Table of Contents
Advertisement
Section
Operating this unit
02
03
! You need to activate the AUX setting in the
initial setting menu. Refer to AUX1 (front
AUX input setting)/AUX2 (rear RCA input set-
ting) on the previous page.
1
Insert the mini plug into the AUX input
jack on this unit.
For more details, refer to Head unit on page 3.
This auxiliary device is automatically set to
AUX1.
2
Press SRC to select AUX1 as the source.
AUX2 source
When connecting an auxiliary device using the
rear audio input
! You need to activate the AUX setting in the
initial setting menu. Refer to AUX1 (front
AUX input setting)/AUX2 (rear RCA input set-
ting) on the previous page.
1
Use the rear RCA input to connect an aux-
iliary device featuring RCA output.
For more details, refer to Power cable connection
on page 20.
This auxiliary device is automatically set to
AUX2.
# This type of connection can only be made if the
auxiliary device has RCA outputs.
2
Press SRC to select AUX2 as the source.
Using an AUX source
For South American, Oceanian, Middle East
Asian, South African models
1
Insert the stereo mini plug into the AUX
input jack.
For more details, refer to Head unit on page 3.
2
Press SRC to select AUX as the source.
18
En
Notes
! This model accepts audio signal input only.
! AUX cannot be selected unless the auxiliary
setting is turned on. For more details, refer to
AUX (auxiliary input) on the previous page.
Switching the dimmer setting
You can adjust the brightness of illumination.
% Press and hold
.
Turning the clock display on
or off
% Press
to turn the clock display on or
off.
# The clock display disappears temporarily when
you perform other operations, but the clock display
appears again after 25 seconds.
Connections
WARNING
! To avoid the risk of accident and the potential
violation of applicable laws, no viewing of
front seat video should ever occur while the
vehicle is being driven. Also, rear displays
should not be in a location where they are
visibly distracting to the driver.
! In some countries or states the viewing of im-
ages on a display inside a vehicle even by
persons other than the driver may be illegal.
Where such regulations apply, they must be
obeyed and this unit's DVD features should
not be used.
CAUTION
! PIONEER does not recommend that you in-
stall or service your display unit yourself. In-
stalling or servicing the product may expose
you to risk of electric shock or other hazards.
Refer all installation and servicing of your
display unit to authorized Pioneer service
personnel.
! Secure all wiring with cable clamps or elec-
trical tape. Do not allow any bare wiring to re-
main exposed.
! Do not drill a hole into the engine compart-
ment to connect the yellow cable of the dis-
play unit to the vehicle battery. Engine
vibration may eventually cause the insulation
to fail at the point where the wire passes
from the passenger compartment into the
engine compartment. Take extra care in se-
curing the wire at this point.
! It is extremely dangerous to allow the display
lead to become wound around the steering
column or shift lever. Be sure to install the
display in such a way that it will not obstruct
driving.
! Make sure that wires will not interfere with
moving parts of the vehicle, such as the shift
lever, parking brake or seat sliding mecha-
nism.
! Do not shorten any cables. If you do, the pro-
tection circuit may fail to work properly.
WARNING
! Use speakers over 50 W (output value) and
between 4 W to 8 W (impedance value). Do
not use 1 W to 3 W speakers for this unit.
! The black cable is ground. When installing
this unit or power amp (sold separately),
make sure to connect the ground wire first.
Ensure that the ground wire is properly con-
nected to metal parts of the car's body. The
ground wire of the power amp and the one of
this unit or any other device must be con-
nected to the car separately with different
screws. If the screw for the ground wire loos-
ens or falls out, it could result in fire, genera-
tion of smoke or malfunction.
POWER AMP
Ground wire
Other devices
Metal parts of car's body
(Another electronic
device in the car)
Important
! When installing this unit in a vehicle without
an ACC (accessory) position on the ignition
switch, failure to connect the red cable to the
terminal that detects operation of the ignition
key may result in battery drain.
ACC position
No ACC position
Hide quick links:
Advertisement
Table of Contents
