Setting Up The Dvd Player - Pioneer DVH-345UB Owner's Manual

Section
Operating this unit
02
FAD/BAL (fader/balance adjustment)
1 Press M.C. to display the setting mode.
2 Press M.C. to cycle between fader (front/rear)
and balance (left/right).
3 Turn M.C. to adjust speaker balance.
PRESET EQ (equalizer recall)
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the equalizer.
DYNAMIC—VOCAL—NATURAL—CUSTOM
—FLAT—POWERFUL
! You can also switch the equalizer by pressing
repeatedly.
TONE CTRL (equalizer adjustment)
! Adjusted equalizer curve settings are stored in
CUSTOM.
1 Press M.C. to display the setting mode.
2 Press M.C. to select BASS (bass)/MID (mid)/
TREBLE (treble).
3 Turn M.C. to adjust the level.
Adjustment range: +6 to -6
LOUD (loudness)
Loudness compensates for deficiencies in the low-
frequency and high-frequency ranges at low vol-
ume.
1 Press M.C. to select the desired setting.
OFF (off)—LOW (low)—HI (high)
SUB.W (subwoofer on/off setting)
This unit is equipped with a subwoofer output
which can be turned on or off.
1 Press M.C. to select the desired setting.
NOR (normal phase)—REV (reverse phase)—
OFF (subwoofer off)
SUB.W CTRL (subwoofer adjustment)
14
En
The cut-off frequency and output level can be ad-
justed when the subwoofer output is on.
Only frequencies lower than those in the selected
range are outputted from the subwoofer.
! When you select OFF in SUB.W, you cannot se-
lect this function. For details, refer to SUB.W
(subwoofer on/off setting) on this page.
1 Press M.C. to display the setting mode.
2 Press M.C. to cycle between the cut-off fre-
quency and output level of the subwoofer.
Cut-off frequency (Cut-off frequency display
flashes.)—Output level (Output level display
flashes.)
3 Turn M.C. to select the desired setting.
Cut-off frequency: 50HZ—63HZ—80HZ—
100HZ—125HZ
Output level: –24 to +6
SLA (source level adjustment)
SLA (Source level adjustment) lets you adjust the
volume level of each source to prevent radical
changes in volume when switching between sour-
ces.
! Settings are based on the FM volume level,
which remains unchanged.
! When selecting FM as the source, you cannot
switch to SLA.
! The AM volume level can also be adjusted with
this function.
1 Press M.C. to display the setting mode.
2 Turn M.C. to adjust the source volume.
Adjustment range: +4 to –4
Operating this unit

Setting up the DVD player

Introduction of DVD setup
adjustments
You can use this menu to change audio, subtitle,
parental lock and other DVD settings.
1 Select DVD as the source and then press g.
2 Press MENU when the disc is stopped.
The DVD setup menu is displayed.
3 Move the thumb pad left or right to switch the
DVD setup menu categories.
LANG. (language)—PICT. (picture)—GEN.
(general)
4 Move the thumb pad up or down to select the
DVD setup function names.
For LANG.: SUBTITLE LANG. (subtitle lan-
guage settings)—AUDIO LANG. (audio lan-
guage settings)—MENU LANG. (menu
language settings)—OSD LANGUAGE (on
screen display language setting)—CHARAC-
TER SET (character set setting)
For PICT.: ANGLE ICON DISPLAY (angle icon)
—TV ASPECT (TV aspect)—SLIDESHOW TIME
(slideshow interval time setting)
For GEN.: PARENTAL (parental lock)—DivX
SUBTITLE (DivX/MPEG-4 subtitle)—DivX VOD
(DivX VOD)
Note
If you press MENU during display of a DVD
setup menu, the DVD setup menu is canceled
and the unit returns to the previous display.
Menu operations identical for
DVD setup adjustments
Returning to the previous display
1 Press RETURN.
Setting the subtitle language
You can set a desired subtitle language. When
available, the subtitles will be displayed in the se-
lected language.
1 Move the thumb pad up or down to select
SUBTITLE LANG. in LANG.
2 Click the thumb pad.
A subtitle language menu is displayed.
3 Move the thumb pad up, down, left or right to
select the desired language.
4 Click the thumb pad.
The subtitle language is set.
Notes
! If the selected language is not available, the
language specified on the disc is displayed.
! You can also switch the subtitle language by
pressing SUBTITLE during playback. (Refer
to Changing the subtitle language during play-
back (Multi-subtitle) on page 11.)
! The setting made here will not be affected
even if the subtitle language is switched dur-
ing playback using SUBTITLE.
When you select OTHERS
A language code input display is shown when
OTHERS is selected. Refer to Language code chart
for DVD on page 29.
1 Pressing CLEAR cancels the input numbers.
Setting the audio language
1 Move the thumb pad up or down to select
AUDIO LANG. in LANG.
2 Click the thumb pad.
An audio language menu is displayed.
3 Move the thumb pad up, down, left or right to
select the desired audio language.
4 Click the thumb pad.
The audio language is set.