Husqvarna 535FBX Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Brush Cutter
  5. 535FBX
  6. Operator's manual

Husqvarna 535FBX Operator's Manual

Hide thumbs Also See for 535FBX:
Table of Contents

Advertisement

Quick Links

Download this manual
535FBX, TA1100
EN
Operator's manual
2-41

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 535FBX

Summary of Contents for Husqvarna 535FBX

  • Page 1 535FBX, TA1100 Operator's manual 2-41...

  • Page 2: Table Of Contents

    Contents Introduction 535FBX............2 Declaration of Conformity 535FBX....... 32 Safety 535FBX..............4 Introduction TA1100............. 34 Assembly 535FBX............10 Safety TA1100.............. 35 Operation 535FBX............14 Assembly TA1100............37 Maintenance 535RBX...........18 Operation TA1100............38 Troubleshooting............27 Technical data TA1100..........39 Transportation and storage...........28 Accessories ..............39 Technical data 535FBX..........
  • Page 3 To prevent injury Technical of the product is specified in to the operator or bystanders, read data 535FBX on page 28 and on the and obey all safety instructions in the label. operator's manual. Please read the operator's manual The product agrees with the applicable EC directives.

  • Page 4: Safety 535Fbx

    Product liability As referred to in the product liability laws, we are not liable for damages that our product causes if: Safety 535FBX Safety definitions medical implants. To reduce the risk of serious or fatal injury we recommend persons with medical...
  • Page 5 particles that nay be carcinogenic. Avoid being • Never use the machine indoors or in spaces lacking exposed to these compounds when handling the proper ventilation. Exhaust fumes contain carbon muffler and /or spark arrester. Prior to any handling monoxide, an odourless, poisonous and highly of the muffler and/or the spark arrester, refer to dangerous gas.
  • Page 6 • If the safety devices are defective, speak to your decreases the degree of injury if an accident does Husqvarna servicing dealer. occur. Let your dealer help you select the right equipment. To do a check of the throttle trigger lockout •...
  • Page 7 2. Release the throttle trigger lockout and make sure 2. Move the stop switch to the stop position and make that the throttle control is locked at idle speed. sure that the engine stops. 3. Push the throttle trigger lockout and make sure that it To do a check of the vibration damping system goes back to its initial position when you release it.
  • Page 8 b) Make sure that the spark arrestor mesh is attached correct. The muffler keeps noise levels to a minimum and sends exhaust fumes away from the operator. For mufflers it is Fuel safety very important that you follow the instructions on how to check, maintain and service your product.
  • Page 9 • Make sure that a leak cannot occur when you move saw chain that is damaged or incorrectly sharpened the product or fuel container. increases the risk of accidents. • Do not put the product or a fuel container where there is an open flame, spark or pilot light.

  • Page 10: Assembly 535Fbx

    Assembly 535FBX To assemble the engine to the frame To assemble the two-piece shaft 1. Assemble the engine and the frame with the bolt. 1. Turn the knob to loosen the coupling. Make sure that the heel is put on the correct side of 2.
  • Page 11 To disassemble the two-piece shaft To assemble the bar and chain 1. Turn the knob 3 turns or more to loosen the 1. Unscrew the bar nut and remove the protective coupling. cover. 2. Fit the bar over the bar bolt. Place the bar in its rearmost position.
  • Page 12 6. The chain is correctly tensioned when it does not 3. Adjust the backplate to the correct height. Make sure sag from the underside of the bar, but can still be that the pin aligns with 1 of the holes on the frame. turned easily by hand.
  • Page 13 To set the product in transport position 5. Adjust the shoulder strap until the weight is equal on your shoulders. 1. Loosen the knob and remove the top part of the load reducer. To set the work height 1. Pull out the cord to the necessary work length and make a knot.

  • Page 14: Operation 535Fbx

    6. Pull the attachment straight out of the coupling. 7. Install the shaft to the knob on the frame. 9. Hang the throttle hand guard on the frame. Operation 535FBX Introduction 6. Check that the saw chain always stops when the engine is idling.
  • Page 15 1. Clean the area around the fuel tank cap. • If Husqvarna two-stroke oil is not available, use a 2. Shake the container and make sure that the fuel is two-stroke oil of good quality for air-cooled engines.
  • Page 16 27 . better control over where they fall. • Use Husqvarna chain oil for maximum saw chain life and to minimise environmental damage. If Husqvarna chain oil is not available, we recommend you to use a standard chain oil.
  • Page 17 WARNING: Read the warning instructions in the safety chapter before you Safety 535FBX on start the product (refer to page 4 ). 1. Use protective gloves. 2. Hold the body of the product on the ground with your left hand.

  • Page 18: Maintenance 535Rbx

    10. Operate the throttle gradually. when assembling, checking and/or maintenance is done. 11. Make sure the engine runs smoothly. Forestry clearing Note: If the engine stops, do the procedure again. General work instructions To stop the product WARNING: Be careful when you cut a 1.
  • Page 19 3. Adjust the idle speed with the idle adjustment screw T which is identified with "T" mark. Turn the idle Note: Technical data 535FBX on page 28 Refer to adjustment screw clockwise until the saw chain starts to turn.
  • Page 20 5. Push the throttle cam with your finger. • wear gloves; • clean and/or service in a well ventilated area; • do not use pressurized air to clean the spark arrester screen; • use a steel brush and brush away from your body when cleaning the spark arrester.
  • Page 21 To examine the spark plug CAUTION: Always use the recommended spark plug type, refer to Technical data 535FBX on page 28 . 2. Lubricate the drive shaft. Incorrect spark plug type can cause damage to the product. • Examine the spark plug if the engine is low on power, is not easy to start or does not operate correctly at idle speed.
  • Page 22 4. Align the hole in the drive shaft sleeve with the knob 6. Do a check of the rubber sealing surface. Replace on the clutch cover. the filter on the rubber seal if it is damaged. 7. Make sure that the filter is dry before you assemble Two piece-shaft Apply grease to the end of the drive shaft after each 30 hours of operation.
  • Page 23 Replace a worn or damaged guide bar or saw chain with 3. Clean the groove in the guide bar. the guide bar and saw chain combination recommended by Husqvarna. This is necessary to keep the safety Accessories on functions of the product. Refer to page 39 , for a list of replacement bar and chain combinations that we recommend.
  • Page 24 General information about how to sharpen the • Chain pitch, in. The distance between the drive links of the saw chain must align with the distance of the cutters teeth on the bar tip sprocket and drive sprocket. Do not use a blunt saw chain. If the saw chain is blunt, you must apply more pressure to push the guide bar through the wood.
  • Page 25 It is not easy to sharpen a saw chain correctly without difference in height between the two gives the cutting the correct equipment. Use Husqvarna file gauge. This depth (depth gauge setting). will help you to keep maximum cutting performance.
  • Page 26 1. Use a flat file and a depth gauge tool to adjust the depth gauge setting. Only use Husqvarna depth gauge tool to get the correct depth gauge setting and bevel for the depth gauge.

  • Page 27: Troubleshooting

    The spark plug electrode gap is in- Clean the spark plug. Make sure that correct. the electrode gap is correct, refer to Technical data 535FBX on page 28 . Make sure that the spark plug has a supressor. The spark plug is loose.

  • Page 28: Transportation And Storage

    • When the product is no longer in use, send it to To prepare your product for long-term a Husqvarna dealer or discard it at a recycling location. storage 1. Stop the product and let it become cool before you disassemble it.
  • Page 29 Speed-regulated ignition system Ignition system Spark plug Champion RCJ 6Y Electrode gap, mm Fuel and lubrication system Fuel tank capacity, litre/cm 0.6/600 Oil tank capacity, litre/cm 0.26/260 Weight Without fuel, cutting attachment, kg 12.4 Noise emissions Sound power level, measured dB (A) Sound power level, guaranteed dB (A) Sound levels Equivalent sound pressure level at the operator’s ear, measured according to ISO 22868, dB(A):...

  • Page 30: Accessories

    If you do not know which saw chain you have on your product, turn to your servicing dealer. Husqvarna file gauge gives you the correct filing angles. We recommend you to always use a Husqvarna file gauge to restore the sharpness of the saw chain. The part numbers are given in the table below.
  • Page 31 Approved attachments Use with Pole saw attachment PAX1100 535FBX 1301 - 006 - 31.10.2022...

  • Page 32: Declaration Of Conformity 535Fbx

    Declaration of Conformity 535FBX EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Pole saw Brand Husqvarna Type / Model 535FBX Identification Serial numbers dating from 2022 and onwards...
  • Page 33 Declaration of conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Pole saw Husqvarna Brand Type / Model 535FBX Identification Serial numbers dating from 2022 and onwards complies fully with the following UK regulations:...

  • Page 34: Introduction Ta1100

    Introduction TA1100 Symbols on the product Keep a minimum of 15 m distance to persons and animals during operation of WARNING! This product is dangerous. the product. Injury or death can occur to the operator or bystanders if the product is not used carefully and correctly.

  • Page 35: Safety Ta1100

    Product overview TA1100 1. Trimmer head 7. Loop handle 2. Grease filler cap, bevel gear 8. Operator's manual 3. Bevel gear 9. Hex key 4. Cutting attachment guard 10. Locking pin 5. Shaft 11. Drive disc 6. Handle adjustment Safety TA1100 Safety instructions for operation •...
  • Page 36 operator does work in the same area, keep a safety • Stop the engine before you move to a new work distance of a minimum of 2 times the tree height and area. Always attach the transport guard before you a minimum of 15 m/50 ft.

  • Page 37: Assembly Ta1100

    Trimmer head • Only use recommended trimmer heads and trimmer lines. Always make WARNING: • Only use recommended cutting attachments. • Smaller machines requires small trimmer heads and sure the trimmer line is vice versa. wound tightly and evenly • The length of the trimmer line is important.

  • Page 38: Operation Ta1100

    7. Turn the trimmer head /plastic blades (H) in the opposite direction from which the trimmer head/ plastic blades rotates. Operation TA1100 Grass trimming with a trimmer head To cut the grass 1. Make sure that the trimmer line is parallel to the To trim the grass ground when you cut the grass.

  • Page 39: Technical Data Ta1100

    3. Move the trimmer head from side to side and sweep line to prevent unbalance and vibrations in the grass. the handles. Also do a check of the other parts of the trimmer head and clean it if necessary. WARNING: Clean the trimmer head cover each time you assemble new trimmer Technical data TA1100...

  • Page 40: Declaration Of Conformity Ta1100

    Declaration of Conformity TA1100 EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Pole saw Brand Husqvarna Type / Model TA1100 Identification Serial numbers dating from 2022 and onwards...
  • Page 41 Declaration of conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Pole saw Husqvarna Brand Type / Model TA1100 Identification Serial numbers dating from 2022 and onwards complies fully with the following UK regulations:...
  • Page 42 1301 - 006 - 31.10.2022...
  • Page 43 1301 - 006 - 31.10.2022...
  • Page 44 Original instructions 1142909-26 2022-11-08...

This manual is also suitable for:

Ta1100

Table of Contents