sharp edges. Check hose for wear and tear, and ensure that all connections are secure.
Failure to comply could lead to serious injury or loss of life.
Keep hands and other parts of the body away from the work areas when connecting the air supply. Failure to comply could lead
to serious injury or loss of life.
OPERATING INSTRUCTIONS
Loading and operation
DANGER!
Carefully read all instructions provided in this manual and understand them thoroughly before using the tool.
Do not use Impact wrench accessories other than those that are specifi cally designed for use with the Air-powered impact
wrench. Failure to comply will result in serious injury or loss of life.
Verify that the air supply is clean before operating the Air powered impact wrench.
1. Plug in compressor, turn it on set the pressure regulator to 90psi, attach one end of the air hose to the compressor and the other end
of the air hose (1) to the tool (2) . Use plumber's tape to avoid air leak ( see section" Technical specifi cations") (fi g A).
2. Place and lock the socket(1) over the square drive(2) of the Air-powered impact wrench. (fi g B)
3. Place the socket over a nut to be removed or installed and press the trigger (1)at the top of the handle to operate the tool. (fi g.C)
4. For reverse (R ) rotation, press the speed control knob (1) on the left side of the tool; For forward (F) rotation, press the speed control
knob (2) on the right side of the tool; Rotate the speed control knob (3) on the left side of the tool during reverse rotation to control
the speed of the air fl ow as required. ( Fig D ) Rotate the speed control knob (1) on the right side of the tool during forward rotation to
control the speed of the air fl ow as required.(fi g E)
5. After using the tool, disconnect the air hose (1) from the tool (2).(fi g F
WARNING!
Potential hazard that will result in serious injury or loss of life.
Hold the tool fi rmly with hands.
Do not apply additional or excessive force to the tool when working.
Do not allow the tool to run free for an extended period of time. Doing so will shorten the life of the tool.
Verify that the air supply is clean and air pressure does not exceed 90psi (6.3bar) while operating the tool. If the air pressure is
too high or unclean, it will shorten the life of the tool. Failure to comply could result in serious injury or loss of life.
Adres producenta/ Adresse des Herstellers/ Manufacturer's Address/ Адрес производителя
GTV Poland Sp. z o.o. Sp. k., ul. Przejazdowa 21, 05-800 Pruszków
21

Advertisement

loading