Advertisement
Risk of burns:
The pump and the manifold generate high temperatures. In order to avoid burns or other injuries, do not touch the pump, the
manifold, or the transfer tube while the compressor is running. Allow the parts to cool down before handling or servicing.
Keep children away from the compressor at all times.
Risk of bursting:
Make sure the regulator is adjusted so that the compressor outlet pressure is
Make sure the regulator is adjusted so that the compressor outlet pressure is
set lower than the maximum operating pressure of the tool. Before starting the
compressor, pull the ring on the safety valve to make sure the valve moves freely.
Drain water from tank after each use. Do not weld or repair tank. Relieve all pressure in the
hose before removing or attaching accessories.
WARNING!
Potential hazard that will result in serious injury or loss of life.
Always ensure that the work piece is fi rmly secured leaving both hands free to control the tool.
Always keep your air tool clean and lubricated. Daily lubrication is essential to avoid internal corrosion and possible failure.
Do not overload the tool. Allow the tool to operate at its optimum speed for maximum effi ciency. Excessive overload can cause
the tool casing to split, and may also lead to excessive wear on moving parts and possible failure.
Use only the light weight coil hoses. For connecting the tool to the compressor coupling. Do not fi t quick change couplings
onto the tool, as the vibration can lead to damage or failure of the coupling.
Always ensure that the tool has stopped before connecting it to the air supply.
Verify that grinding accessories that are used with this tools are rated at or above the tool's speed rating (4600RPM). Failure
to properly match the accessory to the tool could result in serious personal injury.
Always ensure that the accessories are rated/ designed for use with the tool.
Ensure that the accessories are correctly and securely fastened before connecting the tool to the air supply.
Locate the compressor in a well-ventilated area. For cooling, at a minimum of 12"(31cm) away from the nearest wall.
Protect the air hose and the power cord from damage and puncture. Inspect them for weak or worn spots every week, and
replace them if necessary.
Always wear hearing protection when using the air compressor. Failure to do so may result in hearing loss.
Do not carry the compressor while it is running.
Do not operate the compressor if it is not in a stable position.
Do not operate the compressor on a rooftop or in an elevated position that could allow the unit to fall or be tipped over.
Always replace a damaged gauge before operating the unit again.
CAUTION!
Potential hazard that may result in moderate injury or damage to equipment.
Keep proper footing at all times in order to ensure correct balance.
Do not wear watches, rings, bracelets, or loose clothing when using any air tool.
For optimal safety and tool performance, inspect the tool daily in order to ensure free movement of the trigger, safety mecha-
nisms, and springs.
Keep the work area clean. A cluttered or dirty workbench may lead to an accident. Floors should be kept clear.
This tool is not a toy. Use it with caution.
Use the tool in a well-ventilated area.
Verity that the tool has stopped before putting it down after use.
Handling and storage of oil: Use with adequate ventilation. Avoid contact of oil with eyes, skin and clothing. Avoid breathing
spray or mist. Store in a tightly closed container in a cool, dry, well-ventilated area free from incompatible substances.
Do not use the tool near or below freezing temperatures, as doing so may cause tool failure.
Dnot store the tool in a freezing environment to prevent ice formation on the operating valves of the tool, as doing may
cause tool failure.
Disconnect the tool from the air supply and turn off the compressor before changing any accessories, perfor-
ming any maintenance, servicing, when the tool is not in use, when it is being handed to another person, and
when it is left unattended. Failure to comply may result in moderate injury or damage to equipment.
Use safety goggles and ear protection: Wear safety glasses with side shields when operating the tool/com-
pressor and verify that others in the work area are also wearing safety glass. requirements and must provide
protection from fl ying particles from the front and the sides. Air-powered tools are loud and the sound can
cause hearing damage. Always wear ear protection to help prevent hearing damage and loss. Failure to comply
may result in moderate injury.
Note: Recycle unwanted materials rather than disposing of it as waste. Sort the tools, hoses, and
package in specifi c categories and take them to the local recycling center or dispose of them in an environmentally safe
way.
Adres producenta/ Adresse des Herstellers/ Manufacturer's Address/ Адрес производителя
GTV Poland Sp. z o.o. Sp. k., ul. Przejazdowa 21, 05-800 Pruszków
19
Advertisement
