Display Protection - NEC MultiSync X555UNV User Manual

VIDEO OUT SETTING Enables the signal output from DPORT. See also page 28 "DisplayPort" in TERMINAL SETTING.
NOTE: When VGA or Y/Pb/Pr is selected as the main picture, nothing will be output from DPORT.
When this function is ON, DPORT cannot be selected as the sub picture. When this function is
ON, INPUT CHANGE is limited to be NORMAL or QUICK. When this function is ON and DPORT
is selected as the main picture, PIP CHANGE button of remote control (see page 11) is disabled.
*1: *1: Main picture in PIP (Picture in Picture) mode.
*2: When you use HDMI OUT connector in SB3-DB1, multicple monitors connection is available. *2:
POWER INDICATOR Turns ON or OFF the LED located at the back of the monitor.
If "OFF" is selected, LED will not light when the LCD monitor is in active mode.
SETTING COPY In a daisy chain scenario, select the OSD menu categories that you want to copy over to the
other monitor.
NOTE: When you use this function, monitors should be daisy chained by LAN. This function
resets to default when power is off. This function has a limit depending on the cable you use.
COPY START Select "YES" and press the SET button to start copying.
ALL INPUT All input terminals settings are copied when you select this item. Default is off.
RESET Resets "MULTI DISPLAY" options back to factory settings except for POWER ON DELAY and
VIDEO OUT SETTING.

DISPLAY PROTECTION

POWER SAVE Sets how long the monitor waits to go into power save mode after the signal is lost.
NOTE: When connecting DVI, the display card might not stop sending the digital data even
though the image might have disappeared. If this occurs the monitor will not switch into power
management mode. POWER SAVE is disabled when AUTO OFF or CUSTOM is selected in
HUMAN SENSING.
AUTO POWER SAVE The monitor automatically goes into OFF at the preset time period after signal is lost.
The monitor will return to normal mode when signal is restarted.
AUTO STANDBY The monitor automatically goes into OFF at the preset time period after signal is lost.
Press the power button to return to normal mode.
DISABLE The monitor will not goes into OFF after signal is lost.
HEAT STATUS Displays status of the FAN, BACKLIGHT and TEMPERATURE.
FAN CONTROL Cooling fan reduces the temperature of the display to protect from overheating.
If "AUTO" is selected, you can adjust the start temperature of the cooling fan and fan speed.
SCREEN SAVER Use the SCREEN SAVER function to reduce the risk of Image Persistence.
GAMMA The display gamma is changed and fi xed when "ON" is selected.
BACKLIGHT The brightness of backlight is decreased when "ON" is selected.
NOTE: Do not select this function when ROOM LIGHT SENSING is MODE1 or MODE2.
MOTION The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT) at
user determined intervals. You can set interval time and zooming ratio.
This function is disabled when PIP, STILL, TEXT TICKER or TILE MATRIX are enabled.
SIDE BORDER COLOR Adjusts the color of the side borders when a 4:3 image is displayed.
Press + button, the bar will become lighter.
Press - button, the bar will become darker.
CHANGE PASSWORD Allows the security password to be changed.
The factory preset password is 0000.
SECURITY Locks the security password.
START-UP LOCK: Security password is required when the monitor power is on.
CONTROL LOCK: Security password is required when the remote control button or control button
on the monitor is pressed.
BOTH LOCK: Security password is required when the monitor power is on, or the remote control
button or control button on the monitor is pressed.
RESET Resets the following settings within the DISPLAY PROTECTION menu back to factory setting:
POWER SAVE, FAN CONTROL, SCREEN SAVER, SIDE BORDER COLOR.
Input signal
DPORT DPORT DVI DVI HDMI HDMI VGA VGA Y/Pb/Pr
name* 1
Connector Connector DisplayPort DVI-D DisplayPort DVI-D HDMI HDMI D-Sub D-Sub
DP OUT DP OUT Yes Yes Yes Yes Yes Yes —
Main picture in PIP (Picture in Picture) mode.
When you use HDMI OUT connector in SB3-DB1, multicple monitors connection is available.
When you use DPOUT for HDCP authentication signal, Input signal name should be DPORT. When you use DPOUT for HDCP authentication signal, Input signal name should be DPORT.
Multiple monitors that are daisy-chained have a limit to the connectable monitors. Multiple monitors that are daisy-chained have a limit to the connectable monitors.
Y/Pb/Pr OPTION OPTION VIDEO VIDEO S-VIDEO S-VIDEO SCART SCART
SLOT2 SLOT2
— Yes Yes — — —
(SB3-AB1) (SB3-AB1)
English-26
Y/Pb/Pr2 Y/Pb/Pr2 RGB/HV HDMI2 RGB/HV HDMI2 HDMI3 HDMI3
SLOT3 SLOT3
— — Yes Yes
2 2
Yes Yes —* —*
(SB3-AB2) (SB3-AB2)
ON
ON
NO
-
AUTO
STANDBY
-
-
-
-
AUTO, HIGH
OFF
OFF
OFF
15
-
OFF
-