Advertisement

Quick Links

UM11806
PTN3222CUK-EVB demo board user manual
Rev. 1 — 25 May 2022
Document information
Information
Content
Keywords
PTN3222CUK, eUSB2, eUSB2 repeater, eUSB2 redrive, PTN3222CUK demo
board
Abstract
This user manual describes the PTN3222CUK-EVB demo board in detail,
along with the setup instruction to allow the user to quickly set up the board
for validation.
User manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PTN3222CUK-EVB and is the answer not in the manual?

Questions and answers

Summary of Contents for NXP Semiconductors PTN3222CUK-EVB

  • Page 1 Information Content Keywords PTN3222CUK, eUSB2, eUSB2 repeater, eUSB2 redrive, PTN3222CUK demo board Abstract This user manual describes the PTN3222CUK-EVB demo board in detail, along with the setup instruction to allow the user to quickly set up the board for validation.
  • Page 2 UM11806 NXP Semiconductors PTN3222CUK-EVB demo board user manual Revision history Date Description 20220525 initial version UM11806 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2022. All rights reserved. User manual Rev. 1 — 25 May 2022...
  • Page 3 UM11806 NXP Semiconductors PTN3222CUK-EVB demo board user manual IMPORTANT NOTICE For engineering development or evaluation purposes only NXP provides the product under the following conditions: This evaluation kit is for use of ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY. It is provided as a sample IC pre- soldered to a printed-circuit board to make it easier to access inputs, outputs and supply terminals.
  • Page 4: Introduction

    (12 Mbps) and high speed (480 Mbps). This document is intended to help a user quickly set up, configure and operate the PTN3222CUK-EVB evaluation board in the user's hardware platform. The user manual is applicable to both evaluation boards.
  • Page 5: Kit Featured Components

    4.1 Kit featured components Figure 1. PTN3222CUK-EVB demo board 4.2 Block diagram Figure 2. PTN3222CUK-EVB demo board block diagram 4.2.1 eUSB2 to USB2 connector routing USB2 differential signals can be hardwired via a pair of 0 ohm resistors to type C connector, standard A connector or uB connector. To prevent PCB trace stubs from UM11806 All information provided in this document is subject to legal disclaimers.
  • Page 6: Board Power

    Figure 3. USB2 connector selection 4.3 Board power The PTN3222CUK-EVB can be configured to support eUSB2 host or eUSB2 device mode via port configuration command or via I C. The demo board can be configured via jumpers to be powered from the DC barrel (5 V, 1 A or more), from a uB connector or from the type C connector, the factory default.
  • Page 7: I2C Host Interface And 3V3 Level Shifter

    Figure 5. I C interface 4.5 Schematic, board layout and bill of materials The schematic, board layout and bill of materials for the PTN3222CUK-EVB evaluation board are available at http://www.nxp.com/PTN3222CUK. Board Layout The layout of this board follows the general layout guidelines in AN13462 .
  • Page 8: Legal Information

    NXP Semiconductors. In the event that customer uses the product for design-in and use in In no event shall NXP Semiconductors be liable for any indirect, incidental, automotive applications to automotive specifications and standards, punitive, special or consequential damages (including - without limitation - customer (a) shall use the product without NXP Semiconductors’...
  • Page 9 UM11806 NXP Semiconductors PTN3222CUK-EVB demo board user manual Figures Fig. 1. PTN3222CUK-EVB demo board ....... 5 Fig. 4. PTN3222CUK-EVB demo board power Fig. 2. PTN3222CUK-EVB demo board block selection ............6 diagram ..............5 Fig. 5. I2C interface ............7 Fig. 3.
  • Page 10: Table Of Contents

    UM11806 NXP Semiconductors PTN3222CUK-EVB demo board user manual Contents Introduction ............4 Getting ready ............4 Kit contents ............4 Finding kit resources and information on the NXP web site ..........4 Getting to know the hardware ......4 Kit featured components ........5 Block diagram ............5...

Table of Contents