Page 3
Product denomination In this manual, the product code name, IDT-IV is used for simplification purposes, instead of the official product name, ID-T741. Also, IDC-IV is used instead of ID-T742 for the same purposes. Menu or button selection on the display To select a menu or a button (icon) displayed on the screen while in the service mode, lightly touch it with the tip of a finger.
Page 4
To avoid damages to the parts/units due to static discharge, use a wrist strap putting one end on your wrist and the other end on the grounded section of the equipment, as illustrated below. Wrist strap FT100310.EPS 009-052-03 FCR ID-T741 Service Manual 9.24.99 FM2561-1 (ITC)
Page 5
FCR ID Terminal/Console ID-T741 Service Manual MAINTENANCE 009-052-04 Maintenance-0 FCR ID-T741 Service Manual 03.30.2000 FM2762 (ITC)
3.4.2 HOST information management ......21 3.4.3 IP registration information management/sharing function ..............22 3.4.4 Connection of multiple units of image reader ..23 3.4.5 Patient information on-line function ......27 009-052-03 Maintenance-0.1 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
• Patient information on-line function 1 : This battery life prevails while the power is OFF. • Radiographic equipment connection function The battery power is not consumed while the power is ON. TT100151.EPS 009-052-02 Maintenance-1 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
Mode changes effected by service engineer FT100226.EPS (5) Enter “fcr” as the password. Use the full keyboard when starting up by canceling auto logon. The entered password does not appear on the display. 009-052-02 Maintenance-2 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
Page 10
(4) Touch [AC] to delete the default password for the user’s service mode entry. The character string in the input area is then cleared. (5) Touch [123]. The upper-case alphabetical character input mode then pre- vails. 009-052-03 Maintenance-3 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Frontal and lateral images on film setup Do not turn OFF the main switch. If you turn OFF the main switch during remote power supply control, the remote power ON/OFF FT100201.EPS function is disabled. 009-052-03 Maintenance-4 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
: The backed-up data can be used as is for the other units of the IDT-IV. TT100101.EPS : The backed-up data needs to be restored and edited for use with the other units of the IDT-IV. : The setup data cannot be backed up. TT100102.EPS 009-052-03 Maintenance-5 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
The group of computers displayed, for convenience, under the same work group name when a network configuration is referred to. Leave the default as it is. Ex.: FCRIDT4 • IP address 009-052-02 Maintenance-6 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
Page 14
When connecting to RIS, make settings via the "Setting the Patient phy. Information Online Function " screen. Sets to [OFF] for 9000 series image readers. RIS cannot be selected from this screen. 009-052-02 Maintenance-7 FCR ID-T741 Service Manual 3.30.99 FM2483 (ITC)
Page 15
• Storage offset Sets the storage position for read data. For example, if "2" is set, 2 spaces will be added to the front of the data when it is stored. 009-052-02 Maintenance-8 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
Page 16
IDT. In keeping, Specifies the birth date display/input format. inputting in a mode that does not automatically generate these codes is safer. ID number setup • Character string length • Padding method 009-052-04 Maintenance-9 FCR ID-T741 Service Manual 03.30.2000 FM2762 (ITC)
Page 17
Extended interface is available from software version A07. When WX : Collective whole-spine processing using extended interface, select “LONG” because the data field length for the patient ID numbers or examination numbers has been extended. 009-052-03 Maintenance-10 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 18
Specifies whether or not to transmit exposure condition data to the X-ray controller. Implementation condition reception mode setup Specifies whether or not to receive implementation condition data from the X-ray controller. 009-052-03 Maintenance-11 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
For the functions to be used by both the service engineers and general users, refer to the operation manual. FT100011.EPS 009-052-03 Maintenance-12 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
NOTE FT100204.EPS Do not turn OFF the main switch. If you turn OFF the main switch while remote power supply control is exercised, the remote power ON/OFF function is disabled. 009-052-03 Maintenance-13 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
: Image format (image output format on film) : Distribution code (an 8-digit code that specifies the image distribution destination) : Film output count : Pixel density (sets whether standard image or high-quality image) 009-052-03 Maintenance-14 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
I. Select a selector button that defines your updating. II. Update parameters. III. Set the Auto. Exp. Control items as required. (2) Touch [OK]. You are returned to the service main screen. 009-052-04 Maintenance-15 FCR ID-T741 Service Manual 03.30.2000 FM2762 (ITC)
Page 23
0: Small focus 1000: Large focus Film sensitivity 2: Standard 0: Standard 0: Standard Detection field 3: ± 0 standard 4: ± 0 standard 4: ± 0 standard Film density TT100008.EPS 009-052-03 Maintenance-16 FCR ID-T741 Service Manual 9.24.99 FM2561-1 (ITC)
2 channels drive I/F or IDT-IV Sub-board IDT-IV, Remote power ON I/F FT100270.EPS External device (image reader) x 2 channels drive I/F or IDT-IV IDT-IV, Remote power ON I/F FT100207.EPS 009-052-03 Maintenance-17 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 25
Magnetic Reset switch Reset switch card reader Brightness control Brightness control ISO (JIS-I) or Buzzer volume control Buzzer JIS (JIS-II) ISO (JIS-I) or Buzzer volume Buzzer JIS (JIS-II) control FT100271.EPS FT100208.EPS 009-052-03 Maintenance-18 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
OFF. 5000 5000 5501 5501 Couple the IDT-IV units together by connecting their contact outputs IDT-IV IDT-IV IDT-IV and inputs. FT100210.EPS 009-052-03 Maintenance-19 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Only the master IDT is capable of editing the host information. Therefore, when adding a unit of the IDT-IV or IDC-IV to the net- work, all you have to do is update the master IDT host information. 009-052-03 Maintenance-21 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
5000 5501 5501 5501 5000 IDT-IV IDT-IV IDT-IV IDT-IV IDT-IV 9000 Series image reader IP information management group range Image readers whose image processing parameters are managed by the IDT-IV FT100217.EPS 009-052-03 Maintenance-22 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
The IDT-IV responds to the IP information inquiries sent from a net- Device that functions as the IP information gateway worked unit of the FCR5000/R. The IP registration function can be used. FT100219.EPS IP information inquiry and response 5000 5000 IDT-IV FT100051.EPS 009-052-03 Maintenance-23 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 31
When the IDT-IV is used as a console for two units of the FCR5501/2 IP information inquiry and response 5000 5501 5501 5501 5502 5502 5502 IDT-IV IDT-IV IDT-IV Image readers whose image processing parameters are managed by the IDT-IV FT100052.EPS 009-052-04 Maintenance-24 FCR ID-T741 Service Manual 03.30.2000 FM2762 (ITC)
Page 32
Manual mode. If the employed setup is such that only one selector button is used, no selector button is displayed in the screen. 009-052-03 Maintenance-25 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
RIS, using Response the patient ID number, study number, and reception number as the Inquiry key, and acquires the patient information. HOST connection IDT-IIIB FT100224.EPS Patient information Inquiry IDT-IV Response FT100221.EPS 009-052-03 Maintenance-27 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 35
Devices that acquire patient information from the IDC-III's database FT100223.EPS NOTE Since the IDT-IV has only three serial connector channels, the possible connection configuration is limited when the IDT-IV is used as the HOST. 009-052-03 Maintenance-28 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 36
IDT/CSL that has requested the information. Res- Patient ponse information Inquiry IDC-IV Inquiry Response HOST HOST HOST Response Inquiry connection connection connection 9501 CSL IDT-IV CSL-IV AC CSL Response Inquiry HOST connection IDT-IIIB FT100227.EPS 009-052-03 Maintenance-29 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
(3) Remove the seven screws from the top cover assembly. (2) [Remove] Barcode reader holder (3) [Remove] Screw x 7 Screw x 2 Equipment main unit Cable [Remove] Top cover assembly FT100102.EPS Top cover assembly FT100101.EPS 009-052-03 Maintenance-30 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
(1) Remove the top cover assembly. “4.1 Top Cover Assembly” (2) Disconnect the MCR assembly connector. Connector Equipment main unit Top cover assembly Top cover assembly FT100103.EPS FT100104.EPS To accomplish installation, reverse the removal procedure. 009-052-03 Maintenance-31 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 39
Touch panel (4) [Remove] CN1 (6) [Replace] Touch panel Screw x 1 (4) [Remove] CN4 Inverter (4) [Remove] CN5 FT100105.EPS Top cover assembly FT100106.EPS To accomplish installation, reverse the removal procedure. 009-052-03 Maintenance-32 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Screw x 1 (2) [Remove] CN2 (4) [Replace] Power supply unit Equipment Equipment main unit Claws main unit (2) [Remove] CN12 FT100107.EPS Main board FT100108.EPS To accomplish installation, reverse the removal procedure. 009-052-03 Maintenance-33 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Connector assembly Screw x 3 (6) [Replace] Hard disk Top view drive Screw x 4 (3) [Remove] CN14 Sub-board Main board Main board Floppy disk drive assembly Connection cable FT100110.EPS FT100111.EPS 009-052-03 Maintenance-34 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
(2) Disconnect the main board connectors (CN2, CN3, CN11, and CN14). If the option PC board (SIF04A board) is installed, remove it and the side cover. CN11 Top view Sub-board Main board CN14 FT100112.EPS 009-052-03 Maintenance-35 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 43
(4) [Remove] Main board assembly Screw x 3 (6) [Replace] Main board (5) [Remove] Bracket Screw x 4 FT100114.EPS the power cable from the equipment before performing the procedure below. FT100113.EPS 009-052-03 Maintenance-36 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
If the option PC board (SIF04A board) is installed, remove it. (3) Disconnect the sub-board connectors (CN4 and CN5). (4) Remove the sub-board. (3) [Remove] CN4 (4) [Remove] Sub-board Screw x 4 (2) [Remove] Side cover Screw (3) [Remove] CN5 FT100115.EPS 009-052-03 Maintenance-37 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
If the option PC board (SIF04A board) is installed, remove it and the side cover. (3) Replace the backup battery. (2) [Remove] CN4 (3) [Replace] Backup battery Sub-board (8) [Replace] LCD FT100117.EPS FT100119.EPS 009-052-03 Maintenance-39 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 47
MAINTENANCE 4. Replacement Procedures (4) Accomplish reassembly by reversing the removal steps. (5) Set the date and time. Installation, “3.3.6, Setting the system, Setting the date and time” 009-052-03 Maintenance-40 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
11 ≤ N ≤ 300 Rank A = 3 + N x Q x 0.3 Rank C = 3 + N x Q x 0.05 Rank D = 2 + N x Q x 0.02 009-052-03 Maintenance-41 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
MAINTENANCE 5. Service Parts List 5.1 Enclosure Section Enclosure BK05004.EPS 009-052-03 Maintenance-42 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
MAINTENANCE 5. Service Parts List 5.2 Base Section - Floppy Disk Drive and Sub-board Base unit BK05005.EPS 009-052-03 Maintenance-44 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
MAINTENANCE 5. Service Parts List 5.3 Base Section - Hard Disk Drive, Main Board, and Power Supply Base unit 4, 5 BK05006.EPS 009-052-03 Maintenance-46 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 54
Cable Hard disk drive connection PA01267-K020 136N7010 Cable Main switch and inlet attached PA01267-K021 136N7011 Cable Power supply-to-main board connection 379N0089 Radiating sheet PA01267-K049 SIF04A-to-main board 136Y7135 Cable connection for remote 009-052-03 Maintenance-47 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
CH-B board RIS, X-ray controller CH-C IDT-III, IR (image reader), RIS, X-ray controller Note: Remote 1 ..Remote power control output (2CH) Remote 2 ..Remote power control output (1CH) BK05008.EPS 009-052-03 Maintenance-50 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 58
VM-02, 15 m, IDT-IV-to- 136Y7138A DPR/SPR (IDT-IV master) VM-03, 30 m, IDT-IV-to- 136Y7139A DPR/SPR (IDT-IV master) VM-04, 50 m, IDT-IV-to- 136Y7140A DPR/SPR (IDT-IV master) VM-05, 100 m, IDT-IV-to- 136Y7141A DPR/SPR (IDT-IV master) 009-052-03 Maintenance-51 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 59
3 m (9-pin D sub) IDT-IV-to-RIS, 136Y5758 OP-09/VH-06, RIS terminal, 5 m (9-pin D sub) IDT-IV-to-RIS, 136Y5759 OP-09/VH-07, RIS terminal, 10 m (9-pin D sub) IDT-IV-to-RIS, 136Y5760 OP-09/VH-08, RIS terminal, 15 m (9-pin D sub) 009-052-03 Maintenance-52 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 60
For grounding the remote power 301N0005A 1~3* machine screw cables * Quantity depends on the number of cables connected. REF.1.1–1.3 Power cable REF.1.1 REF.1.2 REF.1.3 100/120VAC 230VAC 240VAC REF.1.4 Power Cable AC-3CS AC-3 BK05009.EPS 009-052-03 Maintenance-53 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 61
MAINTENANCE 5. Service Parts List 009-052-03 Maintenance-54 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 62
FCR ID Terminal/Console ID-T741 Service Manual INSTALLATION 009-052-04 Installation-0 FCR ID-T741 Service Manual 03.30.2000 FM2762 (ITC)
Provided (automatic reset type incorpo- rated). Causes the machine to shut down when a 125% condition continues for 30 seconds and achieves recovery 30 seconds later. • Power consumption 30W or less. 009-052-02 Installation-1 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
IDT-IV Device that functions as the IP information gateway FT100001.EPS Concerning groups (IP information management group) and gate- ways (IP information gateway), see Maintenance," 3.4.3 IP registration information management/sharing function." 009-052-02 Installation-2 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
Patient information on-line ID ONLINE SOFT FOR software floppy disk IDT4 V01 E 15 m IDT-IIIB RS-422 X-ray apparatus on-line X ONLINE SOFT FOR software floppy disk IDT4 V01 E FT100004.EPS TT100005.EPS 009-052-02 Installation-3 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
(3) [Remove] Additional board guide mark in the "Product abbreviation" column represents the cable length. TT100002.EPS Screw Equipment main unit FT100151.EPS NOTE Store the removed expansion board guide for later use. 009-052-01 Installation-4 FCR ID-T741 Service Manual 12.20.98 FM2370 (ITC)
Page 69
(5) Switch RS-422 and RS-232C using CH0 ~ CH2 on the SIF04A board. CH0 ~ CH2 correspond to the following connectors. CH0: CH-A CH1: CH-B CH2: CH-C When setting CH0 ~ CH2, confirm the interface (RS-422 and RS- 232C) between connected devices. 009-052-02 Installation-5 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
Page 70
(1) Mount the barcode reader on the bracket. (2) Turn the equipment upside down and set the bracket in position. (2) [Install] Bracket FT100164.EPS Screw x 2 (1) [Install] Barcode reader holder Screw x 2 Equipment FT100153.EPS 009-052-01 Installation-6 FCR ID-T741 Service Manual 12.20.98 FM2370 (ITC)
Page 71
Be sure that the employed anchor nuts conform to the wall conditions (use the supplied anchor nuts). 240.0 mm (4) [Connect] Cable Barcode reader holder FT100154.EPS 210.0 mm Wall-mounting bracket FT100157.EPS 009-052-01 Installation-7 FCR ID-T741 Service Manual 12.20.98 FM2370 (ITC)
Page 72
(5) Attach the bracket to the bottom surface of the IDT-IV. IDT-IV Wall-mounting bracket (6) [Install] IDT-IV Truss screw FT100160.EPS M4x8 x 2 [Install] Bracket Sems screw M3x4 x 4 FT100159.EPS 009-052-01 Installation-8 FCR ID-T741 Service Manual 12.20.98 FM2370 (ITC)
Page 73
(1) Attach the bracket to the bottom surface of the IDT-IV. IDT-IV Stand Knob (2) [Install] IDT-IV FT100166.EPS Truss screw M4x8 x 2 [Install] Bracket Sems screw M3x8 x 4 FT100165.EPS 009-052-01 Installation-9 FCR ID-T741 Service Manual 12.20.98 FM2370 (ITC)
(RMT-SLV) polarities, which must be connected correctly. • For equipment installation in the U.S., use cables that comply with the NEC725 DP-3/CL-2 requirements. RED/ RED/ Shield Shield 5 and 6: NC 7 and 8: NC FT100163.EPS 009-052-02 Installation-10 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
Rear of Retainer equipment Main switch REMOTE1 REMOTE2 RESET Power cable 100/120 V type 230 V type 240 V type Terminal Remote power supply cable FT100272.EPS FT100156.EPS 009-052-02 Installation-11 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
NOTE Ensure that the Caps Lock key is OFF. If it is ON, the relations between upper- and lower-case alphabetical letter entries are reversed. 009-052-01 Installation-12 FCR ID-T741 Service Manual 12.20.98 FM2370 (ITC)
Page 77
OS logon screen when you turn ON the power. Various setup procedures are to be performed in the maintenance mode during the installation process. 009-052-03 Installation-13 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
(4) and beyond. (4) Enter “fcr” as the user name. Hardware maintenance utility (5) Enter “fcr” as the password. Data conversion The entered password does not appear on the display. FT100009.EPS 009-052-03 Installation-14 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 79
(4) Touch [AC] to delete the default password for user’s service mode entry. The character string in the input area is then cleared. (5) Touch [123]. The upper-case alphabetical character input mode then pre- vails. 009-052-03 Installation-15 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
NOTE: If the machine is started up in step 8 or 9 without connecting the network cable, the communication cannot be established even if the cable is connected after startup. function is disabled. In such an instance, restart the system after connecting the cable. FT100049.EPS 009-052-02 Installation-16 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
(2) Prepare the floppy disk that contains the specific language menu 3.8.3 Adjusting the Setup Data as Needed for Individual Devices data file. Insert this disk into the floppy disk drive. FT100012.EPS 009-052-01 Installation-17 FCR ID-T741 Service Manual 12.20.98 FM2370 (ITC)
Page 82
FT100172.EPS (6) Touch [Finish]. (4) Select the language to be used, and then touch [Next]. You are returned to the “Maintenance process” menu screen. The setup type confirmation screen opens. FT100173.EPS 009-052-01 Installation-18 FCR ID-T741 Service Manual 12.20.98 FM2370 (ITC)
(4) Select “Install” and then touch [Next]. (2) Prepare the floppy disk that contains the optional software. The Setup type confirmation screen opens. Insert the disk into the floppy disk drive. FT100180.EPS 009-052-01 Installation-19 FCR ID-T741 Service Manual 12.20.98 FM2370 (ITC)
You are returned to the “Maintenance process” menu screen. The screen then shows nothing for a period of about 10 seconds. The installer starts and displays the Setup type selection screen. FT100175.EPS 009-052-01 Installation-20 FCR ID-T741 Service Manual 12.20.98 FM2370 (ITC)
Page 85
FT100176.EPS FT100174.EPS (5) Verify the settings and then touch [Next]. (7) Touch [Finish]. The Setup type confirmation screen opens. You are returned to the “Maintenance process” menu screen. FT100177.EPS 009-052-01 Installation-21 FCR ID-T741 Service Manual 12.20.98 FM2370 (ITC)
Concerning groups (IP information management group) and gate- ways (IP information gateway), see Maintenance, “3.4.3, IP registration information management/sharing function." From the “Maintenance process” menu screen, select [Network setup]. The “Network setup” screen opens. FT100023.EPS FT100022.EPS 009-052-02 Installation-22 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
Page 87
The system adds or changes the group information and then brings you back to the “Group information editing” screen. NOTE If you add group information, be sure to set up the host information for the added group. 009-052-02 Installation-23 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
Page 88
You are returned to the “Host information editing” screen. The [Ping] button is for confirming whether the device indicated on III. Enter the IP address. the "Host information addition" screen is properly connected up to the network. 009-052-04 Installation-24 FCR ID-T741 Service Manual 03.30.2000 FM2762 (ITC)
Page 89
Select a group that was set up as explained under “ Setting the group information”. FT1000237.EPS • IDC4-1 FT100282.EPS You are returned to the “Host information editing” screen. V. Enter a comment if necessary. FT1000238.EPS 009-052-02 Installation-25 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
Page 90
(1) While the “Network setup” screen displayed, select the host information to be deleted. (2) Touch [DELETE]. The confirmation message box opens. (3) Touch [Yes]. The selected host information is then deleted. 009-052-02 Installation-26 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
Page 91
Make your You are returned to the “Maintenance process” menu screen. selection from this list. You are returned to the “Group information editing” screen. 009-052-02 Installation-27 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
9000 Series IDT-IIIB image reader image reader FT100003.EPS FT100014.EPS NOTE On the “System setup” screen, do not set Intelligent HUB control to [ON] because this control function is not available at present. 009-052-02 Installation-28 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
Page 93
Leave the default (FCRIDT4) as it is. (3) Touch the [Protocols] tab. (4) Select “TCP/IP Protocol” and then Touch [Properties...]. FT100015.EPS FT100016.EPS 009-052-02 Installation-29 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
Page 94
Standard Time in the form of numerical data. For this reason, discrepancies in the time will result if the time zones for IDT-IV and IDC- IV units are different. FT100020.EPS FT100017.EPS You are returned to the “System setup” screen. 009-052-02 Installation-30 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
Page 95
(2) Set the keyboard type and then touch [OK]. For English version: Ensure that “PC/AT Enhanced Keyboard (101/102-Key)” is selected. FT100018.EPS You are returned to the “System setup” screen. FT100019.EPS You are returned to the “System setup” screen. 009-052-02 Installation-31 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
Page 96
You are returned to the “System setup” screen. IMPORTANT Do not disable the screen saver. Although the BIOS provides LCD backlight ON/OFF control, the backlight OFF feature does not successfully save the LCD from “burnout”. 009-052-02 Installation-32 FCR ID-T741 Service Manual 3.30.99 FM2483 (ITC)
(2) Make the network cable connection to each slave IDT unit. (3) Press the sub-switch to start the equipment. An error occurs during application startup, causing the appli- cation to quit. Leave it as is. 009-052-02 Installation-33 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
3.6 Restarting the Slave IDT Restart all the slave IDT units by turning the sub-switch OFF and then back ON. The maintenance mode starts. FT100234.EPS (3) Touch [DELIVERY]. The delivery execution confirmation screen opens. 009-052-02 Installation-34 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
The “Serial port” screen opens. The magnetic card reader is automatically set up. From the “Maintenance process” menu screen, select [Hookup device setup]. The “Hookup device setup” screen opens. FT100028.EPS FT100027.EPS 009-052-02 Installation-35 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
Page 100
You are returned to the “Serial port” screen. (2) Touch [OK]. You are returned to the “Hookup device setup”s screen. FT100027.EPS The “IR targeted for image processing parameter update” screen opens. 009-052-04 Installation-36 FCR ID-T741 Service Manual 03.30.2000 FM2762 (ITC)
Page 101
Sets to [OFF] for 9000 series image readers. • PEM These image processing parameters are for granularity suppression and sharpness enhancement processing exclu- sively for mammography. Set to [OFF] for 9000 series image readers. 009-052-03 Installation-37 FCR ID-T741 Service Manual 9.24.99 FM2561-1 (ITC)
III. Enter the values of the barcode data to be read. (3) Touch [OK]. FT100030.EPS The system changes the barcode format and returns you to the “Barcode setup” screen, (4) Touch [Close]. You are returned to the “Maintenance process” menu screen. 009-052-03 Installation-38 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
(2) Specify whether or not to use a hospital card in addition to the Fuji card. When using a hospital card, complete the procedure set forth FT100032.EPS under “ Defining the magnetic card format”. 009-052-02 Installation-39 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
Page 104
When using a hospital card, define its format by performing the data type change/addition/deletion procedure. “Appendix 1, ID Card Data Format” From the “Magnetic card setup” screen, touch [Card definition]. The “Magnetic card format” screen opens. FT100035.EPS FT100034.EPS 009-052-02 Installation-40 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
Page 105
You are returned to the “Data field setup” screen. An error message appears. In this instance, touch [OK] and repeat steps I and beyond. (3) Touch [Close]. You are returned to the “Magnetic card setup” screen. 009-052-03 Installation-41 FCR ID-T741 Service Manual 9.24.99 FM2561-1 (ITC)
Page 106
To delete an entered character, place the cursor over it and then press the space bar. (3) Touch [OK]. You are returned to the “Magnetic card setup” screen. (4) Touch [Close]. You are returned to the “Maintenance process” menu screen. 009-052-02 Installation-42 FCR ID-T741 Service Manual 2.20.99 FM2434 (ITC)
I. Turn [ON] or [OFF] the “Menu Coordination” feature. To effect processing mode changeover in coordination with an IP withdrawal button exposure menu selection, touch [ON]. FT100288.EPS II. Select a selector button to define. 009-052-03 Installation-43 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
II. Because this setup is effective only for Japanese magazine- type image reader, leave this column OFF. Selector button FT100038.EPS If there is only one selector button (ex.: IP only), it will not be displayed. 009-052-04 Installation-44 FCR ID-T741 Service Manual 03.30.2000 FM2762 (ITC)
Page 109
Select [Main]. The [Main/Sub] setup is effective only for Japanese. [Main] will be automatically selected if the full name in kanji from step I is selected with the kanji menu input [OFF]. 009-052-04 Installation-45 FCR ID-T741 Service Manual 03.30.2000 FM2762 (ITC)
• 15JAN1980: EUROPEAN long date (No separator) • S550115: JAPANESE date (No separator) • 800115: ANSI short special • 3550115: JAPANESE short special date (No separator) • S.55.01.15: JAPANESE short special date 009-052-03 Installation-46 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
The DICOM interface can use the STUDYInstanceUID information. For whether other interfaces can use the STUDYInstanceUID or not, it depends on the equipment and/or software version, requiring thus confirmation for each interface. TT100010.EPS 009-052-03 Installation-47 FCR ID-T741 Service Manual 9.24.99 FM2561-1 (ITC)
Page 112
IDT-IV can fully issue all UIDs. • The STUDY will be split into two if the ExamDate is not just one because exposure extends over 0:00AM. TT100011.EPS 009-052-03 Installation-48 FCR ID-T741 Service Manual 9.24.99 FM2561-1 (ITC)
Page 113
Basically, the limit numbers of characters used in the Fuji system apply. However, if complete information can be transmitted to the UID issuing devices, the limits to be applied will be as listed in the table above. TT100012.EPS 009-052-03 Installation-49 FCR ID-T741 Service Manual 9.24.99 FM2561-1 (ITC)
Page 114
After setting the UID Issue to ON, set the UID issue system. type for the entire system. • UID Issue Type Touch the UID Issue Type button. The “UID Issue Type Setup” screen opens. 009-052-03 Installation-50 FCR ID-T741 Service Manual 9.24.99 FM2561-1 (ITC)
Page 115
FCR5000, E-i/f-connected HIC, etc.) series. are used mixed with new-type devices because this type can be specified only in the ID-T741. A series of exposure grouped into examination menu can also be handled as one series, and it is possible to specify...
I. Touch the button in the “IP logical size” column. The “IP logical size” screen opens. Select the size to be used. NOTE The logical size is “18 x 43” for the FCR5000 and “T Magazine” for Toshiba cassetteless units. 009-052-03 Installation-52 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 117
FT100231.EPS You are returned to the “Exposure menu parameter environment setup” screen. FT100230.EPS You are returned to the “Exposure menu parameter envi- ronment setup” screen. 009-052-03 Installation-53 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 118
[Parameter display setup]. Select a mode. The “Parameter display setup” screen opens. Auto/Semi/Fix and Semi-X Auto/Semi/Fix, Semi-X, and MANUAL FT100233.EPS You are returned to the “Exposure menu parameter FT100240.EPS environment setup” screen. 009-052-03 Installation-54 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 119
[Parameter display setup]. The “Parameter display setup” screen opens. (2) From the “Parameter display setup” screen, touch [Routine processing]. The “Routine process parameter button display setup” screen opens. Parameter button FT100289.EPS 009-052-03 Installation-55 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 120
: Film mark (on-film exposure-direction marking characters such as AP and PA) : IP logical size (size selection for logical reading) : Filing mode (image recording on the ODF) : Function (special processing performed depending on the 009-052-03 Installation-56 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
The two designated parameter buttons switch their display positions. (4) Touch [Close]. You are returned to the “Exposure menu parameter environ- ment setup” screen. (5) Touch [OK]. You are returned to the “Maintenance process” menu screen. 009-052-03 Installation-57 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
“3.7.9 Backing up the setup data.” Insert the disk into the floppy disk drive. (5) Touch [EXECUTION]. The backup process starts. The “Process Completed” screen opens. (6) Touch [OK]. FT100043.EPS You are returned to the “Maintenance process” menu screen. 009-052-03 Installation-58 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
“3.7.5 Setting the operating environment” • Data format setup “3.7.6 Setting the data formats” • Exposure menu parameter setup “3.7.8 Setting the exposure menu parameters” • Option setup “3.7.9 Setting the optional functions” 009-052-03 Installation-59 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
This is valid when the RIS connection mode is [Type B] connection or [IDC4]. Default (30 sec.) should be left as it is. IV. Select the appropriate “Single Byte Character Code” system. FT100169.EPS 009-052-03 Installation-60 FCR ID-T741 Service Manual 9.24.99 FM2561-1 (ITC)
Page 125
I. Specify the channel to be connected, and then select [ON]. You are returned to the “Patient information on-line function setup” screen. (3) Touch [OK]. You are returned to the “Maintenance process” menu screen. 009-052-04 Installation-61 FCR ID-T741 Service Manual 03.30.2000 FM2762 (ITC)
I. Specify whether or not to transmit the exposure condition data. II. Specify whether or not to receive the implementation condi- tion data. (2) Touch [OK]. You are returned to the “Maintenance process” menu screen. 009-052-03 Installation-62 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
(4 lower digits) (14 digits) (FUJI) (20 digits) — Digit Birth date Number Content (10 digits) Male/Female Year • Month • ("•" denotes a period.) Digit — Undefined (22 digits) Content (space: 20H) 009-052-03 Installation-63 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 128
— Digit Digit — — Alphanumeric Alphanumeric department Undefined department Distribution code Undefined Content Content name (8 digits) Test number (10 digits) (4 digits) name (8 digits) (6 digits) (8 digits) 009-052-03 Installation-64 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 129
Digit – – Digit – – Distribution code Undefined Department name in English Department name in Kanji Test number Content Content (8 digits) (4 digits) (8 digits) (8 digits) (10 digits) 009-052-03 Installation-65 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 130
64 65 66 67 — 74 75 76 77 78 Alphanumeric department Distribution code Test number Space Digit — Content name (8 digits) (10 digits) (2 digits) (8 digits) Undefined Content (28 digits) 009-052-03 Installation-66 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 131
If the number of digits for the birth date falls short of its effective number of digits, enter numbers from the right-most location, and fill the rest with zero (JIS: 30H/ISO: 10H). 009-052-03 Installation-67 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 132
For a card with the Standard Format, the undefined area cannot be used. Use space code (JIS: 20H/ISO: 00H) for the undefined area. To use this area for a special purpose, change the system code from the Standard format to another. 009-052-03 Installation-68 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 133
LRC: LRC Code LRC denotes a horizontal redundancy code for a horizontal parity check bit of information characters recorded. Horizontal parity check is performed from the start code to the end code. 009-052-03 Installation-69 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Touch “Hardware maintenance utility” on the “Maintenance pro- cess” menu screen. The “IDT-4 Function Tester” screen appears. FT100363.EPS The type of the magnetic card reader installed and the “MCR” dialog appear. FT100350.EPS 009-052-03 Installation-70 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 135
“MCR” dialog. (3) Touch [Exit]. FT100352.EPS You are returned to the “IDT-4 Function Tester” screen. FT100351.EPS When re-checking the magnetic card reader, touch another menu tab and then touch the “MCR” tab. 009-052-03 Installation-71 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 136
(3) Touch [Exit]. FT100353.EPS You are returned to the “IDT-4 Function Tester” screen. The “BCR” dialog will appear. When re-checking the barcode reader, touch another menu tab and then touch the “BCR” tab. 009-052-03 Installation-72 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 137
The following screens appear sequentially in this order. FT100359.EPS After a while, you are returned to the “IDT-4 Function Tester” screen. When re-checking the LCD, touch another menu tab and then touch the “LCD” tab. FT100357.EPS 009-052-03 Installation-73 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 138
[Apply]. FT100376.EPS The buzzer will sound for a few seconds. When re-checking the Buzzer, touch another menu tab and then touch the “Buzzer” tab. FT100360.EPS The “Touch Panel Driver” dialog appears. 009-052-03 Installation-74 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 139
• Do not place anything on the LCD panel. FT100361.EPS FT100362.EPS The “TestResult” dialog appears. You are returned to the “IDT-4 Function Tester” screen. When re-checking the touch panel, touch another menu tab and then touch the “Touch” tab. 009-052-03 Installation-75 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 140
Do not change values. IP address input column FT100366.EPS FT100365.EPS Check results (“OK” or “NG”) appears. When re-checking the SIF04A board, touch another menu tab and then touch the “SIF04A” tab. 009-052-03 Installation-76 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 141
The check screen appears. FT100368.EPS (3) Touch [OK]. You are returned to the “IDT-4 Function Tester” screen. When re-checking communications with the IDT-IV, touch an- other menu tab and then touch the “Network” tab. 009-052-03 Installation-77 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 142
After the FDD has been checked, its results appear on the left top of the screen. (3) Remove the FD from the FDD. When re-checking the FDD, touch another menu tab and then touch the “FDD” tab. 009-052-03 Installation-78 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 143
(3) Touch <Enter> key. You are returned to the “IDT-4 Function Tester” screen. When re-checking the keyboard, touch another menu tab and then touch the “KB” tab. FT100372.EPS The “Keyboard Test” dialog appears. 009-052-03 Installation-79 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 144
FT100374.EPS You are returned to the “IDT-4 Function Tester” screen. The “Date/Time Properties” screen appears. When re-checking the date and time, touch another menu tab and then touch the “RTC” tab. 009-052-03 Installation-80 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
H drive : Drive of “Ramzou” data area FT100700.EPS 1. Enter “h:” and press the <Enter> key. The “Convert Prepare” screen will appear. The current directory will be changed to the H drive. 009-052-03 Installation-81 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 146
III. Touch the “Convert Type.” • Data\Udata\S_deftbl.dat : Converts all menus. • Data\Udata\Mpmidxs.prm • Data\Udata\Mpmsel.prm : Converts only the IP reading size and the IP • Data\Udata\Dspgtb.prm reading position. • Data\Udata\K_menu.prm • Data\Udata\K_bui.prm 009-052-03 Installation-82 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 147
FT100703.EPS The “Data Conversion” result list screen will appear. 2. Touch [Close]. FT100705.EPS The “Conversion Completed Normally.” screen will appear. FT100704.EPS The display will return to the “Maintenance Processing” menu screen. 009-052-03 Installation-83 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)
Page 148
Touching [No] on the “Conversion Completed Normally” screen will not activate the converted menu and the display will return to the “Maintenance Processing” menu screen. (5) Remove the DataFD from the FDD. 009-052-03 Installation-84 FCR ID-T741 Service Manual 9.24.99 FM2561 (ITC)