MiLAN MIL-C2413 Series Installation Manual

Fast ethernet media converter for digi's media conversion system

Advertisement

R eg ul ato r y Ap p ro v a ls
FCC Class A
UL 1950
CSA C22.2 No. 950
EN60950
CE
EN55022
Class B
– EN50082-1
Can adi an EM I N o t ice
This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur
du Canada.
E uro pe an No t ic e
Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage
Directive (73/23/EEC) issued by the commission of the European Community. Compliance with these
directives implies conformity to the following European Norms:
EN55022 (CISPR 22) - Radio Frequency Interference
EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic Immunity
EN60950 (IEC950) - Product Safety
Five-Year Limited Warranty
Digi International warrants to the original consumer or purchaser that each of its products, and
all components thereof, will be free from defects in material and/or workmanship for a period of
five years from the original factory shipment date. Any warranty hereunder is extended to the
original consumer or purchaser and is not assignable.
Digi makes no express or implied warranties including, but not limited to, any implied warranty
of merchantability or fitness for a particular purpose, except as expressly set forth in this
warranty. In no event shall Digi be liable for incidental or consequential damages, costs, or
expenses arising out of or in connection with the performance of the product delivered
hereunder. Digi will in no case cover damages arising out of the product being used in a
negligent fashion or manner.
Tr ade m a r k s
Digi International™ and the Digi Logo are trademarks of Digi International. All other products and brands
are the trademarks of their respective holders. All rights reserved.
To C o nt a c t D ig i
For prompt response when calling for service information, have the following information ready:
Product serial number and rev.
Date of purchase
Vendor or place of purchase
You can reach Digi LAN technical support at 408/744-2751
Or E-mail at: sun-tech@dgii.com
Address:
1299 Orleans Drive
Sunnyvale, CA 94089
Voice:
408/744-2775
Fax:
408/744-2793
E-mail:
info@dgii.com
® Copyright 1998 Digi International
Printed in the USA
P/N: 90000206 Rev. A
MIL-C2413 Series
Fast Ethernet Media Converter for Digi's
Media Conversion System
Thumbscrews
TP
ACT
MDI-X MDI
TP
100BASE-TX
LINK
Mil-
C2413

Installation Guide

This guide includes the following:
• "Introduction" on page 2
• "Installation" on page 3
• "MDI/MDI-X" on page 3
• "Link Sentry Feature" on page 5
• "Indicators" on page 6
Installation Guide: MIL-C2413
FX
100BASE-FX
ACT
FX
TX
RX
LINK

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MIL-C2413 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for MiLAN MIL-C2413 Series

  • Page 1: Installation Guide

    • “Introduction” on page 2 • “Installation” on page 3 • “MDI/MDI-X” on page 3 • “Link Sentry Feature” on page 5 • “Indicators” on page 6 P/N: 90000206 Rev. A Installation Guide: MIL-C2413 MIL-C2413 Series Media Conversion System Thumbscrews 100BASE-FX MDI-X MDI...
  • Page 2 (subject to fiber budget of 16 dBm and collision domain restrictions). In full-duplex environments, up to 100 meters of CAT 5 UTP and for Mil-C2413 use 2 km of 62.5/125 micron multimode optical fiber and for MIL- C2413-15 use 15 km of 10/125 micron single-mode optical fiber...
  • Page 3 Installation Guide: MIL-C2413 • Supports half- and full-duplex modes In s ta l l at i on Do the following to install the MIL-C2413 Series into a redundant rack mount chassis: 1. Make any configuration changes to the module (i.e., DIP switch settings).
  • Page 4 Fiber port Fiber port UTP port switches must be enabled (in the “down” position) on the first MIL-C2413. On the second MIL-C2413, enable switches 1 and 4 (in the “down” position). Default setting for Link Sentry: All switches set in the “up” position (disabled).

Table of Contents