Time Date Adjust; Present Time Display; Recorded Capacity Display Function; Basic Manual Recording - Mitsubishi Electric DX-TL910U Installation And Operation Manual

<TIME DATE ADJUST>
DAYLIGHT SAVING
>>MONTH
DAY
YEAR
TIME
6. Turn the JOG dial clockwise to move the cursor (>>) to
"DAY".
When turning the JOG dial clockwise, the cursor
(>>) moves down. When turning counterclockwise,
the cursor (>>) moves up.
7. Repeat steps 4 ~ 6 to set "DAY" and "YEAR".
8. Turn the JOG dial to move the cursor (>>) to "TIME" and
turn the SHUTTLE ring clockwise twice.
• The "TIME" display reverses in color when the SHUTTLE
ring is turned the first time. When the ring is turned for the
second time, the display turns red and flashes.
<TIME DATE ADJUST>
DAYLIGHT SAVING
MONTH
DAY
YEAR
TIME
9. Turn the JOG dial to display "18" and turn the SHUTTLE
ring clockwise.
• The setting is confirmed and flashing stops.
<TIME DATE ADJUST>
DAYLIGHT SAVING
MONTH
DAY
YEAR
TIME
The time is indicated using the 24-hour system.
10. Repeat steps 8 and 9 to set "MINUTE" and "SECOND".
11. Turn the SHUTTLE ring clockwise.
• The setting is confirmed and flashing stops.
<TIME DATE ADJUST>
DAYLIGHT SAVING
MONTH
DAY
YEAR
TIME
12. Turn the SHUTTLE ring counterclockwise.
o Present time display
When turning on the unit power, the time/date display shown
to the right appears (in the case of DISPLAY MODE 3).
For setting other display modes,
"DISPLAY MODE" page 36.
INFORMATION
This unit uses 4 digits to display the year. The
allowed display range is 99 years between 1/1/
2001 ~ 31/12/2099. The unit is also equipped with
a function to automatically calculate leap years.
The date returns to the year 2001 after 31/12/
2099.
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Basic Operations
o Recorded capacity display function
OFF
10
01 Month Day
2004
00:00:00
This unit displays the used space of the specified record-
ing device (HDD) on the screen when "REMAIN HDD" of
the <REAR TERMINAL SETTINGS> screen is set to
"MAIN", "SUB". The "%" indicates the ratio detected as HDD
against the total HDD capacity. The following settings are
required to enable this function.
1) Select the device and set the remaining capacity using
OFF
10
"REMAIN HDD" of the <REAR TERMINAL SETTINGS>
28
screen (
2004
00:00:00
2) Select "3" for "DISPLAY MODE" in the <TIME DATE/
DISPLAY SETTINGS> screen (
played. When recording is stopped, the display is
cleared (with the exception of when pausing record-
OFF
10 ing). The HDD usage display appears again after a
28
few moments when recording is started once more.
2004
18:00:00
I Basic manual recording
Normal recording using manual operation is explained here.
Before starting recording, recording settings must be
checked. After checking the settings of "HDD REPEAT REC
MAIN", "HDD REPEAT REC SUB" in the <HDD SET-
TINGS> screen (
tings are made.
OFF
10
28
timer recording, settings must be made on the
2004
<TIMER PROGRAM SETTINGS> screen (
18:30:00
page 48).
see
Day of
the week
Year
01 - 01 - 2004 THU
00 : 00 : 00 15P 99% A00001
Playback interval
Minute (Single screen playback only)
Hour Second
see page 54).
During recording, the used HDD space is dis-
see page 51), the REC mode set-
Settings here are for normal recording only. For
Recorded capacity of
the Hard Disk
Alarm recording number
see page 36).
see
25