MacDon D1X Series Assembly Instructions Manual
  1. Manuals
  2. Brands
  3. MacDon Manuals
  4. Farm Equipment
  5. D1X Series
  6. Assembly instructions manual

MacDon D1X Series Assembly Instructions Manual

Draper header for windrowers
Hide thumbs Also See for D1X Series:
Table of Contents

Advertisement

Quick Links

Download this manual
D1X Series
Draper Header for Windrowers
Unloading and Assembly Instructions (North America)
214047 Revision A
2017 Model Year
Original Instruction
The harvesting specialists.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the D1X Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for MacDon D1X Series

Summary of Contents for MacDon D1X Series

  • Page 1 D1X Series Draper Header for Windrowers Unloading and Assembly Instructions (North America) 214047 Revision A 2017 Model Year Original Instruction The harvesting specialists.
  • Page 2 D1X Series Draper Header for Self-Propelled Windrowers Published: December 2016...
  • Page 3 Introduction This instruction manual describes the unloading, setup, and predelivery requirements for the MacDon D125X and D1XL Series Draper Headers for Self-Propelled Windrowers. To ensure the best performance of this product and the safety of your customers, carefully follow the unload and assembly procedure from the beginning through to completion.

  • Page 5: Table Of Contents

    TABLE OF CONTENTS Introduction ............................i List of Revisions ..........................v Safety ..............................1 Signal Words........................... 1 General Safety ..........................2 Safety Signs ............................ 4 Unloading Header..........................5 Unloading Header from Trailer ......................5 Lowering Header ..........................7 2.2.1 Lowering Single-Reel Header....................7 2.2.2 Lowering Double-Reel Header ....................
  • Page 6 TABLE OF CONTENTS Torque Specifications ........................79 8.1.1 SAE Bolt Torque Specifications ....................79 8.1.2 Metric Bolt Specifications ......................81 8.1.3 Metric Bolt Specifications Bolting into Cast Aluminum ............... 84 8.1.4 Flare-Type Hydraulic Fittings....................84 8.1.5 O-Ring Boss (ORB) Hydraulic Fittings (Adjustable)..............86 8.1.6 O-Ring Boss (ORB) Hydraulic Fittings (Non-Adjustable) ............

  • Page 7: List Of Revisions

    List of Revisions Summary of Change Refer To Added D125 X information. Throughout the publication Put metric measurements before imperial Throughout the publication measurements. Created new illustration (1019022) to show the three bolts securing the shipping support to the left-hand 2.3 Removing Shipping Supports, page 13 endshield.

  • Page 9: Safety

    1 Safety 1.1 Signal Words Three signal words, DANGER, WARNING, and CAUTION, are used to alert you to hazardous situations. The appropriate signal word for each situation has been selected using the following guidelines: DANGER Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. WARNING Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury.

  • Page 10: General Safety

    SAFETY 1.2 General Safety CAUTION The following are general farm safety precautions that should be part of your operating procedure for all types of machinery. Protect yourself. • When assembling, operating, and servicing machinery, wear all protective clothing and personal safety devices that could be necessary for job at hand.
  • Page 11 SAFETY • Wear close-fitting clothing and cover long hair. Never wear dangling items such as scarves or bracelets. • Keep all shields in place. NEVER alter or remove safety equipment. Make sure driveline guards can rotate independently of shaft and can telescope freely. •...

  • Page 12: Safety Signs

    • If original parts on which a safety sign was installed are replaced, be sure repair part also bears current safety sign. • Safety signs are available from your MacDon Dealer. Figure 1.7: Operator’s Manual Decal 214047 Revision A...

  • Page 13: Unloading Header

    2 Unloading Header Perform all procedures in this chapter in the order in which they are listed. 2.1 Unloading Header from Trailer The following procedure assumes that two headers were shipped on the trailer. CAUTION To avoid injury to bystanders from being struck by machinery, do not allow people to stand in unloading area.
  • Page 14 UNLOADING HEADER 3. Approach one of the headers and slide forks (A) underneath the shipping support (B) as far as possible without contacting the shipping support of second header (C). IMPORTANT: Avoid lifting the second header and ensure the forks do not interfere with the shipping frame.

  • Page 15: Lowering Header

    UNLOADING HEADER 2.2 Lowering Header The procedure for lowering the header varies depending on whether the header has a single or double reel. Refer to the following: • 2.2.1 Lowering Single-Reel Header, page 7 • 2.2.2 Lowering Double-Reel Header, page 9 2.2.1 Lowering Single-Reel Header Reposition header in preparation for assembly and setup as follows:...
  • Page 16 UNLOADING HEADER CAUTION Stand clear when lowering, as machine may swing. 4. Back up SLOWLY while lowering forks until header is just above the ground. Refer to the four positions in the illustration. Figure 2.4: Lowering the Header 214047 Revision A...

  • Page 17: Lowering Double-Reel Header

    UNLOADING HEADER 5. Place 150 mm (6 in.) blocks (A) under each end and center of cutterbar, and then lower header onto blocks. 6. Remove chain and move lifting vehicle to rear of header. 7. Attach chain to center-link anchor on frame tube and raise rear of header so that stand can be lowered.
  • Page 18 UNLOADING HEADER 3. Attach a chain to shipping support (A) at center reel arm. IMPORTANT: Do NOT lift header at this location. This procedure is only for laying the machine over into working position. Figure 2.8: Shipping Support 214047 Revision A...
  • Page 19 UNLOADING HEADER CAUTION Stand clear when lowering, as machine may swing. 4. Back up SLOWLY while lowering forks until header is just above the ground. Refer to the four positions in the illustration. Figure 2.9: Lowering the Header 214047 Revision A...
  • Page 20 UNLOADING HEADER 5. Place 150 mm (6 in.) blocks (A) under each end and center of cutterbar, and then lower header onto blocks. 6. Remove chain and move lifting vehicle to rear of header. 7. Attach chain to center-link anchor on frame tube and raise rear of header so that stand can be lowered.

  • Page 21: Removing Shipping Supports

    UNLOADING HEADER 2.3 Removing Shipping Supports NOTE: Unless otherwise specified, discard all shipping materials and hardware. 1. Cut straps and remove draper header supports (A) from shipping support. Set draper header supports aside for reinstallation. Figure 2.12: Straps, Draper Header Supports, and Shipping Supports 2.
  • Page 22 UNLOADING HEADER 4. Remove six bolts (A) securing lower support (B) to header legs and remove support. Figure 2.15: Lower Support 5. Remove the four bolts (A) from the shipping stands at both outboard header legs and remove the shipping stands.
  • Page 23 UNLOADING HEADER 7. At the left-hand side of the header, cut and remove the wire (A) securing the endshield to the panel. Repeat at the opposite side. 8. Loosen the three nuts (B) securing the shipping support to the endsheet. 9.

  • Page 25: Attaching Header To Windrower

    3 Attaching Header to Windrower Perform all the procedures in this chapter in the order in which they are listed. 3.1 Installing the Hydraulic Hose Management Arm The hydraulic hose management arm should be properly installed from shipping position to working position. Lifting equipment is required to complete this task;...
  • Page 26 ATTACHING HEADER TO WINDROWER 4. Remove the two bolts and nuts (A) securing the base of the hose management arm (B) to the frame channel (C). Retain bolts and nuts for use later. 5. Remove the other two bolts and nuts (D) from the shipping plate (E).
  • Page 27 ATTACHING HEADER TO WINDROWER 7. 40–45 Foot Headers: With the sling attached to the lifting device and supporting the hose management arm, cut and remove the wire (A) that secures the hose management arm to channel latch on top of header frame tube.
  • Page 28 ATTACHING HEADER TO WINDROWER 9. Secure the plate support (A) to the frame channel (B) using the four bolts and nuts previously removed. 10. Remove sling from the hose management arm. Figure 3.7: Hose Management Arm Plate Support 11. 25–35 Foot Headers: Remove the two bolts (A) and shipping support (B) from the coupler holder (C).

  • Page 29: Attaching Draper Header Supports

    ATTACHING HEADER TO WINDROWER 3.2 Attaching Draper Header Supports DANGER To avoid bodily injury or death from unexpected startup of the machine, always stop the engine and remove the key from the ignition before leaving the operator’s seat for any reason. 1.

  • Page 30: Connecting Center-Link

    ATTACHING HEADER TO WINDROWER 3.3 Connecting Center-Link DANGER To avoid bodily injury or death from unexpected startup of the machine, always stop the engine and remove the key from the ignition before leaving the operator’s seat for any reason. 1. Stop windrower engine and remove key from ignition. 2.
  • Page 31 ATTACHING HEADER TO WINDROWER 5. In the windrower cab, press scroll knob (A) on HPT to display the QuickMenu system. 6. Rotate scroll knob (A) to highlight the HEADER FLOAT symbol (B) and press scroll knob to select. Figure 3.15: HPT Display 7.
  • Page 32 ATTACHING HEADER TO WINDROWER 9. Drive the windrower slowly forward until the draper header supports (A) enter the header legs (B). Continue driving slowly forward until lift linkages contact the support plates in the header legs and the header nudges forward. 10.
  • Page 33 ATTACHING HEADER TO WINDROWER 12. For hydraulic center-link without self-alignment: a. Press HEADER TILT UP or HEADER TILT DOWN cylinder switches on the GSL to extend or retract center-link cylinder until the hook is aligned with the header attachment pin. b.
  • Page 34 ATTACHING HEADER TO WINDROWER 16. Install pin (B) through the header leg (engaging U-bracket in draper header support) on both sides and secure with a hairpin (A). 17. Raise header stand (D) to storage position by pulling spring pin (C) and lifting stand into uppermost position. Release spring pin.

  • Page 35: Connecting Hydraulics

    ATTACHING HEADER TO WINDROWER 3.4 Connecting Hydraulics IMPORTANT: To prevent contamination of the hydraulic system, use a clean rag to remove dirt and moisture from all (fixed and movable) hydraulic couplers. 1. Move arm (B) toward left cab-forward side of windrower.
  • Page 36 ATTACHING HEADER TO WINDROWER 7. Retrieve draper drive and reel control multicoupler (A) from hose management arm. 8. Push knob (B) on hydraulic receptacle and pull handle (C) fully away from windrower. 9. Open cover (D) and position coupler onto receptacle. Align pins in coupler with slots in handle (C) and push handle toward windrower so that coupler is locked onto receptacle and knob (B) snaps out.
  • Page 37 ATTACHING HEADER TO WINDROWER 17. Ensure hydraulic hose routing is as straight as possible and avoids potential rub/wear points. Figure 3.32: Hydraulic Multicouplers and Hose Routing 214047 Revision A...

  • Page 39: Assembling The Header

    4 Assembling the Header Perform all the procedures in this chapter in the order in which they are listed. 4.1 Attaching Reel Lift Cylinders CAUTION Bolts (A) (with tags) on reel arms keep the reel from sliding forward. Ensure fore-aft cylinders are attached before removing bolts.
  • Page 40 ASSEMBLING THE HEADER 1. Position sling (A) around the reel tube (B) close to the outboard end of reel and attach sling to a forklift (or equivalent). 2. Remove shipping wire/banding from the reel lift cylinder. Figure 4.3: Reel Tube 3.
  • Page 41 ASSEMBLING THE HEADER 5. Lift reel and remove pins from the endsheet and the reel arm. 6. Align the reel lift cylinder mounting holes until they line up with the lug on endsheet and the hole in the reel arm. 7.
  • Page 42 ASSEMBLING THE HEADER NOTE: Step 9, page 34 to Step 16, page 34 apply ONLY to double-reel headers; for single-reel headers, go to Step 17, page 9. Double reel only: Position sling (A) around the reel tube near the reel center support arm. 10.
  • Page 43 ASSEMBLING THE HEADER 19. Lift reel and remove pins from the endsheet (B) and the reel arm (A). 20. Align the reel lift cylinder mounting holes until they line up with the lug on endsheet and the hole in the reel arm. 21.
  • Page 44 ASSEMBLING THE HEADER 23. Double reel only: Remove the remaining bolt (A), disengage center reel arm shipping support (B) from cutterbar, and remove shipping support. Figure 4.13: Center Reel Arm Shipping Support 24. Remove bolts (A) from reel arm support at endsheet and remove support.
  • Page 45 ASSEMBLING THE HEADER 25. Remove brace bolts and tags (A) locking the reel fore-aft position at outer reel arms. NOTE: Do NOT use hydraulic pressure to move fore-aft cylinder to aid in removing brace bolts. Cylinder damage may occur. Figure 4.15: Right Reel Arm Top Image - Single Reel Bottom Image - Double Reel Figure 4.16: Left Reel Arm...
  • Page 46 ASSEMBLING THE HEADER 26. Double reel only: Remove the remaining three bolts (A) locking the reel fore-aft position at the center reel arm and remove shipping channel (B). Figure 4.17: Center Reel Arm Shipping Channel (Double-Reel Header Only) 214047 Revision A...

  • Page 47: Installing Disc Segments Of Outboard Reel Endshields

    ASSEMBLING THE HEADER 4.2 Installing Disc Segments of Outboard Reel Endshields To meet the trucking load regulations for the maximum load width and height, two disc segments of the reel endshields (A) may have been removed from the right-hand reel (tail end) and left-hand reel (cam end). Check if reel endshields are completely installed.

  • Page 48: Attaching Cam Arms

    ASSEMBLING THE HEADER 4.3 Attaching Cam Arms To attach the reel cam arms, follow these steps: 1. Rotate the reel manually until the tine bars with disconnected cam links are accessible. 2. Remove shipping wire (A) (if not already removed). Figure 4.21: Disconnected Cam Links and Shipping Wire 3.

  • Page 49: Installing Crop Dividers

    ASSEMBLING THE HEADER 4.4 Installing Crop Dividers One crop and two rod dividers are stored on the right inboard side of the endsheet; the other crop divider is stored on the left inboard side of the endsheet. 1. Remove the shipping wire (A) and loosen the bolt (B) on the lock tab securing the divider rods (C) to the bracket storage.
  • Page 50 ASSEMBLING THE HEADER 7. Lift forward end of divider up to endsheet and install washer (A) and bolt (B). Figure 4.27: Installation Hardware 8. Position divider rod (B) on tip of crop divider as shown and tighten bolt (A). Figure 4.28: Divider Rod on Crop Divider 9.

  • Page 51: Positioning Transport Lights

    ASSEMBLING THE HEADER 4.5 Positioning Transport Lights Transport lights are located on each of the outboard reel arms. 1. Position lights (A) perpendicular to header. Figure 4.30: Transport Light Perpendicular to Header 214047 Revision A...

  • Page 52: Installing Options

    ASSEMBLING THE HEADER 4.6 Installing Options Retrieve the kits supplied as options with the header and install them according to the instructions supplied with each kit. 214047 Revision A...

  • Page 53: Adding Ballast

    ASSEMBLING THE HEADER 4.7 Adding Ballast M1-Series windrowers use counterweight kits to add ballast. The counterweights are used to improve a windrower’s balance while operating with a header. Each kit comes with eight counterweights totaling 163 kg (360 lb.) and required hardware.
  • Page 54 ASSEMBLING THE HEADER Initial Rear Additional Rear Header Type Description Header Configuration Ballast Kit Ballast Kits 45-ft. double reel, D145XL double knife, Base untimed 45-ft. double reel, D145XL double knife, Transport untimed 45-ft. double reel, Transport D145XL double knife, Upper cross auger untimed Vertical knives When the recommended fluid ballast has been added, proceed to...

  • Page 55: Performing Predelivery Checks

    5 Performing Predelivery Checks This machine has been set at the factory and should not require further adjustments; however, the following checks will ensure your machine provides maximum performance. If adjustments are necessary, follow the procedures in this chapter. WARNING To avoid bodily injury or death from unexpected startup of machine, always stop engine and remove key before making adjustments to machine.

  • Page 56: Checking Wheel Bolt Torque

    PERFORMING PREDELIVERY CHECKS 5.2 Checking Wheel Bolt Torque Perform the following procedure to ensure that transport and stabilizer wheel bolts are correctly torqued: 1. Check wheel bolt torque is 110–120 N·m (80–90 lbf·ft) and adjust as necessary. Refer to bolt tightening sequence illustration at right.

  • Page 57: Checking Knife Drive Box

    PERFORMING PREDELIVERY CHECKS 5.3 Checking Knife Drive Box To access the knife drive box(es), endshield(s) must be fully opened. Single-knife headers have one knife-drive box and double-knife headers have two knife-drive boxes. WARNING To avoid bodily injury or death from unexpected startup of machine, always stop engine and remove key before making adjustments to machine.
  • Page 58 PERFORMING PREDELIVERY CHECKS IMPORTANT: The knife drive box breather is shipped in position (A) (forward) to prevent oil loss during transport. The breather plug MUST be repositioned to location (B) to prevent oil loss during normal operation. Failure to do so can result in damage to the knife drive box.

  • Page 59: Checking And Adjusting Knife Drive Belt Tension

    PERFORMING PREDELIVERY CHECKS 5.4 Checking and Adjusting Knife Drive Belt Tension Proceed to the section that applies to the header’s knife drive configuration: • 5.4.1 Tensioning Non-Timed Knife Drive Belts, page 51 • 5.4.2 Tensioning Timed Knife Drive Belts, page 52 •...

  • Page 60: Tensioning Timed Knife Drive Belts

    PERFORMING PREDELIVERY CHECKS 5.4.2 Tensioning Timed Knife Drive Belts The procedure for tensioning timed knife drive belts is the same for both sides of the header. The illustrations shown are for the left side—the right side is opposite. IMPORTANT: To prolong belt and drive life, do NOT over tighten belt. IMPORTANT: Do NOT use the adjuster bolt at the drive pulley to adjust timing belt tension.
  • Page 61 PERFORMING PREDELIVERY CHECKS 4. Tighten nuts (A) on idler pulleys (B) to 217 N·m (160 lbf·ft). Figure 5.9: LH Knife Drive 5. Tighten jam nut (A) to prevent loosening of the adjuster bolt (B). Figure 5.10: LH Knife Drive 6. Ensure there is a clearance of 2.5–3.5 mm (1/8 in.) between the lower belt (A) and lower guide (B).

  • Page 62: Tensioning Timed Knife Drive V-Belts

    PERFORMING PREDELIVERY CHECKS 5.4.3 Tensioning Timed Knife Drive V-Belts 1. Loosen the two bolts (A). 2. Turn drawbolt clockwise tighten counterclockwise to loosen belts (C) tension. NOTE: Tension is checked at mid-span of the belts. The belts should deflect 4 mm (5/32 in.) with 52–77 N (12–17 lbf) of force applied to each belt.

  • Page 63: Centering The Reel

    PERFORMING PREDELIVERY CHECKS 5.5 Centering the Reel Refer to the topic for header type: • 5.5.1 Centering Double Reels, page 55 • 5.5.2 Centering Single Reels, page 55 5.5.1 Centering Double Reels WARNING To avoid bodily injury or death from unexpected startup of machine, always stop engine and remove key before making adjustments to machine.
  • Page 64 PERFORMING PREDELIVERY CHECKS 1. Measure the clearance at locations (A) between the reel and endsheets. The clearances should be the same if the reel is centered. If not centered, continue on the next step. Figure 5.15: Single Reel Measurement Locations 2.

  • Page 65: Adjusting Draper Tension

    PERFORMING PREDELIVERY CHECKS 5.6 Adjusting Draper Tension WARNING To avoid bodily injury or death from unexpected start-up or fall of raised machine, always stop engine, remove key, and engage safety props before going under machine for any reason. 1. Ensure the white indicator bar (A) is at the halfway point in the window.
  • Page 66 PERFORMING PREDELIVERY CHECKS IMPORTANT: Do NOT adjust nut (C). This nut is used for draper alignment only. 7. To loosen the adjuster bolt (A), turn it counterclockwise. The white indicator bar (B) will move outboard in the direction of arrow (D) to indicate that the draper is loosening.

  • Page 67: Checking And Adjusting Draper Seal

    PERFORMING PREDELIVERY CHECKS 5.7 Checking and Adjusting Draper Seal Maintain the deck height such that the draper runs just below the cutterbar. IMPORTANT: New factory installed drapers are pressure and heat checked at the factory. The gap between the draper (A) and cutterbar (B) is set to 1–3 mm (1/32–1/8 in.).
  • Page 68 PERFORMING PREDELIVERY CHECKS 4. Loosen two lock nuts (A) only one-half-turn on deck support (B). 5. Tap deck (C) to lower deck relative to supports and achieve the recommended setting. Tap support (B) using a punch to raise deck relative to supports. 6.

  • Page 69: Checking And Adjusting Skid Shoe Settings

    PERFORMING PREDELIVERY CHECKS 5.8 Checking and Adjusting Skid Shoe Settings Check skid shoes and adjust, if necessary. WARNING To avoid bodily injury or death from unexpected start-up or fall of raised machine, always stop engine, remove key, and engage safety props before going under machine for any reason. DANGER Engage header safety props and reel props before working under header or reel.

  • Page 70: Levelling The Header

    PERFORMING PREDELIVERY CHECKS 5.9 Levelling the Header The windrower linkages are factory-set to provide the proper level for the header and should not normally require adjustment. 1. If the header is not level, check the pressure of the windrower’s tires to ensure they are properly inflated (refer to your windrower operator’s manual).

  • Page 71: Measuring And Adjusting Reel Clearance To Cutterbar

    PERFORMING PREDELIVERY CHECKS 5.10 Measuring and Adjusting Reel Clearance to Cutterbar The minimum clearance between the reel fingers and the cutterbar ensures that the reel fingers do not contact the cutterbar during operation. The clearance is set at the factory, but some adjustment may be necessary before operation.
  • Page 72 PERFORMING PREDELIVERY CHECKS 5. Measure the clearance (X) at all possible points of contact between points (B) and (C) at the ends of each reel (A). NOTE: The reel is factory-set to provide more clearance at the center of the reel than at the ends (frown) to compensate for reel flexing.

  • Page 73: Adjusting Reel Clearance

    PERFORMING PREDELIVERY CHECKS 5.10.2 Adjusting Reel Clearance DANGER To avoid bodily injury or death from unexpected start-up or fall of raised machine, always stop engine, remove key, and engage safety props before going under header for any reason. IMPORTANT: After setting the recommended reel clearance to cutterbar, while reel is still fully lowered, move reel back to ensure steel end fingers do NOT contact deflector shields.

  • Page 74: Checking And Adjusting Endshields

    PERFORMING PREDELIVERY CHECKS 5.11 Checking and Adjusting Endshields Endshields are subject to expansion or contraction caused by large temperature variations. The position of the top pin and lower latch can be adjusted to compensate for dimensional changes. 1. Check gap (X) between front end of shields and header frame and compare to the values in Table 5.3 Endshield Gap at Various Temperatures, page...
  • Page 75 PERFORMING PREDELIVERY CHECKS 4. Pull endshield at handle depression (A). Endshield is retained by a hinge tab (B) and will open in direction (C). Figure 5.36: Left Endshield 5. Pull the endshield free of hinge tab (A) if additional clearance is required, and swing shield towards the rear of the header.
  • Page 76 PERFORMING PREDELIVERY CHECKS 8. Loosen the three bolts (A) on latch assembly (B). 9. Adjust latch assembly (B) to achieve the desired gap between the front end of shield and header frame in accordance with Table 5.3 Endshield Gap at Various Temperatures, page 10.

  • Page 77: Lubricating The Header

    PERFORMING PREDELIVERY CHECKS 5.12 Lubricating the Header Table 5.4 Recommended Lubricant Specification Description High temperature, extreme pressure (EP2) performance As required unless with 1% max molybdenum disulphide (NLGI Grade 2) otherwise specified lithium base SAE multipurpose High temperature, extreme pressure (EP) performance with 10% max molybdenum disulphide (NLGI Grade 2) Driveline slip-joints lithium base...
  • Page 78 PERFORMING PREDELIVERY CHECKS 1. Wipe grease fitting with a clean cloth before greasing to avoid injecting dirt and grit. IMPORTANT: Use clean, high-temperature, extreme-pressure grease only. 2. Inject grease through fitting with grease gun until grease overflows fitting (except where noted). 3.

  • Page 79: Lubrication Points

    PERFORMING PREDELIVERY CHECKS 5.12.2 Lubrication Points Knifehead IMPORTANT: Overgreasing can cause the knife to bend and make contact with the guards closest to the knifehead. Check for signs of excessive heating on first few guards after greasing. If required, relieve some pressure by removing the grease fitting.
  • Page 80 PERFORMING PREDELIVERY CHECKS IMPORTANT: The reel U-joint (C) has an extended lubrication cross and bearing kit. Stop greasing when greasing becomes difficult or if U-joint stops taking grease. OVERGREASING WILL DAMAGE U-JOINT. Six to eight pumps is sufficient at first grease (factory). As U-joint wears and requires more than six pumps, grease the joint more often. Figure 5.45: Reel Shaft Bearings A - Reel Shaft Right-Hand Bearing (One Place) B - Reel Center Bearing (One Place)

  • Page 81: Checking Manuals

    PERFORMING PREDELIVERY CHECKS 5.13 Checking Manuals Check manual case contents. The manual case is located inside the left-hand endshield. 1. Open the left-hand endshield and remove the cable tie on the manual case. Figure 5.46: Manual Case 2. Confirm that the case contains the following manuals: •...

  • Page 83: Running Up The Header

    6 Running up the Header To run up the header, follow these steps: CAUTION Clear the area of other persons, pets etc. Keep children away from machinery. Walk around the machine to be sure no one is under, on, or close to it. CAUTION Before investigating an unusual sound or attempting to correct a problem, shut off engine, engage parking brake, and remove key.

  • Page 85: Performing Post Run-Up Adjustments

    7 Performing Post Run-Up Adjustments Perform post run-up check as listed on the Predelivery Checklist (yellow sheet attached to this instruction Predelivery Checklist, page 97) to ensure machine is field-ready. WARNING To avoid bodily injury or death from unexpected startup of machine, always stop engine and remove key before making adjustments to machine.
  • Page 86 PERFORMING POST RUN-UP ADJUSTMENTS 5. Adjust guard tips downward by positioning tool as shown and pushing down. Figure 7.3: Guard Tips – Downward Adjustment 214047 Revision A...

  • Page 87: Reference

    8 Reference 8.1 Torque Specifications The following tables provide correct torque values for various bolts, cap screws, and hydraulic fittings. • Tighten all bolts to torque values specified in charts (unless otherwise noted throughout this manual). • Replace hardware with same strength and grade of bolt. •...
  • Page 88 REFERENCE Table 8.2 SAE Grade 5 Bolt and Grade F Distorted Thread Nut Torque (lbf·ft) Torque (Nm) Nominal (*lbf·in) Size (A) Min. Max. Min. Max. 1/4-20 5/16-18 16.7 18.5 *149 *164 3/8-16 7/16-14 1/2-13 9/16-12 Figure 8.2: Bolt Grades 5/8-11 A - Nominal Size B - SAE-8 C - SAE-5...

  • Page 89: Metric Bolt Specifications

    REFERENCE Table 8.4 SAE Grade 8 Bolt and Grade 8 Free Spinning Nut Torque (lbf·ft) Torque (Nm) Nominal (*lbf·in) Size (A) Min. Max. Min. Max. 1/4-20 16.8 18.6 *150 *165 5/16-18 3/8-16 7/16-14 1/2-13 9/16-12 Figure 8.4: Bolt Grades 5/8-11 A - Nominal Size B - SAE-8 C - SAE-5...
  • Page 90 REFERENCE Table 8.6 Metric Class 8.8 Bolts and Class 9 Distorted Thread Nut Torque (lbf·ft) Torque (Nm) Nominal (*lbf·in) Size (A) Min. Max. Min. Max. 3-0.5 3.5-0.6 4-0.7 5-0.8 6-1.0 8-1.25 18.8 20.8 *167 *185 Figure 8.6: Bolt Grades 10-1.5 12-1.75 14-2.0 16-2.0...
  • Page 91 REFERENCE Table 8.8 Metric Class 10.9 Bolts and Class 10 Distorted Thread Nut Torque (lbf·ft) Torque (Nm) Nominal (*lbf·in) Size (A) Min. Max. Min. Max. 3-0.5 3.5-0.6 4-0.7 5-0.8 6-1.0 10.7 11.8 *105 8-1.25 Figure 8.8: Bolt Grades 10-1.5 12-1.75 14-2.0 16-2.0 20-2.5...

  • Page 92: Metric Bolt Specifications Bolting Into Cast Aluminum

    REFERENCE 8.1.3 Metric Bolt Specifications Bolting into Cast Aluminum Table 8.9 Metric Bolt Bolting into Cast Aluminum Bolt Torque Nominal 10.9 Size (A) (Cast Aluminum) (Cast Aluminum) lbf·ft lbf·ft – – – – – – – Figure 8.9: Bolt Grades –...
  • Page 93 REFERENCE Table 8.10 Flare-Type Hydraulic Tube Fittings Torque Value Flats from Finger Tight (FFFT) SAE Dash Size Thread Size (in.) Swivel Nut or lbf·ft Tube Hose — — 5/16–24 4–5 3–4 7–8 5–6 — — 3/8–24 7/16–20 18–19 13–14 2-1/2 1/2–20 19–21 14–15...

  • Page 94: O-Ring Boss (Orb) Hydraulic Fittings (Adjustable)

    REFERENCE 8.1.5 O-Ring Boss (ORB) Hydraulic Fittings (Adjustable) 1. Inspect O-ring (A) and seat (B) for dirt or obvious defects. 2. Back off lock nut (C) as far as possible. Ensure that washer (D) is loose and is pushed toward lock nut (C) as far as possible.
  • Page 95 REFERENCE Table 8.11 O-Ring Boss (ORB) Hydraulic Fittings (Adjustable) Torque Value SAE Dash Size Thread Size (in.) lbf·ft (*lbf·in) 5/16–24 6–7 *53–62 3/8–24 12–13 *106–115 7/16–20 19–21 14–15 1/2–20 21–33 15–24 9/16–18 26–29 19–21 3/4–16 46–50 34–37 7/8–14 75–82 55–60 1-1/16–12 120–132 88–97...

  • Page 96: O-Ring Boss (Orb) Hydraulic Fittings (Non-Adjustable)

    REFERENCE 8.1.6 O-Ring Boss (ORB) Hydraulic Fittings (Non-Adjustable) 1. Inspect O-ring (A) and seat (B) for dirt or obvious defects. 2. Check that O-ring (A) is NOT on threads and adjust if necessary. 3. Apply hydraulic system oil to O-ring. 4.

  • Page 97: O-Ring Face Seal (Orfs) Hydraulic Fittings

    REFERENCE 8.1.7 O-Ring Face Seal (ORFS) Hydraulic Fittings 1. Check components to ensure that sealing surfaces and fitting threads are free of burrs, nicks, scratches, or any foreign material. Figure 8.14: Hydraulic Fitting 2. Apply hydraulic system oil to O-ring (B). 3.
  • Page 98 REFERENCE Table 8.13 O-Ring Face Seal (ORFS) Hydraulic Fittings Torque Value SAE Dash Size Thread Size (in.) Tube O.D. (in.) lbf·ft – – Note 3/16 9/16 25–28 18–21 Note 5/16 – – 11/16 40–44 29–32 13/16 55–61 41–45 80–88 59–65 1-3/16 115–127 85–94...

  • Page 99: Tapered Pipe Thread Fittings

    REFERENCE 8.1.8 Tapered Pipe Thread Fittings Assemble pipe fittings as follows: 1. Check components to ensure that fitting and port threads are free of burrs, nicks and scratches, or any form of contamination. 2. Apply pipe thread sealant (paste type) to external pipe threads. 3.

  • Page 100: Lifting Equipment Requirements

    REFERENCE 8.2 Lifting Equipment Requirements The following topic describes the minimum equipment requirements for lifting headers. CAUTION To avoid injury to bystanders from being struck by machinery, do not allow people to stand in unloading area. CAUTION Equipment used for loading and unloading must meet or exceed the minimum specified requirements. Using inadequate equipment may result in vehicle tipping, machine damage, or chain breakage.

  • Page 101: Conversion Chart

    REFERENCE 8.3 Conversion Chart Table 8.17 Conversion Chart SI Units (Metric) Inch-Pound Units Quantity Factor Unit Name Abbreviation Unit Name Abbreviation Area hectares x 2.4710 = acres acres US gallons Flow liters per minute L/min x 0.2642 = per minute Force Newtons x 0.2248 =...

  • Page 102: Definitions

    A hydraulic cylinder link between header and machine used to change header angle CGVW Combined vehicle gross weight D1X Series header MacDon D125X rigid draper headers for windrowers MacDon D130XL, D135XL, D140XL, and D145XL rigid draper headers for D1XL Series header windrowers. Double knife Double-knife drive...
  • Page 103 REFERENCE Term Definition An internally threaded fastener that is designed to be paired with a bolt N-DETENT The slot opposite the NEUTRAL position on operator’s console North American header Header configuration typical in North America National Pipe Thread: A style of fitting used for low pressure port openings Threads on NPT fittings are uniquely tapered for an interference fit O-ring boss: A style of fitting commonly used in port opening on manifolds, pumps, and motors...

  • Page 105: Predelivery Checklist

    Predelivery Checklist Perform these checks prior to delivery to your Customer. Adjustments are normally not required as the machine is factory-assembled and adjusted. If adjustments are required, refer to the appropriate page number in this manual. The completed Checklist should be retained by either the Operator or the Dealer. CAUTION Carefully follow the instructions given.
  • Page 106 PREDELIVERY CHECKLIST Item  Reference — Check if reel lift cylinders extend fully. Check if reel moves fully fore and aft. — Post run-up check. Stop engine. 7 Performing Post Run-Up Adjustments, page 77 5.4 Checking and Adjusting Knife Drive Belt Check belt drives for heated bearings.
  • Page 108 10708 N. Pomona Avenue Kansas City, Missouri United States 64153-1924 t. (816) 891-7313 f. (816) 891-7323 MacDon Australia Pty. Ltd. A.C.N. 079 393 721 P.O. Box 103 Somerton, Victoria, Australia 3062 54 National Boulevard, Campbellfield, Victoria, Australia 3061 t. 61 3 8301-1911 f.

This manual is also suitable for:

D125xD130xlD135xlD140xl

Table of Contents