Table of Contents
Advertisement
Please read this user manual carefully before operating the YDFLP fiber laser. It provides
essential information regarding safety, product operation, and other necessary reference
information. For the purpose of safety operation and maximizing the performance of the fiber
laser, please strictly follow the safety notifications as below:
Make sure the +24VDC power supply is connected in the correct way. Inappropriate
●
connection might spoil the product.
You can't open the cover of this product without the permission of JPT. It might cause
●
safety issues and invalidate the warranty.
Please wear laser goggle, as shown in Fig.1, all the time during the operation. This laser
●
module carry a Class 4 Laser rating it emits invisible laser radiation with a rated average output
power of over 10W and rated peak power of over 7kW. Contact with direct or scattered laser
radiation will cause permanent damage to the eyes, burn human tissue and start fires.
Attention: Even at 0% power setting, the average output power is still about 90mW.
●
File Number: EFLP001-B
Safety
Table 1 Safety Labels
Symbols
Shenzhen JPT Opto -Electronics Co. Ltd.
1
YDFLP-C-30-M7-S-X user manual
Information
Laser Warning Triangle -L
abel of laser emission (At
tached near the output fib
er)
CAUTIONS IN USE（Att
ached on the
cover plate）
Version :B Date:2020. 8
Advertisement
Table of Contents
Related Manuals for JPT YDFLP M Series
Summary of Contents for JPT YDFLP M Series
- Page 1 Make sure the +24VDC power supply is connected in the correct way. Inappropriate ● connection might spoil the product. You can’t open the cover of this product without the permission of JPT. It might cause ● safety issues and invalidate the warranty.
- Page 2 YDFLP-C-30-M7-S-X user manual Parameter Information (Attached on the cover plate) Figure 1 Laser Safety Goggle File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8...
-
Page 3: Table Of Contents
6. MAINTENANCE, CUSTOMER SERVICE AND REPAIR................23 6.1 S ............................23 TANDARD WARRANTY 6.2 W .............................23 ARRANTY LIMITATION 6.3 S ..........................24 ERVICE AND AINTENANCE 6. 4 GUI C ..............................24 ONTROL File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8... -
Page 4: Product Tour
JPT MOPA fiber laser adopts the standard DB25 interface, and it’s power supplied with 24V/5A DC, which makes it a good compatibility. A photograph of a typical JPT MOPA fiber laser is as shown below. Figure 2 JPT C-type MOPA Fiber Laser File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. -
Page 5: Packaging List
(6) Never look at the fiber laser head, and please wear laser goggle when operate this fiber laser; (7) The YDFLP-C-M7 contains 16 waveform: 1ns, continuous, 2ns,4ns,6ns,8ns,13ns,20ns,30ns，45ns,60ns,80ns,100ns,150ns,200ns,250ns,350ns. If you need other pulse width, please contact us for customization. File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8... -
Page 6: Ydflp Product Series Naming Convention
YDFLP - 30—M1+—L—R: Means this is a customized product of M1+ using low mode type of optical fiber with the nominal output power @ 30W,Integrated built-in red pilot laser. File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8... -
Page 7: Technical Specifications
Power Range 0 ~ 100 Operation Temperature Range 0 ~ 40 ℃ Storage Temperature Range -10 ~ 60 ℃ Dimension 245*200*65 Package size 481*309*136 Weight Net:4.47 G.W.:6.32 File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8... - Page 8 Below is the chart that shows the change between frequency and output: Figure 3 Cut-off Frequency & Output power relationship charts File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8...
- Page 9 YDFLP-C-30-M7-S-X user manual Figure 4 Waveform File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8...
-
Page 10: Installation
Figure 5 Mechanical Dimension of Fiber Laser Module (Unit: mm) 2. Mechanical Dimension of the output isolator. Figure 6 Mechanical Dimension of the output isolator (Unit: mm) File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8... -
Page 11: Installation Steps
Figure 8 Color code of the power supply cable 3) Ensure that the control interface of the external controller can match the laser, and then connect the control cable to the laser and fix it. File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8... -
Page 12: Laser Connector
Connect to“GND”. If need power separately, please separate the PIN_A1 and PIN_2. 3.2 RS232 connector Figure 9 RS232 connector DB9 Table 7 PIN# Description No need to connect 1，4，6-9 File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8... -
Page 13: Control Interface
The system can receive the PA only after the laser is on for 12s and the MO is H. Frequency Modulation (TTL) File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8... -
Page 14: Interface Setting
Setting 4 PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8 Current ~50 % ~75 % ~87.5 % ~93.75 % File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8... - Page 15 24V power supply) the fiber laser will stop to receive the instruction. Please turn on the fiber laser power supply again if you want to recover the machine. File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8...
-
Page 16: Pulse Width Control Instruction Structure
10us after all change finished. All instruction design start with 0xA5 byte 4）Please set up low Pin19 before use the extend configuration. 3.3.3 Pulse width control instruction code File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8... -
Page 17: Pulse Energy Control Clock Diagram
(please refer to the user manual for specific pulse width). If the value of pulse width is out of the range of specified pulse width, the laser will choose the default pulse width set last time. File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8... -
Page 18: Jpt Gui
YDFLP-C-30-M7-S-X user manual 4.JPT GUI 4.1 GUI installation File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8... -
Page 19: Introduction
YDFLP-C-30-M7-S-X user manual 4.2 Introduction 1. JPT laser GUI software has: laser control, setting the default parameters, operation tips, prompt feedback, setting the control mode and the alarm monitoring. In addition, DB25 interface monitoring and internal parameter monitoring functions are available in GUI. -
Page 20: Gui Operation
If you choose the GUI control, this setting will be saved automatically after the power down, so please cancel the GUI control mode, if you don’t want to use the GUI to control the laser. File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8... - Page 21 The default SIMMER: can control the height of the first pulse, the higher the value, the larger the first pulse. [ APPROPRIATE SIMMER] File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8...
- Page 22 Default External Frequency Mode External Frequency File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8...
- Page 23 PIN9 is power latch signal and the function is enabled if checked, rising edge is effective. The default is not checked. PIN23 is for stop signal and the function is enabled if checked, low level effective, the default is not checked. File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8...
-
Page 24: Check The State Of The Laser
Then gradually increase the laser power and change the settings for the marking process. Under normal circumstances, the laser output observed using the File Number: EFLP001-B Shenzhen JPT Opto -Electronics Co. Ltd. Version :B Date:2020. 8... -
Page 25: Precautions During The Laser Operation
JPT has the right to selectively repair or replace the products which prove to be defective during the warranty and which shall be returned. The customer need to pay the repair charge if the product is not under warranty or if the reparation is not under the warranty. -
Page 26: Service And Maintenance
JPT personnel. All requests for repair or replacement under this warranty must be made as soon as possible after the defect has been noticed and must be directed to JPT or its representative in your area. Items authorized for return by us must be returned in a suitable container. Any damage noted upon receipt of the unit must be documented for appropriate claim against the carrier.