Proxim Tsunami MP.11 Installation And Management Manual
  1. Manuals
  2. Brands
  3. Proxim Manuals
  4. Network Hardware
  5. Antenna Tsunami MP.11
  6. Installation and management manual

Proxim Tsunami MP.11 Installation And Management Manual

Hide thumbs Also See for Tsunami MP.11:
Table of Contents

Advertisement

Quick Links

Download this manual
Tsunami MP.11 Installation and Management Guide
Model 5012-SUI
Model 5054-SUI
Version 4.0.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Tsunami MP.11 and is the answer not in the manual?

Questions and answers

Related Manuals for Proxim Tsunami MP.11

Summary of Contents for Proxim Tsunami MP.11

  • Page 1 Tsunami MP.11 Installation and Management Guide Model 5012-SUI Model 5054-SUI Version 4.0.0...
  • Page 2 Safety and Regulatory Compliance Guide located on the product CD. Copyright ©2007 Proxim Wireless Corporation, San Jose, CA. All rights reserved. Covered by one or more of the following U.S. patents: 5,231,634; 5,875,179; 6,006,090; 5,809,060; 6,075,812; 5,077,753. This manual and the software described herein are copyrighted with all rights reserved.

  • Page 3: Table Of Contents

    Tsunami MP.11 5012/5054-SUI Installation and Management Contents Introduction ..............8 About This Book .
  • Page 4 Tsunami MP.11 5012/5054-SUI Installation and Management VLAN Modes ................35 Q-in-Q (VLAN Stacking) .
  • Page 5 Tsunami MP.11 5012/5054-SUI Installation and Management Wireless ................. 72 Ethernet .
  • Page 6 Tsunami MP.11 5012/5054-SUI Installation and Management Upload ................109 Reboot .
  • Page 7 Proxim eService Web Site Support ........

  • Page 8: Introduction

    Tsunami MP.11 5012/5054-SUI Installation and Management Introduction The Tsunami MP.11 5012-SUI and 5054-SUI are a flexible wireless indoor client that let you design solutions for point-to- point links and point-to-multipoint networks. It is the client or satellite side in a wireless link.

  • Page 9: Reference Manual

    Tsunami MP.11 5012/5054-SUI Installation and Management Reference Manual Reference Manual As a companion to the Installation and Management manual, the Tsunami MP.11/QB.11 Reference Manual provides the following supplemental information: • Command Line Interface: Documents the text-based configuration utility’s keyboard commands and parameters.

  • Page 10: Wireless Network Topologies

    Introduction Tsunami MP.11 5012/5054-SUI Installation and Management Wireless Network Topologies Wireless Network Topologies The unit can be used in various network topologies and combinations. The required equipment depends upon the wireless network topology you want to build. Make sure all required equipment is available before installing the unit.
  • Page 11 Introduction Tsunami MP.11 5012/5054-SUI Installation and Management Wireless Network Topologies Up to 250 SUs can be connected to a BSU. If a BSU already has 250 SU, a new SU cannot be connected to the BSU. In this figure, the system is designed as follows: •...

  • Page 12: Management And Monitoring Capabilities

    Proxim provides these MIB files on the CD included with your unit. You must compile one or more of these MIB files into your SNMP program’s database before you can manage your unit using SNMP. See the documentation that came with your SNMP manager for instructions about how to compile MIBs.
  • Page 13 Tsunami MP.11 5012/5054-SUI Installation and Management Management and Monitoring Capabilities IMPORTANT! The remainder of this User Guide discusses installing the unit and managing it using the Web interface only. For information on managing the unit via the CLI, see the Tsunami MP.11/QB.11 Reference Manual.

  • Page 14: Installation And Initialization

    Logging in to the Web Interface Hardware Overview The 5012/5054-SUI is an full-featured indoor Subscriber Unit (SU) that is fully compatible with Tsunami MP.11 Model 5054, 954-R, 5054-R, and 5054-R-LR Base Station Units (BSUs). The unit is designed for desk-, wall-, or ceiling mounting. It is powered either through DC power or through Power-Over- Ethernet (see Power-over-Ethernet), and is equipped with the following connectors and controls: •...

  • Page 15: Led Indicators

    Installation and Initialization Tsunami MP.11 5012/5054-SUI Installation and Management Hardware Overview Reload button Power Ethernet RS-232 Reset button LED Indicators The top panel of the unit has the following LED indicators: Ethernet Wireless Power Power-over-Ethernet The 5012/5054-SUI comes with a 110/220 VAC Power Supply that has a barrel plug for the power jack in the back of the unit.

  • Page 16: Product Package

    Installation and Initialization Tsunami MP.11 5012/5054-SUI Installation and Management Product Package Product Package Each 5012/5054-SUI shipment includes the items in the following table. Verify that you have received all parts of the shipment. NOTE: Unless noted in this table, cables are not supplied with the unit.
  • Page 17 Installation and Initialization Tsunami MP.11 5012/5054-SUI Installation and Management Product Package 15 dBi Window Antenna (included with 5012-SUI-WA-xx and 5054-SUI- WA-xx; available for order separately) Outdoor Antenna Mounting Quantity Description Hardware and Documentation (included with 5012-SUI-WA-xx and 2 ea L-Type Mounting Plate (top)

  • Page 18: Installation Procedure

    Installation and Initialization Tsunami MP.11 5012/5054-SUI Installation and Management Installation Procedure Installation Procedure The following installation procedure provides instructions for attaching both the power and Ethernet connectors. In situations without an external antenna (for example, during a desk tryout), the antenna cable is not required. If you are already familiar with this type of product, you can use the Quick Install Guide for streamlined installation procedures.

  • Page 19: Step 1: Find A Suitable Location

    To make optimal use of the 5012/5054-SUI, you must find a suitable location for the hardware. The range of the unit largely depends upon the position of the antenna. Proxim recommends you do a site survey, observing the following requirements, before mounting the 5012/5054-SUI hardware.

  • Page 20: Step 3: Attach Cables

    Installation and Initialization Tsunami MP.11 5012/5054-SUI Installation and Management Installation Procedure Step 3: Attach Cables Cabling without Power Over Ethernet (PoE) 1. Plug the barrel of the power cable from the power supply into the power jack (the leftmost port in the back of the unit, see figure).

  • Page 21: Step 4: Install The Security Cover (Optional)

    Installation and Initialization Tsunami MP.11 5012/5054-SUI Installation and Management Installation Procedure Step 4: Install the Security Cover (Optional) You can optionally install a security cover to deter unauthorized access to the 5012/5054-SUI. The security cover is a plastic enclosure that prevents access to the cabling and the Reset and Reload buttons.

  • Page 22: Step 5: Mount The Unit

    Installation and Initialization Tsunami MP.11 5012/5054-SUI Installation and Management Installation Procedure Step 5: Mount the Unit The following are the mounting options for the 5012/5054-SUI: • Wall Mounting • Ceiling Mounting Wall Mounting Follow these steps to mount the unit on a wall: 1.

  • Page 23: Step 6: Power On The Unit

    Installation and Initialization Tsunami MP.11 5012/5054-SUI Installation and Management Installation Procedure Step 6: Power On the Unit The 5012/5054-SUI can be powered by a power supply (just plug the power adaptor into an AC power outlet), or by Active Ethernet (connect an Active Ethernet DC injector to the Ethernet cable).

  • Page 24: Step 8: Connect The Pigtail Cable

    Replace one of the small plastic caps onto the remaining open hole on the front. 4. Refer to the Tsunami MP.11 Antenna Installation Guide for information on how to cable the pigtail to the antenna, as well as for the mounting and connection of antennas.

  • Page 25: Step 9: Align The Antenna

    Installation and Initialization Tsunami MP.11 5012/5054-SUI Installation and Management Installation Procedure Step 9: Align the Antenna Antenna Alignment Display (AAD) provides a measurement of signal quality in an easy-to-interpret manner—a numeric printed signal value at the CLI. The SNR is numerically displayed on the CLI by two decimal characters representing a number from 00 to 99.

  • Page 26: Initialization

    10.0.0.1 configured. ScanTool lets you find the IP address of a Tsunami MP.11 5012/5054-SUI by referencing the MAC address in a Scan List, or to assign an IP address if the correct one has not been assigned. The tool automatically detects the units installed on your network segment, regardless of IP address, and lets you configure each unit’s IP settings.
  • Page 27 Installation and Initialization Tsunami MP.11 5012/5054-SUI Installation and Management Initialization 3. To set the IP address manually, ensure that Static is selected as the IP Address Type and fill in the IP Address and Subnet Mask suitable for the LAN subnet to which the unit is connected.

  • Page 28: Logging In To The Web Interface

    Installation and Initialization Tsunami MP.11 5012/5054-SUI Installation and Management Logging in to the Web Interface Logging in to the Web Interface The Web Interface provides a graphical user interface through which you can easily configure and manage the 5012/ 5054-SUI. This section describes only how to access the Web Interface; the Web Interface itself described in Basic Management.

  • Page 29: System Overview

    Tsunami MP.11 5012/5054-SUI Installation and Management System Overview This chapter provides an overview of the system. See the following sections: • Basic Configuration Information – Country and Related Settings – Dynamic Frequency Selection (DFS) – Transmit Power Control • SU Registration •...

  • Page 30: Country And Related Settings

    System Overview Tsunami MP.11 5012/5054-SUI Installation and Management Basic Configuration Information Country and Related Settings The unit’s Configure System window provides a selectable Country field that automatically provides the allowed bandwidth and frequencies for the selected country/band. Units sold only in the United States are pre-configured to scan and display only the outdoor frequencies permitted by the FCC.

  • Page 31: Transmit Power Control

    System Overview Tsunami MP.11 5012/5054-SUI Installation and Management Basic Configuration Information The SU also comes up in scan mode to scan all available frequencies to find a BSU with which it can register. Scanning may take several minutes. After establishing a wireless link, the wireless LED stops flashing and continues to shine green.
  • Page 32 System Overview Tsunami MP.11 5012/5054-SUI Installation and Management Basic Configuration Information NOTE: When the system is set to transmit at the maximum power, professional installers must ensure that the maximum EIRP limit is not exceeded. To achieve this, they may have to add attenuation between the device and the antenna when a high gain antenna is used.

  • Page 33: Su Registration

    System Overview Tsunami MP.11 5012/5054-SUI Installation and Management SU Registration SU Registration The list of parameters you must configure for registration of the SU on a BSU are: • Network Name • Base Station System Name (when used; otherwise, leave blank) •...

  • Page 34: Dynamic Data Rate Selection (Ddrs)

    Dynamic Data Rate Selection (DDRS) Dynamic Data Rate Selection (DDRS) NOTE: DDRS is configured on the BSU. See the Tsunami MP.11-R Installation and Management Guide for more information. The WORP Dynamic Data Rate Selection (DDRS) lets the BSU and SUs monitor the remote average signal-to-noise ratio (SNR) and the number of retransmissions between the BSU and SUs and adjust the transmission data rate to an optimal value to provide the best possible throughput according to the current communication conditions and link quality.

  • Page 35: Virtual Local Area Networks (Vlans)

    Virtual Local Area Networks (VLANs) Virtual Local Area Networks (VLANs) NOTE: VLANs are configured on the Base Station Unit. See the Tsunami MP.11-R Installation and Management Guide for more information. Virtual Local Area Networks (VLANs) are logical groupings of network hosts. Defined by software settings, other VLAN members or resources appear (to connected hosts) to be on the same physical segment, no matter where they are attached on the logical LAN or WAN segment.

  • Page 36: Q-In-Q (Vlan Stacking)

    System Overview Tsunami MP.11 5012/5054-SUI Installation and Management Virtual Local Area Networks (VLANs) Mixed Mode Mixed mode is available on both the SU and the BSU. It is used when the devices behind the SU send both tagged and untagged data. Frames to and from the Ethernet interface behind the SU can be tagged or untagged.

  • Page 37: Bsu In Trunk Mode And Su In Trunk/Access Mode

    System Overview Tsunami MP.11 5012/5054-SUI Installation and Management Virtual Local Area Networks (VLANs) BSU Function – Transparent Mode SU Function – Transparent Mode • BSU forwards both tagged and untagged • SU forwards both tagged and untagged frames frames received from the Ethernet interface or received from the Ethernet interface or from from any of the associated SUs.
  • Page 38 System Overview Tsunami MP.11 5012/5054-SUI Installation and Management Virtual Local Area Networks (VLANs) BSU Function – Trunk Mode SU Function – Trunk Mode SU Function – Access Mode • Up to 256 VLAN IDs can be • Up to 16 VLAN IDs can be •...

  • Page 39: Bsu In Mixed Mode And Su In Mixed, Access, Or Trunk Mode

    System Overview Tsunami MP.11 5012/5054-SUI Installation and Management Virtual Local Area Networks (VLANs) BSU in Mixed Mode and SU in Mixed, Access, or Trunk Mode When the BSU is in Mixed mode, the associated SUs can be in Trunk, Access, or Mixed mode.
  • Page 40 System Overview Tsunami MP.11 5012/5054-SUI Installation and Management Virtual Local Area Networks (VLANs) BSU Function – Mixed SU Function – Mixed Mode SU Function – Trunk Mode SU Function – Access Mode Mode • Up to 256 VLAN IDs can •...
  • Page 41 System Overview Tsunami MP.11 5012/5054-SUI Installation and Management Virtual Local Area Networks (VLANs)

  • Page 42: Quality Of Service (Qos)

    Quality of Service (QoS) Quality of Service (QoS) NOTE: Quality of Service is configured on the Base Station Unit. See the Tsunami MP.11-R Installation and Management Guide for more information. The Quality of Service (QoS) feature is based on the 802.16 standard and defines the classes, service flows, and packet identification rules for specific types of traffic.
  • Page 43 System Overview Tsunami MP.11 5012/5054-SUI Installation and Management Quality of Service (QoS) b. IP Protocol List (17 = UDP) 5. Vonage VoIP DL a. Protocol Destination Port Range (8000-8001, 10000-20000) b. IP Protocol List (17 = UDP) 6. TCP a. IP Protocol List (6) 7.
  • Page 44 System Overview Tsunami MP.11 5012/5054-SUI Installation and Management Quality of Service (QoS) • Maximum sustained data rate (or Maximum Information Rate, MIR) – specified in units of 1 Kbps from 8 Kbps up to he maximum rate of 108000 Kbps per SU •...
  • Page 45 System Overview Tsunami MP.11 5012/5054-SUI Installation and Management Quality of Service (QoS) e. Minimum Reserved Traffic Rate = 2 Mbps Maximum Latency = 20 milliseconds g. Traffic Priority = 1 Note that two different VoIP Service Flow classes for each direction of traffic have been defined (index numbers 3 to 6) which follow the ITU-T standard nomenclatures: G.711 refers to a type of audio companding and encoding that produces...
  • Page 46 System Overview Tsunami MP.11 5012/5054-SUI Installation and Management Quality of Service (QoS) a. SF class: DL-2Mbps Video PIR: Streaming Video (IP/TV); PIR Priority: 1...

  • Page 47: Basic Management

    This chapter describes basic features and functionality of the unit. In most cases, configuring these basic features is sufficient. The “Glossary” in the Tsunami MP.11/QB.11 Reference Manual provides a brief explanation of the terms used. For CLI commands you can use for basic management, see “Command Line Interface” in the Tsunami MP.11/QB.11 Reference Manual.

  • Page 48: Rebooting And Resetting

    Save command, a power outage would wipe out all changes since the last reboot. For example, entering static routes takes effect immediately; however, the routes are not saved until the unit has gone through a controlled reboot. Proxim strongly recommends saving your settings immediately when you finish making changes. Rebooting When you reboot, the changes you have made become effective and the 5012/5054-SUI is restarted.
  • Page 49 Basic Management Tsunami MP.11 5012/5054-SUI Installation and Management Rebooting and Resetting If you do not have access to the unit, you can use the procedure described in Hard Reset to Factory Default as an alternative.

  • Page 50: General Configuration Settings

    Interface Parameters for more information.) • VLAN Configuration: VLANs are configured on the Base Station Unit only. See Virtual Local Area Networks (VLANs) for an overview of VLAN functionality, and the Tsunami MP.11-R Installation and Management Guide for configuration information.

  • Page 51: Monitoring Settings

    Basic Management Tsunami MP.11 5012/5054-SUI Installation and Management Monitoring Settings Monitoring Settings The unit offers various facilities to monitor its operation and interfaces. Only the most significant monitoring categories are mentioned here. • Wireless: To monitor the wireless interfaces, click Monitor > Wireless. This tab lets you monitor the general performance of the radio and the performance of the WORP Base or WORP Satellite interfaces.

  • Page 52: Security Settings

    CCM protocol is now also supported. Proxim highly recommends you change the Network Name, Encryption Key, and Shared Secret as soon as possible. To do so, click Configure > Interfaces > Wireless. The encryption key is set using the Security tab. For systems that will use roaming features, the Network Name, Encryption Key, and the Shared Secret should each be the same for all SUs that are allowed to roam as well as for all BSUs to which these SUs are allowed to roam.

  • Page 53: Default Settings

    Basic Management Tsunami MP.11 5012/5054-SUI Installation and Management Default Settings Default Settings Feature Default Setting System Name Tsunami MP.11 5012-SUI or Tsunami MP.11 5054-SUI Mode of Operation Bridge Routing Disabled IP Address Assignment Type Static IP Address 10.0.0.1 Subnet Mask 255.255.255.0...
  • Page 54 Basic Management Tsunami MP.11 5012/5054-SUI Installation and Management Default Settings Feature Default Setting Country Selection US-only device – US World device – GB DHCP Server Disabled DHCP Relay Disabled Spanning Tree Protocol Disabled Antenna Gain 0 (For DFS Threshold compensation)

  • Page 55: Upgrading The Unit

    Software CD; the server is required to transfer the downloaded file to the unit. See TFTP Server Setup. To access all resolved problems in our solution database, or to search by product, category, keywords, or phrases, go to http://support.proxim.com. You can also find links to drivers, documentation, and downloads at this link.

  • Page 56: System Status

    Deleting system traps has no effect on the operation of the 5012/5054-SUI. System traps also are sent to an SNMP manager station (if so configured). See “Alarm Traps” in the Tsunami MP.11/QB.11 Reference Manual for a list and description of the traps.

  • Page 57: Event Log

    5012/5054-SUI. The Event Log displays messages that may not be captured by System Traps, such as the Transmit Power for the Frequency Channel selected. See “Event Log Error Messages” in the Tsunami MP.11/QB.11 Reference Manual for an explanation of messages that can appear in the Event Log.

  • Page 58: Configuration

    Tsunami MP.11 5012/5054-SUI Installation and Management Configuration This section describes configuring the 5012/5054-SUI’s settings using the unit’s Web Interface. Click the Configure button to access configuration settings. The following topics are discussed in this chapter: • System Parameters • Network Parameters •...

  • Page 59: Bridge And Routing Modes

    Configuration Tsunami MP.11 5012/5054-SUI Installation and Management System Parameters • System Name: This is the system name for easy identification of the SU. The System Name field is limited to a length of 32 bytes. Use the system name of a BSU to configure the Base Station System Name parameter on an SU if you want the SU to register only with this BSU.
  • Page 60 Configuration Tsunami MP.11 5012/5054-SUI Installation and Management System Parameters A bridge works at the data-link (physical) layer of a network, copying a data packet from one network to the next network along the communications path. The default Bridging Mode is Transparent Bridging.
  • Page 61 Configuration Tsunami MP.11 5012/5054-SUI Installation and Management System Parameters If the average packet size is 1000 bytes, the overhead saved is 1.5%; With a frame size of 64 bytes, the overhead saved is 20%; and for frame sizes of 128 bytes, the saving is 10%. Network researches claim that most network traffic consists of frames smaller than 100 bytes.

  • Page 62: Network Parameters

    Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Network Parameters Network Parameters The Network tab contains the following sub-tabs. Note that the availability of some sub-tabs depends on whether the unit is in Bridge or Routing Mode. • IP Configuration •...

  • Page 63: Roaming

    Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Network Parameters Routing Mode If the device is configured in Routing mode, both Ethernet and Wireless interfaces require an IP address. The following screen is displayed: Configure or view the following parameters: •...
  • Page 64 Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Network Parameters • Fast scanning is the scanning procedure performed when the average local SNR for the current BSU is very low (below the fast scanning threshold) and the number of retransmitted frames is greater than the fast scanning retransmission threshold given in%, so that the current session should terminate as soon as possible.

  • Page 65: Dhcp Server

    SUs every time the list is updated on the BSU. For information for configuring the channel priority list on the BSU see the Tsunami MP.11-R Installation and Management Guide. Note that an SU may roam from one BSU with a bandwidth setting to another BSU with a different bandwidth setting.
  • Page 66 Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Network Parameters The following parameters are configurable: • DHCP Server Status: Verify that DHCP Relay Agent is disabled. After you have made at least one entry in the DHCP server IP Pool Table, enable DHCP Server by selecting Enable from the DHCP Server Status pull-down menu.

  • Page 67: Spanning Tree (Bridge Mode Only)

    Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Network Parameters 2. Enter the following parameters and click Add: • Start IP Address: Indicates the starting IP address that is used for assigning address to hosts on the Ethernet side in the configured subnet.

  • Page 68: Ip Routes (Routing Mode Only)

    WDS link between two units connected to the same Ethernet network creates a network loop (if spanning tree is disabled). The Spanning Tree configuration options are advanced settings. Proxim recommends that you leave these parameters at their default values unless you are familiar with the Spanning Tree protocol.
  • Page 69 Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Network Parameters Add IP Routes 1. Click the Add button; the following screen is displayed. 2. Enter the route information. 3. Click Add. The IP Address and Subnet Mask combination is validated for a proper combination.

  • Page 70: Dhcp Relay Agent (Routing Mode Only)

    Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Network Parameters DHCP Relay Agent (Routing Mode Only) NOTE: The unit must be in Routing mode to configure DHCP Relay Agent. Click Configure > Network > DHCP RA to enable the 5012/5054-SUI DHCP Relay Agent. When enabled, the DHCP relay agent forwards DHCP requests to the set DHCP server.
  • Page 71 Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Network Parameters 2. Enter your changes, and click OK.

  • Page 72: Interface Parameters

    Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Interface Parameters Interface Parameters • Wireless • Ethernet Wireless To configure the wireless interface, click Configure > Interfaces > Wireless. SUs can be placed only in WORP Satellite mode. The Wireless Outdoor Router Protocol (WORP) is a polling algorithm designed for wireless outdoor networks.
  • Page 73 If the Base Station System Name is left blank on the SU, it can register with any BSU with a matching Network Name and Network Secret. • Operational Mode: This field indicates the operational mode of the unit, depending upon the specific Tsunami MP.11. This operational mode cannot be changed as it is based upon a license file. •...
  • Page 74 Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Interface Parameters • Enable Turbo Mode (Non-DFS US Only): Check this box to enable Turbo Mode. Turbo Mode is supported only in the United States. Enabling turbo mode, in its current implementation, allows the unit to use two adjacent frequency channels to transmit and receive a signal.

  • Page 75: Ethernet

    Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Interface Parameters If the Signal-to-Noise Ratio (SNR) is not sufficient, you may need to set a lower data rate or use antennas with higher gain to increase the margin between wanted and unwanted signals. In a point-to-multipoint configuration, the BSU should have a density setting suitable for all of its registered SUs, especially the ones with the lowest signal levels (longest links).
  • Page 76 Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Interface Parameters You can set the desired speed and transmission mode by clicking on Configuration. Select from these settings for the type of Ethernet transmission: • Half-duplex means that only one side can transmit at a time.

  • Page 77: Snmp Parameters

    Click Configure > SNMP to enable or disable trap groups, and to configure the SNMP management stations to which the 5012/5054-SUI sends system traps. See “Trap Groups” in the Tsunami MP.11/QB.11 Reference Manual for a list of the system traps.
  • Page 78 Configuration Tsunami MP.11 5012/5054-SUI Installation and Management SNMP Parameters...

  • Page 79: Management Parameters

    Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Management Parameters Management Parameters Use the Management tab to configure passwords and other service parameters. Passwords The Password tab lets you configure the SNMP, Telnet, and HTTP (Web Interface) passwords. For all password fields, the passwords must be between 6 and 32 characters. Changes take effect immediately after you click OK.
  • Page 80 NOTE: To use HyperTerminal for CLI access, make sure to check “Send line ends with line feeds” in the ASCII Setup window (in the HyperTerminal window, click Properties; then select Setup > ASCII Setup. See “HyperTerminal Connection Properties” in the Tsunami MP.11/QB.11 Reference Manual for more information). •...
  • Page 81 Serial Configuration Settings The serial port interface on the unit is enabled at all times. See “Serial Port” in the Tsunami MP.11/QB.11 Reference Manual for information about how to access the CLI interface through the serial port. You can configure and view following parameters: •...

  • Page 82: Security Parameters

    Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Security Parameters Security Parameters MAC Authentication (BSU Only) MAC authentication is available only for BSUs. Encryption NOTE: Be sure to set the encryption parameters and change the default passwords. You can protect the wireless data link by using encryption. In addition to Wi-Fi Protected Access (WPA) and Wired Equivalent Privacy (WEP), the unit supports Advanced Encryption Standard (AES) 128-bit encryption.

  • Page 83: Filtering Parameters

    LAN data from being bridged to an untrusted remote network or the Internet. To prevent blocking your own access (administrator) to the unit, Proxim recommends that IP (0x800) and ARP (0x806) protocols are always passed through.

  • Page 84: Ethernet Protocol

    Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Filtering Parameters consume valuable wireless bandwidth. On some networks, there are so many ARP broadcasts that the performance of the wireless network will degrade due to the amount of bandwidth being consumed by these messages.

  • Page 85: Static Mac Address Filtering

    Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Filtering Parameters – Enter the Protocol Number. See http://www.iana.org/assignments/ethernet-numbers for a list of protocol numbers. – Enter the Protocol Name. – Click Add. Edit/Delete Entries in the Filter Table 1. Click Edit and change the information, or select Enable, Disable, or Delete from the Status drop-down menu.
  • Page 86 Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Filtering Parameters • Wired Server: 00:40:F4:1C:DB:6A • Wireless Client 1: 00:02:2D:51:94:E4 • Wireless Client 2: 00:02:2D:51:32:12 • Wireless Client 3: 00:20:A6:12:4E:38 Prevent Two Specific Devices from Communicating Configure the following settings to prevent the Wired Server and Wireless Client 1 from communicating: •...
  • Page 87 Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Filtering Parameters network use a specific multicast address (such as 01:00:5E:00:32:4B) to exchange information, you can set up a filter to prevent these multicast packets from being forwarded to the wireless network: •...

  • Page 88: Storm Threshold

    Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Filtering Parameters • Wireless Mask: Enter the appropriate bit mask to specify the range of MAC addresses to which this filter is to apply. To specify only the single MAC address you entered in the Wireless MAC Address field, enter 00:00:00:00:00:00 (all zeroes).

  • Page 89: Ip Access Table Filtering

    Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Filtering Parameters Click the Edit Table Entries button to display an editable window such as the following. You can configure whether this traffic must be blocked for Ethernet to wireless, wireless to Ethernet, or both.
  • Page 90 Configuration Tsunami MP.11 5012/5054-SUI Installation and Management Filtering Parameters Add Entries to the IP Access Table To add an entry, click the Add Table Entries button, specify the IP address and mask of the wireless stations to which you want to grant access, and click Add.

  • Page 91: Rip Parameters (Routing Mode Only)

    Configuration Tsunami MP.11 5012/5054-SUI Installation and Management RIP Parameters (Routing Mode Only) RIP Parameters (Routing Mode Only) Routing Internet Protocol (RIP) is a dynamic routing protocol you can use to help automatically propagate routing table information between routers. The unit can be configured as RIPv1, RIPv2, RIPv1 Compatible, or a combination of the three versions while operating in Routing mode.

  • Page 92: Rip Example

    Configuration Tsunami MP.11 5012/5054-SUI Installation and Management RIP Parameters (Routing Mode Only) RIPv1 RIPv2 RIPv1 Compatible Metric-Hops Metric-Hops Metric-Hops Maximum Distance 15 Maximum Distance 15 Maximum Distance 15 RIP Example In the following example, assume that both the BSU and the SUs all are configured in Routing mode with RIP enabled to send and receive on both the Ethernet and Wireless interfaces.

  • Page 93: Nat (Routing Mode Only)

    Configuration Tsunami MP.11 5012/5054-SUI Installation and Management NAT (Routing Mode Only) NAT (Routing Mode Only) The NAT (Network Address Translation) feature lets hosts on the Ethernet side of the SU transparently access the public network through the BSU. All hosts in the private network can have simultaneous access to the public network.

  • Page 94: Supported Session Protocols

    Configuration Tsunami MP.11 5012/5054-SUI Installation and Management NAT (Routing Mode Only) Add Entries to the NAT Static Mapping Table 1. Click the Add Table Entries button. 2. Enter the following information, and click Add: • Enter the Local IP Address of the host on the Ethernet side of the SU.
  • Page 95 Configuration Tsunami MP.11 5012/5054-SUI Installation and Management NAT (Routing Mode Only) Protocol Support Applications Limitations H.323 H.323 ALG Multimedia conferencing HTTP Port mapping for inbound Web browser connection. TFTP Port mapping for inbound File transfer connection. Telnet Port mapping for inbound Remote login connection.

  • Page 96: Monitoring

    Tsunami MP.11 5012/5054-SUI Installation and Management Monitoring This section describes using the Web interface to obtain detailed information about the settings and performance of the 5012/5054-SUI. Click the Monitor button to access this information. The following tabs appear in the Monitor section: •...

  • Page 97: Wireless

    Monitoring Tsunami MP.11 5012/5054-SUI Installation and Management Wireless Wireless General Click Monitor > General to monitor the general performance of the wireless interface. WORP Click Monitor > Wireless > WORP to monitor the performance of the WORP interface. Possible values for the Registration Last Reason field are as follows: •...
  • Page 98 Monitoring Tsunami MP.11 5012/5054-SUI Installation and Management Wireless • Maximum number of SUs reached • Authentication failure • Roaming • No response from SU within the Registration Timeout Period • Low Signal Quality...

  • Page 99: Icmp

    Monitoring Tsunami MP.11 5012/5054-SUI Installation and Management ICMP ICMP Click Monitor > ICMP to view the number of ICMP messages sent and received by the 5012/5054-SUI. It includes ping, route, and host unreachable messages.

  • Page 100: Per Station

    Monitoring Tsunami MP.11 5012/5054-SUI Installation and Management Per Station Per Station Click Monitor > Per Station to view Station Statistics. On the SU, the “Per Station” page shows statistics of the BSU to which the SU is registered. The page’s statistics refresh every 4 seconds.

  • Page 101: Features

    Monitoring Tsunami MP.11 5012/5054-SUI Installation and Management Features Features Click Monitor > Features to view the features supported on the unit. NOTE: The 5012/5054-SUI shows how many Ethernet hosts it supports on its Ethernet port as the “Max Users on...

  • Page 102: Link Test

    Monitoring Tsunami MP.11 5012/5054-SUI Installation and Management Link Test Link Test Click Monitor > Link Test to find out which wireless stations are in range and to check their link quality. NOTE: Link Test requires Internet Explorer version 6.0 or later. Earlier versions do not support Link Test.

  • Page 103: Interfaces

    Monitoring Tsunami MP.11 5012/5054-SUI Installation and Management Interfaces Interfaces Click Monitor > Interfaces to view detailed information about the IP-layer performance of the unit’s interfaces. There are two sub-tabs: Wireless and Ethernet. The following figures show both interfaces.

  • Page 104: Ip Arp Table

    Monitoring Tsunami MP.11 5012/5054-SUI Installation and Management IP ARP Table IP ARP Table Click Monitor > IP ARP Table to view the mapping of the IP and MAC addresses of all radios registered at the 5012/ 5054-SUI. This information is based upon the Address Resolution Protocol (ARP).

  • Page 105: Ip Routes

    Monitoring Tsunami MP.11 5012/5054-SUI Installation and Management IP Routes IP Routes Click Monitor > IP Routes to view all active IP routes of the 5012/5054-SUI. These can be either static or dynamic (obtained through RIP). This tab is available only in Routing mode, and you can add routes only when in Routing mode.

  • Page 106: Learn Table

    Monitoring Tsunami MP.11 5012/5054-SUI Installation and Management Learn Table Learn Table Click Monitor > Learn Table to view all MAC addresses the 5012/5054-SUI has detected on an interface. The Learn Table displays information relating to network bridging. It reports the MAC address for each node that the device has learned is on the network and the interface on which the node was detected.

  • Page 107: Rip

    Monitoring Tsunami MP.11 5012/5054-SUI Installation and Management Click Monitor > RIP to view Routing Internet Protocol data for the Ethernet and Wireless interfaces.

  • Page 108: Commands

    Tsunami MP.11 5012/5054-SUI Installation and Management Commands This section describes the commands that you can issue with the Web Interface. Click the Commands button to access available commands. See the following: • Download • Upload • Reboot • Reset •...

  • Page 109: Upload

    Commands Tsunami MP.11 5012/5054-SUI Installation and Management Upload Upload Click Commands > Upload to upload a configuration or log file from the unit to a TFTP server (see TFTP Server Setup for information about the SolarWinds TFTP server software located on your product installation CD).

  • Page 110: Reboot

    Commands Tsunami MP.11 5012/5054-SUI Installation and Management Reboot Reboot Click Commands > Reboot to reboot the embedded software of the 5012/5054-SUI. Configuration changes are saved and the unit is reset. CAUTION: Rebooting the unit causes all users currently connected to lose their connection to the network until the...

  • Page 111: Reset

    Commands Tsunami MP.11 5012/5054-SUI Installation and Management Reset Reset Click Commands > Reset to restore the configuration of the 5012/5054-SUI to the factory default values. You can also reset the 5012/5054-SUI by pressing the RESET button located on the side of the unit. Because this resets the unit’s current IP address, a new IP address must be assigned.

  • Page 112: Help Link

    Commands Tsunami MP.11 5012/5054-SUI Installation and Management Help Link Help Link Click Commands> Help Link to set the location of the help files of the Web Interface. Upon installation, the help files are installed in the C:\Program Files\Tsunami\[Model Name]\Help folder.

  • Page 113: Downgrade

    Commands Tsunami MP.11 5012/5054-SUI Installation and Management Downgrade Downgrade Click Commands > Downgrade to downgrade to a previous release. Downgrade currently is supported only to release 2.0.1 and later. Once you enter this command, the unit is downgraded to the specified release and is automatically rebooted.

  • Page 114: Procedures

    Tsunami MP.11 5012/5054-SUI Installation and Management Procedures This chapter describes the following procedures: • TFTP Server Setup: Prepares the TFTP server for transferring files to and from the 5012/5054-SUI. This procedure is used by the other procedures that transfer files.

  • Page 115: Tftp Server Setup

    The SolarWinds TFTP server software is located on the product installation CD, or can be downloaded from http://support.proxim.com. You can also download the latest TFTP software from SolarWind’s Web site at http://www.solarwinds.net. The instructions that follow assume that you are using the SolarWinds TFTP server software;...

  • Page 116: Web Interface Image File Download

    Procedures Tsunami MP.11 5012/5054-SUI Installation and Management Web Interface Image File Download Web Interface Image File Download In some cases, it may be necessary to upgrade the embedded software of the 5012/5054-SUI by downloading an image file. To download an image file through the Web Interface: 1.

  • Page 117: Configuration Backup

    Procedures Tsunami MP.11 5012/5054-SUI Installation and Management Configuration Backup Configuration Backup You can back up the 5012/5054-SUI configuration by uploading the configuration file. You can use this file to restore the configuration or to configure another 5012/5054-SUI (see Configuration Restore).

  • Page 118: Configuration Restore

    Procedures Tsunami MP.11 5012/5054-SUI Installation and Management Configuration Restore Configuration Restore You can restore the configuration of the 5012/5054-SUI by downloading a configuration file. The configuration file contains the configuration information of an 5012/5054-SUI. To download a configuration file through the Web Interface: 1.

  • Page 119: Soft Reset To Factory Default

    Procedures Tsunami MP.11 5012/5054-SUI Installation and Management Soft Reset to Factory Default Soft Reset to Factory Default If necessary, you can reset the 5012/5054-SUI to the factory default settings. Resetting to default settings means that you must configure the 5012/5054-SUI anew.

  • Page 120: Hard Reset To Factory Default

    Procedures Tsunami MP.11 5012/5054-SUI Installation and Management Hard Reset to Factory Default Hard Reset to Factory Default If you cannot access the unit or you have lost its password, you can reset the 5012/5054-SUI to the factory default settings. Resetting to default settings means you must configure the 5012/5054-SUI anew.

  • Page 121: Forced Reload

    Procedures Tsunami MP.11 5012/5054-SUI Installation and Management Forced Reload Forced Reload With Forced Reload, you reset the 5012/5054-SUI to the factory default settings and erase the embedded software. Use this procedure only as last resort if the 5012/5054-SUI does not boot and the Hard Reset to Factory Default”...

  • Page 122: Image File Download With The Bootloader

    ScanTool, or the Command Line Interface through the unit’s serial port. In both cases, the file is transferred through Ethernet with TFTP. Because the CLI serial port option requires a serial RS-232C cable, Proxim recommends the ScanTool option.
  • Page 123 Procedures Tsunami MP.11 5012/5054-SUI Installation and Management Image File Download with the Bootloader – Stop bits: 1 – Flow Control: None – Parity: None • Under File > Properties > Settings > ASCII Setup, enable the Send line ends with line feeds option.

  • Page 124: Troubleshooting

    Tsunami MP.11 5012/5054-SUI Installation and Management Troubleshooting This chapter helps you to isolate and solve problems with your 5012/5054-SUI. In the event this chapter does not provide a solution, or the solution does not solve your problem, check our support website at http://support.proxim.com.

  • Page 125: Communication Issues

    Troubleshooting Tsunami MP.11 5012/5054-SUI Installation and Management Communication Issues Communication Issues Two Units Are Unable to Communicate Wirelessly If a wireless link is possible after testing two units within close distance of each other, then there are two possible reasons why wireless connectivity is not possible while the MP.11 units are at their desired locations:...

  • Page 126: Setup And Configuration Issues

    Troubleshooting Tsunami MP.11 5012/5054-SUI Installation and Management Setup and Configuration Issues Setup and Configuration Issues The following issues relate to setup and configuration problems. Lost Password If you lost your password, you must reset the 5012/5054-SUI to the default settings. See Hard Reset to Factory Default.

  • Page 127: Vlan Operation Issues

    Troubleshooting Tsunami MP.11 5012/5054-SUI Installation and Management VLAN Operation Issues VLAN Operation Issues The correct VLAN configuration can be verified by “pinging” wired hosts from both sides of the device and the network switch. Traffic can be “sniffed” on the wired (Ethernet) network. Packets generated by hosts and viewed on one of the backbones should contain IEEE 802.1Q compliant VLAN headers when in Transparent mode.

  • Page 128: Link Problems

    While wireless networking emerges more and more, the number of wireless connections to networks grows every day. The Tsunami MP.11 5012/5054-SUI is one of the successful product families used by customers today who enjoy the day after day high-speed, cost-effective connections. To successfully use the connections, technicians must be able to troubleshoot the system effectively.

  • Page 129: Analyzing The Spectrum

    By turning the antenna 360 degrees, one can check from which direction the interference is coming. The analyzer will also display the frequencies and the level of signal is detected. Proxim recommends performing the test at various locations to find the most ideal location for the equipment. Avoiding Interference When a source of interference is identified and when the level and frequencies are known, the next step is to avoid the interference.

  • Page 130: A Country Codes And Channels

    Tsunami MP.11 5012/5054-SUI Installation and Management Country Codes and Channels In the CLI and MIB browser, the country code is set using the string code, as shown in the following example. Example: To set Taiwan as the country: set syscountrycode TW NOTE: The country code must be entered in capital letters.
  • Page 131 Country Codes and Channels Tsunami MP.11 5012/5054-SUI Installation and Management Channels/Frequencies by Country Country (Code) Frequency Allowed Channels (Center Freq) 20 MHz 10 MHz 5 MHz Bands Belgium (BE) 5.47 - 5.725 GHz 100 (5500), 104 (5520), 98 (5490), 100 (5500),...
  • Page 132 Country Codes and Channels Tsunami MP.11 5012/5054-SUI Installation and Management Channels/Frequencies by Country Country (Code) Frequency Allowed Channels (Center Freq) 20 MHz 10 MHz 5 MHz Bands Bulgaria (BG) 5.47 - 5.725 GHz 100 (5500), 104 (5520), 98 (5490), 100 (5500),...
  • Page 133 Country Codes and Channels Tsunami MP.11 5012/5054-SUI Installation and Management Channels/Frequencies by Country Country (Code) Frequency Allowed Channels (Center Freq) 20 MHz 10 MHz 5 MHz Bands Cyprus (CY) 5.47 - 5.725 GHz 100 (5500), 104 (5520), 98 (5490), 100 (5500),...
  • Page 134 Country Codes and Channels Tsunami MP.11 5012/5054-SUI Installation and Management Channels/Frequencies by Country Country (Code) Frequency Allowed Channels (Center Freq) 20 MHz 10 MHz 5 MHz Bands Estonia (EE) 5.47 - 5.725 GHz 100 (5500), 104 (5520), 98 (5490), 100 (5500),...
  • Page 135 Country Codes and Channels Tsunami MP.11 5012/5054-SUI Installation and Management Channels/Frequencies by Country Country (Code) Frequency Allowed Channels (Center Freq) 20 MHz 10 MHz 5 MHz Bands Greece (GR) 5.47 - 5.725 GHz 100 (5500), 104 (5520), 98 (5490), 100 (5500),...
  • Page 136 Country Codes and Channels Tsunami MP.11 5012/5054-SUI Installation and Management Channels/Frequencies by Country Country (Code) Frequency Allowed Channels (Center Freq) 20 MHz 10 MHz 5 MHz Bands Iceland (IS) 5.47 - 5.725 GHz 100 (5500), 104 (5520), 98 (5490), 100 (5500),...
  • Page 137 Country Codes and Channels Tsunami MP.11 5012/5054-SUI Installation and Management Channels/Frequencies by Country Country (Code) Frequency Allowed Channels (Center Freq) 20 MHz 10 MHz 5 MHz Bands Ireland 5.8 GHz (I1) 5.725 - 5.85 GHz 147 (5735), 151 (5755), 145 (5725), 147 (5735),...
  • Page 138 Country Codes and Channels Tsunami MP.11 5012/5054-SUI Installation and Management Channels/Frequencies by Country Country (Code) Frequency Allowed Channels (Center Freq) 20 MHz 10 MHz 5 MHz Bands Liechtenstein (LI) 5.47 - 5.725 GHz 100 (5500), 104 (5520), 98 (5490), 100 (5500),...
  • Page 139 Country Codes and Channels Tsunami MP.11 5012/5054-SUI Installation and Management Channels/Frequencies by Country Country (Code) Frequency Allowed Channels (Center Freq) 20 MHz 10 MHz 5 MHz Bands Malaysia (MY) 5.25 - 5.35 GHz and 56 (5280), 60 (5300), 54 (5270), 56 (5280), 53 (5265), 54 (5270), 55 (5275), 56 (5280), 5.725 - 5.85 GHz...
  • Page 140 Country Codes and Channels Tsunami MP.11 5012/5054-SUI Installation and Management Channels/Frequencies by Country Country (Code) Frequency Allowed Channels (Center Freq) 20 MHz 10 MHz 5 MHz Bands North Korea (KP) 5.725 - 5.825 GHz 149 (5745), 153 (5765), 147 (5735), 149 (5745),...
  • Page 141 Country Codes and Channels Tsunami MP.11 5012/5054-SUI Installation and Management Channels/Frequencies by Country Country (Code) Frequency Allowed Channels (Center Freq) 20 MHz 10 MHz 5 MHz Bands 98 (5490), 100 (5500), Portugal (PT) 5.47 - 5.725 GHz 100 (5500), 104 (5520),...
  • Page 142 Country Codes and Channels Tsunami MP.11 5012/5054-SUI Installation and Management Channels/Frequencies by Country Country (Code) Frequency Allowed Channels (Center Freq) 20 MHz 10 MHz 5 MHz Bands 30 (5150), 32 (5160), Russia (RU) 5.15 - 6.08 GHz 30 (5150), 34 (5170),...
  • Page 143 Country Codes and Channels Tsunami MP.11 5012/5054-SUI Installation and Management Channels/Frequencies by Country Country (Code) Frequency Allowed Channels (Center Freq) 20 MHz 10 MHz 5 MHz Bands Saudi Arabia (SA) 5.15 - 5.35 GHz and 36 (5180), 40 (5200), 36 (5180), 38 (5190), 36 (5180), 37 (5185), 38 (5190), 39 (5195), 5.725 - 5.825 GHz...
  • Page 144 Country Codes and Channels Tsunami MP.11 5012/5054-SUI Installation and Management Channels/Frequencies by Country Country (Code) Frequency Allowed Channels (Center Freq) 20 MHz 10 MHz 5 MHz Bands South Africa (ZA) 5.47 - 5.725 GHz 100 (5500), 104 (5520), 98 (5490), 100 (5500),...
  • Page 145 Country Codes and Channels Tsunami MP.11 5012/5054-SUI Installation and Management Channels/Frequencies by Country Country (Code) Frequency Allowed Channels (Center Freq) 20 MHz 10 MHz 5 MHz Bands Taiwan (158) 5.25 - 5.35 GHz and 56 (5280), 60 (5300), 54 (5270), 56 (5280), 53 (5265), 54 (5270), 55 (5275), 56 (5280), 5.725 - 5.825 GHz...
  • Page 146 Country Codes and Channels Tsunami MP.11 5012/5054-SUI Installation and Management Channels/Frequencies by Country Country (Code) Frequency Allowed Channels (Center Freq) 20 MHz 10 MHz 5 MHz Bands 56 (5280), 60 (5300), 54 (5270), 56 (5280), United States 5.25 - 5.35 GHz and DFS (U1) 5.47 - 5.725 GHz...

  • Page 147: B Technical Specifications

    Tsunami MP.11 5012-SUI 5 GHz with 15 dBi Window Antenna, UK 5012-SUI-WA-US Tsunami MP.11 5012-SUI 5 GHz with 15 dBi Window Antenna, US/CAN 5012-SUI-WA-US-WORLD Tsunami MP.11 5012-SUI 5 GHz with 15 dBi Window Antenna, World, US/CAN PSU 5054-SUI Part Number Description 5054-SUI-EU Tsunami MP.11 5054 Indoor Subscriber Unit, EU PSU...

  • Page 148: Accessories

    Outdoor Ethernet Cables Part Number Description 69819 25m outdoor, terminated CAT5 cable for Tsunami MP.11 or QB.11 with three RJ-45 and one weather-proof Ethernet port cap 69820 50m outdoor, terminated CAT5 cable for Tsunami MP.11 or QB.11 with three RJ-45...

  • Page 149: Regulatory Approval And Frequency Ranges

    Technical Specifications Tsunami MP.11 5012/5054-SUI Installation and Management Regulatory Approval and Frequency Ranges Regulatory Approval and Frequency Ranges Region/Country Country Number of Channels Certification 5 MHz 10 MHz 20 MHz North America 5.25 - 5.35 Up to 30 Up to 14 Yes* 5.47 - 5.725...

  • Page 150: Radio And Transmission Specifications

    Technical Specifications Tsunami MP.11 5012/5054-SUI Installation and Management Radio and Transmission Specifications Regulatory Approval and Frequency Ranges (continued) Region/Country Country Number of Channels Certification 5 MHz 10 MHz 20 MHz South America Argentina 5.25 - 5.35 Up to 9 Up to 5 Up to 3 5.725 - 5.85...

  • Page 151: Maximum Throughput

    Technical Specifications Tsunami MP.11 5012/5054-SUI Installation and Management Maximum Throughput Maximum Throughput NOTE: Actual throughput performance in the field may vary. 5012-SUI Data Rate 20 MHz Channels 10 MHz Channels 5 MHz Channels 12 Mbps 9 Mbps 9 Mbps 8 Mbps...

  • Page 152: Interfaces

    Technical Specifications Tsunami MP.11 5012/5054-SUI Installation and Management Interfaces Interfaces Category Specification Wired Ethernet Wired Ethernet 10/100Base-TX Ethernet (RJ-45) RS-232 Serial Connector Antenna Connector Standard Type-N Male Input Power Requirements Category Specification Power Adaptor (Wall • Input: 100 - 240 VAC, 0.4 Watts Mount) (included) •...

  • Page 153: Hardware Specifications

    Technical Specifications Tsunami MP.11 5012/5054-SUI Installation and Management Hardware Specifications Category Specification Filtering • Ethernet protocol (Ethertype) • Static MAC • Storm threshold • IP address • Broadcast protocol • Intra Cell Blocking (Configured on BSU) Services • DHCP Server (RFC 2131) •...

  • Page 154: Mtbf And Warranty

    Technical Specifications Tsunami MP.11 5012/5054-SUI Installation and Management MTBF and Warranty MTBF and Warranty Category Specification MTBF >100,000 hours Warranty 1 year parts and labor...

  • Page 155: C Technical Services And Support

    If you are having trouble utilizing your Proxim product, please review this manual and the additional documentation provided with your product. If you require additional support and would like to use Proxim’s free Technical Service to help resolve your issue, please be ready to provide the following information before you contact Proxim’s Technical Services: •...

  • Page 156: Support Options

    Priority Queuing: This service allows your product issue to be routed to the next available Customer Service Engineer. To purchase ServPak support services, please contact your authorized Proxim distributor. To receive more information or for questions on any of the available ServPak support options, please call Proxim Support at +1-408-542-5390 or send an email to servpak@proxim.com.

  • Page 157: D Statement Of Warranty

    The express warranties set forth in this Agreement will not apply to defects in a Product caused; (i) through no fault of Proxim Wireless during shipment to or from Buyer, (ii) by the use of software other than that provided with or installed in...

  • Page 158: Other Information

    Calls to the Customer Service Center for reasons other than Product failure will not be accepted unless Buyer has purchased a Proxim Wireless Service Contract or the call is made within the first thirty (30) days of the Product’s invoice date.

This manual is also suitable for:

5012-sui5054-sui

Table of Contents