Dahua H Series Quick Start Manual
Ir bullet network camera
Hide thumbs
Also See for H Series:
- Quick start manual (20 pages) ,
- User manual (404 pages) ,
- Quick start manual (19 pages)
Subscribe to Our Youtube Channel
Related Manuals for Dahua H Series
Summary of Contents for Dahua H Series
- Page 1 Model H IR Bullet Network Camera Quick Start Guide ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.4...
-
Page 2: Foreword
Quick Start Guide Foreword General This manual introduces the installation and operations of network camera. Read carefully before using the device, and keep the manual safe for future reference. Safety Instructions The following signal words might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided,... - Page 3 Quick Start Guide About the Manual The manual is for reference only. Slight differences might be found between the manual and the product. We are not liable for losses incurred due to operating of the product in ways that are not in ...
-
Page 4: Important Safeguards And Warnings
Quick Start Guide Important Safeguards and Warnings This section introduces content covering the proper handling of the device, hazard prevention, and prevention of property damage. Read carefully before using the device, comply with the guidelines when using it. Transportation Requirements Transport the device under allowed humidity and temperature conditions. - Page 5 Quick Start Guide Do not place heavy stress on the device, violently vibrate or immerse it in liquid during installation. An emergency disconnect device must be installed during installation and wiring at a readily accessible location for emergency power cut-off. We recommend you use the device with a lightning protection device for stronger protection ...
- Page 6 Quick Start Guide Maintenance Requirements Strictly follow the instructions to disassemble the device. Non-professionals dismantling the device can result in it leaking water or producing poor quality images. For a device that is required to be disassembled before use, make sure the seal ring is flat and in the seal groove when putting the cover back on.
-
Page 7: Table Of Contents
Quick Start Guide Table of Contents Foreword ................................I Important Safeguards and Warnings ......................III 1 Introduction ..............................1 Device Ports ....................................1 Connecting Alarm Input/output ............................2 2 Network Configuration ..........................4 Initializing the Camera ................................4 Changing the Device IP Address ............................5 Logging in to the Webpage.............................. -
Page 8: Introduction
Quick Start Guide Introduction Device Ports Device ports might vary with different models. Waterproof all the cable joints with insulating tape and waterproof tape to avoid water damage and prevent short circuits from occurring. For details, see FAQ manual. Device ports Table 1-1 Device ports information Port Name... -
Page 9: Connecting Alarm Input/Output
Quick Start Guide Port Name Description LAN: Connects to network with network cable; provides power to the device with PoE. / OPT OPT: Connects to OPT devices to connect to the network. Inputs 12 VDC or 24 VAC power. Please be sure to supply power as instructed in the Guide. - Page 10 Quick Start Guide Alarm output Log in to webpage, and then configure alarm input and alarm output in alarm setting. The alarm input on the webpage is corresponding to the alarm input end of the I/O port. There will be high level and low level alarm signal generated by the alarm input device when alarm occurs, set the input mode to "NO"...
-
Page 11: Network Configuration
Quick Start Guide Network Configuration Device initialization and IP address setting can be finished with the ConfigTool or on webpage. For more information, see the Web Operation Manual. Device initialization is available on select models, and it is required at first use or after the ... -
Page 12: Changing The Device Ip Address
Quick Start Guide Select Auto-check for updates as needed, and then click OK to initialize the device. If initialization failed, click to see more information. Click Finish. Changing the Device IP Address You can change the IP address of one or more devices at a time. This section is based on changing ... -
Page 13: Installation
Quick Start Guide Installation Packing List Tools required for installation, such as the electric drill, are not included in the package. The operation manual and information on the tools are on the disk or the QR code. Packing list Dimensions Dimensions (mm [inch]) -
Page 14: Installing The Camera
Quick Start Guide Installing the Camera 3.3.1 Installation Methods Installation methods 3.3.2 (Optional) Installing the SD Card Disconnect the power before installing or removing the SD card. SD card slot is available on select models. Press and hold the reset button for 10 s to reset the camera. Install the SD card 3.3.3 Threading Cable This section uses threading network cable as an example. -
Page 15: Attaching The Camera
Quick Start Guide Thread cable 3.3.4 Attaching the Camera Make sure that the mounting surface is strong enough to hold at least three times the weight of the device and bracket. - Page 16 Quick Start Guide Cable going through the mounting surface...
-
Page 17: Optional) Wrapping Waterproof Tape
Quick Start Guide Cable going through the side cable tray 3.3.5 (Optional) Wrapping Waterproof Tape This part is needed when the cable connector is out of the junction box. -
Page 18: Adjusting Sunshield
Quick Start Guide Wrap waterproof tape 3.3.6 Adjusting Sunshield Adjust sunshield 3.3.7 Adjusting Lens Angle When loosening the bracket, if the screw is blocked by the anti-dropping structure part, turn the screw in the opposite direction for two circles. Adjust lens angle... - Page 19 Quick Start Guide...
Need help?
Do you have a question about the H Series and is the answer not in the manual?
Questions and answers