Table of Contents
Advertisement
Quick Links
i-PAN T10 Baseboard
Documentation version 2.0
This document applies to i-PAN T10 V1R2.
Introduction
The i-PAN T10 Baseboard is designed for a direct installation on a 10.1" capacitive touch
display. It features most peripherals needed by today's industrial panel-applications and because
of that is an ideal basis for customized flat panel PC solutions.
It is sold in combination with a 10.1" display and different CPU-modules and housing options.
Housing options range from simple (glued to back of the display), open metal mounting frame
and to a complete closed metal housing. It is designed to be a low-cost solution of the i-PAN XT-
Pro 10 panel.
Typical a Trizeps VII SOM with NXP i.MX 6 processor is used as CPU-module. It supports
Microsoft Windows Embedded Compact 7 or 2013, Linux and Android OS.
There are iMod flex-cable-connectors and solder-pads to extend the board functionality and
connect to SECO iMod-Adapters or customers peripherals.
Figure 1: i-PAN T10 Baseboard V1R1 assembled on 10.1" touch display with cover lens
Version 2.0
i-PAN T10 Baseboard
1 of 20
Advertisement
Table of Contents
Summary of Contents for Seco i-PAN T10 Baseboard
- Page 1 This document applies to i-PAN T10 V1R2. Introduction The i-PAN T10 Baseboard is designed for a direct installation on a 10.1” capacitive touch display. It features most peripherals needed by today’s industrial panel-applications and because of that is an ideal basis for customized flat panel PC solutions.
- Page 2 Bock Diagram Figure 2: Simplified Block Diagram of i-PAN T10 Baseboard V1R2 Version 2.0 i-PAN T10 Baseboard 2 of 20...
-
Page 3: Connector Positions
1 CONNECTOR POSITIONS Interfaces and connectors of i-PAN T10 Baseboard. Figure 3: Connectors of i-PAN T10 Basebaord Connectors: J200: Trizeps VII SODIMM connector J201: Trizeps VII High Speed connector J202: µSD-Card connector J217: iMod Button/I2C or UART connector J218: Raspberry Pi compatible camera connector... - Page 4 J208: SPI1_SCLK J209: SPI1_MOSI J210: SPI1_MISO J211: +3V3 J212: HEADPHONE_GND J213: HEADPHONE_L J214: HEADPHONE_R J215: MIC_OUT J219: MIC_GND Miscellanous: BATT200: Battery Connector (CR1632) S200: Fastboot button LED: D500: DUO LED (Link and Activity) Version 2.0 i-PAN T10 Baseboard 4 of 20...
-
Page 5: User Connectors
This interface may be used as USB-Slave, USB-Host or real USB-OTG port. Note that the USB-OTG port is also connected to the iMod USB/I2C connector J303. Only one of both connectors can be used at the same time! Version 2.0 i-PAN T10 Baseboard 5 of 20... - Page 6 This µSD-Card slot is powered by 3.3V. Its signals are connected to the first SD/SDIO port of the Trizeps module. It may be used to extend the storage-memory of the panel with a Micro-SD card. Version 2.0 i-PAN T10 Baseboard 6 of 20...
-
Page 7: Internal Connectors
3 INTERNAL CONNECTORS J303: iMod USB/I2C connector The iMod USB/I2C connector is a standard connector defined by SECO to allow customers to easily add functions to a baseboard. SECO offers different extension boards ranging from a simple breakout board or an additional USB-type A connector to current-, voltage-, TOF-, NFC- sensors or IO-expander boards. - Page 8 J302: iMod UART connector The iMod UART connector is a standard connector defined by SECO to allow customers to easily add functions to a baseboard. SECO offers different extension boards ranging from a simple breakout board to RS232/RS485/RS422 transceiver boards.
- Page 9 J217: iMod Button/I2C or UART connector The iMod connectors are standard connectors defined by SECO to allow customers to easily add functions to a baseboard. There are two mounting options for J217: a) iMod Button/I2C The connector got 3 GPIOs for buttons and an I2C-interface for sensors etc.
- Page 10 Note that unlike the iMod UART connector J302, only the TXD, RXD, RTS and CTS signals of the UART-interface are available. The GPIO-pins used for the buttons stay the same as on the iMod Button/I2C mounting option. Version 2.0 i-PAN T10 Baseboard 10 of 20...
- Page 11 J305: iMod CAN connector The iMod CAN connector is a standard connector defined by SECO Northern Europe to allow customers to easily add a CAN transceiver & connector to the baseboard. Signal Function Power CAN_GPIO2 Generic GPIO CAN_GPIO3 Generic GPIO...
- Page 12 J301: Display connector The i-PAN T10 baseboard is qualified to connect with a 10.1 inch display: ▪ 10.1” TFT Display; IPS technology ▪ 1280x800 resolution. ▪ 420cd/qm ▪ 3mm glas ▪ projected capactive touch. Please contact SECO Northern Europe if you require another display-specification.
- Page 13 It is possible to enable and disable the Speaker-Amp, but it is not possible to output different sounds to headphone and speaker at the same time. The same headphone and microphone signals are used by “J306: Headset 3.5mm Audio Jack (CTIA)“. Version 2.0 i-PAN T10 Baseboard 13 of 20...
- Page 14 Pro 10 the i-PAN T10 has got no UPS-feature (uninterruptable power supply), so that the time between power fail and power off is greatly dependent on the external power-source. The input voltage may be measured by ADC-input 2 of the Trizeps module (SODIMM-Pin 4). Version 2.0 i-PAN T10 Baseboard 14 of 20...
- Page 15 J302: iMod UART Connector Name Type Voltage Connected To J302-1 UART1_RI +3V3 SPIN37 J302-2 UART1_DCD +3V3 SPIN31 J302-3 UART1_DSR +3V3 SPIN29 J302-4 J302-5 +3V3 J302-6 UART1_RTS +3V3 SPIN27 J302-7 UART1_CTS +3V3 SPIN25 Version 2.0 i-PAN T10 Baseboard 15 of 20...
- Page 16 Voltage Connected To J217-1 FASTBOOT +3V3 SPIN122 SPIN43 (opt.) J217-2 SP113 +3V3 SPIN113 J217-3 SP117 +3V3 SPIN117 \RESET_IN (opt.) +3V3 SPIN26 J217-4 J217-5 +3V3 J217-6 I2C_CLK +3V3 SPIN196 UART2_RTS (opt.) +3V3 SPIN34 Version 2.0 i-PAN T10 Baseboard 16 of 20...
- Page 17 CSI_CLK_N DIFO MIPI J216.62 J502-9 CSI_CLK_P DIFO MIPI J216.64 J502-10 J502-11 CAM_PWDN +3V3 SPIN123 J502-12 CAM_GPIO +3V3 SPIN125 CAM_CLK (opt.) +3V3 SPIN88 J502-13 I2C1_CLK +3V3 SPIN94 J502-14 I2C1_DAT +3V3 SPIN96 J502-15 +3V3 Version 2.0 i-PAN T10 Baseboard 17 of 20...
-
Page 18: Specifications
Trizeps module and application use-case. A min. 12V 1A power-supply is recommended. Operating temperature °C Note: Operating conditions will differ depending on used Trizeps module and display. Version 2.0 i-PAN T10 Baseboard 18 of 20... - Page 19 Mechanical Specification Figure 3-3-1: Top-View on i-PAN T10 Baseboard V1R2 Dimensions: i-PAN T10 Baseboard: 130.0 x 100.0 x 17.0 mm (W x H x D) Version 2.0 i-PAN T10 Baseboard 19 of 20...
-
Page 20: Important Notice
This datasheet might contain errors. Product-specification may change without further notice. If you need to rely on a feature or specification, please contact SECO Northern Europe GmbH before placing an order. This product is sold in multiple configurations and housing options.