Table of Contents
Advertisement
Quick Links
CFlux 1
Cyclone Dust Collector
Operating Instructions
Producer:
Laguna Tools Inc
744 Refuge Way, Suite 200
Grand Prairie, Texas 75050
USA
Phone: +1 800-234-1976
Website: www.lagunatools.com
Distributor:
IGM nástroje a stroje s.r.o.
Ke Kopanině 560, 252 67, Tuchoměřice
Czech Republic, EU
Phone: +420 220 950 910
PDF ONLINE
E-mail: sales@igmtools.com
www.igmtools.info
Website: www.igmtools.com
2022-11-02
151-CFlux1 LAGUNA Cyclone Dust Collector Manual EN v1.1.02 A4ob
Advertisement
Table of Contents
Related Manuals for IGM Laguna CFlux 1
Summary of Contents for IGM Laguna CFlux 1
- Page 1 Laguna Tools Inc 744 Refuge Way, Suite 200 Grand Prairie, Texas 75050 Phone: +1 800-234-1976 Website: www.lagunatools.com Distributor: IGM nástroje a stroje s.r.o. Ke Kopanině 560, 252 67, Tuchoměřice Czech Republic, EU Phone: +420 220 950 910 PDF ONLINE E-mail: sales@igmtools.com www.igmtools.info...
- Page 2 www.igmtools.com...
-
Page 3: Table Of Contents
IGM Tools & Machinery strives to always deliver high-quality machinery. • Do not allow to be used as a toy. Close attention is necessary when The warranty is governed by the valid terms and conditions of IGM Tools & used by or near children. -
Page 4: General Safety Rules
• Do not put any object into openings. Do not use with any opening • Provide for adequate space surrounding work area and non-glare, blocked; keep free of dust, lint, hair, and anything that may reduce air flow. overhead lighting. •... -
Page 5: Motor Specifications
associated with each work piece material, and always wear a NIOSH- The installer, such as a qualified electrician, cut (or bend over) and approved respirator to reduce your risk. insulate the grounding conductor from a field wiring supply cable. Dust allergies. Dust from certain woods may cause an allergic reaction in In the event of certain types of malfunctions or breakdowns, grounding people and animals. -
Page 6: Assembly
To assemble your dust cyclone, follow these steps: For your own safety, do not connect the machine to the power source until the machine is completely assembled. Please also make sure that you read and understand the entire instruction manual. ASSEMBLY TIME ESTIMATE 4-5 hours Step 1: Place the empty, top, foam packing insert (which contained the Receiver set... - Page 7 Step 5: Secure the base with (3) lower upright support panels to the unit using (6) 5/16” x 3/4” hex bolts and (6) 5/16” x 1” flat washers. Step 6. Secure the (3) upright support reinforcement plates using (12) Step 10. Secure the foot pedal support to the lower upright support panel 5/16”...
- Page 8 attach the crossbar. Step 18. Apply foam tape to the cone flange before attaching the drum lid. Secure the Octagon drum lid to the cyclone funnel using (6) 5/16” x 3/4” hex bolts, (12) 5/16” x 1” flat washers and (6) 5/16” hex nuts. Make sure to Step 14: Secure the topping with (2) M8 x 30mm hex bolts.
- Page 9 Step 22. Place the Octagon base panel with casters on the bottom of the drum and secure using Secure the Octagon base panel to the bottom of the drum using (22) M5 Sheet metal screws to secure tightly, make sure the head of the sheet metal screw is on the outside of the drum.
- Page 10 the pleated filter and into the filter bag. To improve the effectiveness of the paddles, slowly rotate the handle while simultaneously blowing (from outside – in) into the pleats. This will assist the release of fine dust from the inside of the pleats. NOTE: using the blowing function (hose connected to exhaust port) of a vacuum can also help dislodge dust.
-
Page 11: Troubleshooting Guide
RE-ASSEMBLING THE CANISTER FILTER AFTER CLEANING EMPTYING THE DRUM 1. With the aid of another person, carefully re-insert the canister filter repeating step 1,2,3 and 4 in reverse. Periodically inspect the contents of the drum and empty as needed. To inspect the contents of the drum: EMPTYING OR REPLACING THE FILTER BAG 1. -
Page 12: Power Connections & Wiring Diagrams
8. POWER CONNECTIONS & WIRING DIAGRAMS www.igmtools.com -12-... -
Page 13: Parts Breakdown / Exploded Views
9. PARTS BREAKDOWN / EXPLODED VIEWS FAN, MOTOR & SWITCH www.igmtools.com -13-... - Page 14 CYCLONE, CANISTER & BARREL www.igmtools.com -14-...
- Page 15 PANELS & LOCK BARREL & INSERT www.igmtools.com -15-...
-
Page 16: Parts List
30 x 60mm PDCCF15110-45 RUBBER HANDLE FOR DRUM INSERT PDCCF15110-46 SILICONE Tube PDCCF15110-47 CROSSBAR IGM nástroje a stroje s.r.o., Ke Kopanině 560, Tuchoměřice, 252 67, Czech Republic, E.U. +420 220 950 910, www.igm.cz © 2022 IGM nástroje a stroje s.r.o.
Need help?
Do you have a question about the Laguna CFlux 1 and is the answer not in the manual?
Questions and answers