Universal digital panel meter, digital panel meters, temperature- and mains controlling, special purpose instruments for customer requirements (12 pages)
L1 FLASHING Frequency Digital display 4-digits (red) Depending on the program display, actual voltage, frequency, vector surge Displays the alarm signals, e.g. 8A 18, 8a2-L8,… 8Err98 Displays the errors with error code e.g. UFR1001 12290-0702-05 Page 3 / 25 www.ziehl.de...
8 5048 8pin (Pincode) Display the program: Press the "Set" key for 4 s in the display mode. Display the software version: Press the "Set" key for 10 s in the display mode. UFR1001 12290-0702-05 Page 4 / 25 www.ziehl.de...
Sealing facility for set point values • Control voltage AC/DC 24-270 V • Distributor housing for panel mounting 4 TE, front-to-back size 69 mm • Mounting on 35 mm mounting rails DIN EN 60715 UFR1001 12290-0702-05 Page 5 / 25 www.ziehl.de...
Instead of the industrial norms and stipulations stated in the operating instructions and applicable in Europe, you must comply with the valid and applicable regulations in the country of utilization if the device is used outside of the area of application. UFR1001 12290-0702-05 Page 6 / 25...
Open = UFR 1001 enabled, voltage, frequency, and vector surge will be evaluated Floating closing contact Y1 – Y2 (Pr 1-3) external reset Function same as pressing the Set/Reset key for >2 s Not used Neutral conductor Phase L1 Phase L2 Phase L3 UFR1001 12290-0702-05 Page 7 / 25 www.ziehl.de...
1 minute. Time is only added as long as Added Time of Alarm supply-voltage is applied. Readout in display mode under Ac. Up = added time of alarms TAL, Down = alarm-counter Ac xx…Ac00 (xx=last alarm) UFR1001 12290-0702-05 Page 8 / 25 www.ziehl.de...
Device resets and starts Hint: When changing programs, all parameters of the selected program are reset to "factory settings" (see table "Factory settings"); only change the parameters after selecting the correct program. UFR1001 12290-0702-05 Page 9 / 25 www.ziehl.de...
8 VSR8 83 Ph8: a vector surge on all phases simultaneously leads to an alarm Interval during which the display is updated in … 8ddi 0. 1 2. 0 delay Display the display mode, UFR1001 12290-0702-05 Page 15 / 25 www.ziehl.de...
8al1U.8 • Press the Set key Display 8fvn 8•,,∆8 (Function / switching function) flash alternately • Set the desired switching function using the Up and Down keys • Press the Set key UFR1001 12290-0702-05 Page 16 / 25 www.ziehl.de...
Page 17
• Set the desired time using the Up and Down keys • Press the Set key Display 8rel (Relay / Parameter) flash alternately • Set the desired parameter using the Up and Down keys • Press the Set key UFR1001 12290-0702-05 Page 17 / 25 www.ziehl.de...
Display 8ddi8 0. 5 (Delay display / Current time) flash alternately • Set the desired time using the Up and Down keys • Press the Set key Display 8ddi.8 (Delay display) UFR1001 12290-0702-05 Page 18 / 25 www.ziehl.de...
• If present, remove seal (only authorised person) • Slightly lift the key cover and turn 180° • Keep keys pressed by pushing on the key cover (locked - LED flashes) until Locked – LED is permanently OFF (ON) UFR1001 12290-0702-05 Page 19 / 25 www.ziehl.de...
Delay Enable On, delay time during power up and after opening the 8Deon8 enable input Single-phase vector surge evaluation Three-phase vector surge evaluation 8ddi Delay display, to quiet down the display Simulation 8Code8 , 8Loc Code lock, sealed/locked 8Pin Pin code (factory setting 504) UFR1001 12290-0702-05 Page 20 / 25 www.ziehl.de...
Code lock is switched off, Pin code = 504 Pr selected with N, but N Implausible voltage value Select Pr without N or connect N not connected 8Loc appears in the Seal is active See 8.11 Sealing display UFR1001 12290-0702-05 Page 21 / 25 www.ziehl.de...
Front panel Identification for bottom / position downward Bar for wall mounting with screws. Bar drill hole Ø 4.2 mm / for fixing to wall with screws, Ø 4.2 Sealing max. Ø 1.8 mm UFR1001 12290-0702-05 Page 23 / 25 www.ziehl.de...
- Keep the Set key pressed until "Pr1" appears in the display - Release the Set key - Switch over to "Pr 2" with the Up/Down key - Briefly press the Set key: - Finished UFR1001 12290-0702-05 Page 24 / 25 www.ziehl.de...
Page 25
They must comply with the contents of the operating instructions, the notices attached to the device and the relevant safety regulations for constructing and operating electrical plants. Comply with the safety instructions in the operating instructions. UFR1001 12290-0702-05 Page 25 / 25...
Need help?
Do you have a question about the UFR1001 and is the answer not in the manual?
Questions and answers