Table of Contents
Advertisement
Quick Links
PFlux3Tv2 mod.2022
Cyclone Dust Collector
Operating Instructions
Producer:
Laguna Tools Inc
744 Refuge Way, Suite 200
Grand Prairie, Texas 75050
USA
Phone: +1 800-234-1976
Website: www.lagunatools.com
Distributor:
IGM nástroje a stroje s.r.o.
Ke Kopanině 560, 252 67, Tuchoměřice
Czech Republic, EU
Phone: +420 220 950 910
PDF ONLINE
E-mail: sales@igmtools.com
www.igmtools.info
Website: www.igmtools.com
2022-04-04
151-PFlux3Tv2 LAGUNA Cyclone Dust Collector Manual EN v2.0 A4ob
Advertisement
Table of Contents
Related Manuals for IGM Laguna PFlux3Tv2
Summary of Contents for IGM Laguna PFlux3Tv2
- Page 1 Laguna Tools Inc 744 Refuge Way, Suite 200 Grand Prairie, Texas 75050 Phone: +1 800-234-1976 Website: www.lagunatools.com Distributor: IGM nástroje a stroje s.r.o. Ke Kopanině 560, 252 67, Tuchoměřice Czech Republic, EU Phone: +420 220 950 910 PDF ONLINE E-mail: sales@igmtools.com www.igmtools.info...
- Page 2 www.igmtools.com...
-
Page 3: Table Of Contents
IGM Tools & Machinery strives to always deliver high-quality machinery. • Do not allow to be used as a toy. Close attention is necessary when The warranty is governed by the valid terms and conditions of IGM Tools & used by or near children. -
Page 4: General Rules
• Do not use to pick up flammable or combustible liquids, such as • Give your work undivided attention. Looking around, carrying on a gasoline, or use in areas where they may be present. conversation and “horse-play” are careless acts that can result in serious injury. -
Page 5: Motor Specifications
Disconnecting power supply. Turn the switch off, disconnect the disconnect it from power, and immediately replace it with a new one. dust collector from the power supply, and allow the impeller to come to a complete stop before leaving the machine unattended or doing any Electrical Circuit Requirements service, cleaning, maintenance, or adjustments. -
Page 6: Assembly
AC. Autoclean plate AD. Hardware box Report any missing or damaged parts to your dealer or distributor. Prior to tool assembly and use, read this manual thoroughly to familiarize yourself with proper assembly, maintenance and safety procedures. 5.2 General Tool Assembly This step requires two adults. - Page 7 Step 5. Take the intake cylinder, cyclone barrel and cyclone funnel and Step 9: With the help of another person, lift the unit up carefully to the install 3 x 6mm foam tape to rims on each locations shown on the left. right side up with the motor on top and the wheels at the bottom.
- Page 8 Step 18. Locate the two foot pedal bars provided. There is a left side and right side. To identify the correct side, look for the protruding nut, circled in red below. It should be facing upwards when you place the bars on the floor.
- Page 9 bolts have not been tightened for alignment. Failure to do will result in the drum lid not being able to align with the drum. Step 23. Attach the two ends of the Octagon foot pedal to the nut on the foot pedal bar.
- Page 10 Step 32. Attach the handles to the top and bottom end on the front panel with the window display using (4) flat head Philip bolt, (4) 5/16” x 7/8” flat washers and (4) 5/16” hex nuts. Note that the head of the Philip bolt must be inserted from the handle with the hex nut and washer on the inside of the drum.
- Page 11 OPERATION 1. Make sure at least one blast gate is open, if connected to a dust collection system with blast gates. CAUTION Never operate dust collector with all blast gates closed! 2. Confirm the electrical supply is correct and connected to machine. 3.
- Page 12 1. Raise the drum foot peddle bar to lower the drum to the floor. 2. Roll it away from the machine, inspect and empty as needed. ROUTINE INSPECTION It is a good idea to routinely inspect any quality woodworking tool in order to keep it in optimum condition.
- Page 13 7. Troubleshooting guide Machine does not start or a breaker trips. Possible Cause Possible Solution 1. Power supply switched OFF or is faulty. 1. Ensure power supply is ON and has the correct voltage. 2. Wall fuse/circuit breaker is blown/tripped. 2.
- Page 14 8. POWER CONNECTIONS & WIRING DIAGRAMS POWER CONNECTIONS CONTROL PANEL www.igmtools.com -14-...
- Page 15 AUTOCLEAN MOTOR SECONDARY JUNCTION BOX www.igmtools.com -15-...
-
Page 16: Parts Breakdown / Exploded Views
9. Parts breakdown / Exploded Views ¤ s ´ I ¾ ÷ ± ñ ¤ ½ ¥ q 2021. 10. 14 ¥ X ¹ Ï ³ ¹ www.igmtools.com -16-... -
Page 17: Parts List
10. Parts list Ref No Part Number Part Name & Description Ref No Part Number Part Name & Description 16F PDCPF22201-16F FLAT WASHER 5/16”xOD18x2t 1 PDCPF22201-1 MOTOR 2HP 16G PDCPF22201-16G HEX NUT 5/16” 1 PDCPF32201-1 MOTOR 3HP 16H PDCPF22201-16HV2 OCTAGON DRUM BACK PANEL V2.2021 1A PDCPF22201-1A MOTOR GASKET 16K PDCPF22201-16K... - Page 18 PHILIP HD BOLT M4*10mm 51B PDCPF22201-51B FLAT WASHER 3/16”*OD12*1t 51C PDCPF22201-51C HEX NUT M4 IGM nástroje a stroje s.r.o., Ke Kopanině 560, Tuchoměřice, 252 67, Czech Republic, E.U. +420 220 950 910, www.igm.cz © 2022 IGM nástroje a stroje s.r.o.
Need help?
Do you have a question about the Laguna PFlux3Tv2 and is the answer not in the manual?
Questions and answers