Related Manuals for Dahua IPC-HFW5442HN-ZHE
Summary of Contents for Dahua IPC-HFW5442HN-ZHE
- Page 1 Model H IR Bullet Network Camera Quick Start Guide ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.1...
-
Page 2: Foreword
Quick Start Guide Foreword General This manual introduces the functions, installation, and operations of the camera. Safety Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury. - Page 3 Quick Start Guide occurred when using the device. If there is any uncertainty or controversy, please refer to our final explanation. ...
-
Page 4: Important Safeguards And Warnings
Quick Start Guide Important Safeguards and Warnings Electrical Safety All installation and operation shall conform to your local electrical safety codes. The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supply power with rated voltage which conforms to Limited Power Source requirement according to IEC60950-1. Note that the power supply requirement is subject to the device label. - Page 5 Quick Start Guide It is recommended to ground the device to enhance reliability. Do not touch the image sensor (CMOS) directly. Dust and dirt can be removed with air blower, or you can wipe the lens gently with soft cloth that is moistened with alcohol. You can clean the device body with soft dry cloth, and for stubborn stains, use the cloth with mild ...
-
Page 6: Table Of Contents
Quick Start Guide Table of Contents Foreword ................................I Important Safeguards and Warnings ......................III 1 Introduction ..............................1 Device Ports ....................................1 Connecting Alarm Input/output ............................2 2 Network Configuration ..........................4 Initializing Device ..................................4 Modifying Device IP Address ..............................5 Logging in to Web Interface.............................. -
Page 7: Introduction
Quick Start Guide Introduction Device Ports Device ports might vary with different models, and the actual product shall prevail. Waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit and water damage. For the detailed operations, see the FAQ Manual. Figure 1-1 Device ports For more information about device ports, see Table 1-1. -
Page 8: Connecting Alarm Input/Output
Quick Start Guide Port Name Description Inputs 12V DC power. Be sure to supply power as instructed in the manual. DC 12V Device abnormity or damage could occur if power is not supplied correctly. Connecting Alarm Input/output Alarm input/output is available on select models. Step 1 Connect alarm input device to the alarm input end of the I/O port. - Page 9 Quick Start Guide Figure 1-3 Mode A Figure 1-4 Mode B Figure 1-5 Mode C Step 3 Log in to web interface, and configure alarm input and alarm output in alarm setting. The alarm input on the web interface is corresponding to the alarm input end of the I/O ...
-
Page 10: Network Configuration
Quick Start Guide Network Configuration Device initialization and IP address setting can be finished with the "ConfigTool" or on web interface. For more information, see the Web Operation Manual. Device initialization is available on select models, and it is required at first use or after the device ... -
Page 11: Modifying Device Ip Address
Quick Start Guide The Device initialization interface is displayed. Select the devices that need initialization, and then click Initialize. Step 6 The password setting interface is displayed. See Figure 2-2. Figure 2-2 Password setting Step 7 Set and confirm the password of the devices, then enter a valid email address, and then click Next. -
Page 12: Logging In To Web Interface
Quick Start Guide After clicking Search setting, enter the username and password, and make sure that they are the same as what you set during initialization; otherwise there will be wrong password notice. Select the devices whose IP addresses need to be modified, and then click Modify IP. Step 2 The Modify IP Address interface is displayed. - Page 13 Quick Start Guide Figure 2-4 Main interface...
-
Page 14: Installation
Quick Start Guide Installation Packing List The tool required for the installation such as electric drill is not provided in the packing. The operation manual and related tool are contained in the disk or the QR code, and the actual ... -
Page 15: Installing Device
Quick Start Guide Installing Device 3.3.1 Installation Type 3.3.2 Installing SD Card (Optional) Disconnect the power before installing or removing the SD card. Press and hold the reset button for 10 s to reset the camera. 3.3.3 Threading Cable This section takes threading network cable for example. -
Page 16: Attaching Device
Quick Start Guide 3.3.4 Attaching Device Make sure that the mounting surface is strong enough to hold at least three times of the weight of the device and bracket. - Page 17 Quick Start Guide Cable going through the mounting surface Cable going through the side cable tray...
-
Page 18: Wrapping Waterproof Tape (Optional)
Quick Start Guide 3.3.5 Wrapping Waterproof Tape (Optional) This part is needed when the cable connector is out of the junction box. 3.3.6 Adjusting Sunshade Cap 3.3.7 Adjusting Lens Angle... - Page 19 Quick Start Guide...