External Control; Advanced Option1 - NEC MultiSync X555UNV User Manual

EXTERNAL CONTROL

IP ADDRESS SETTING NOTE: When changing the LAN SETTING, you need to wait several seconds until the LAN
SETTING is applied.
IP SETTING Enabling this option automatically assigns an IP address to the monitor from your DHCP server.
Disabling this option allows you to register the IP address or subnet mask number obtained from
your network administrator.
NOTE: Consult your network administrator for the IP address when "AUTO" is selected for
[IP SETTING].
IP ADDRESS Set your IP address of the network connected to the monitor when "MANUAL" is selected for
[IP SETTING].
SUBNET MASK Set your subnet mask number of the network connected to the monitor when "MANUAL" is
selected for [IP SETTING].
DEFAULT GATEWAY Set your default gateway of the network connected to the monitor when "MANUAL" is selected
for [IP SETTING].
NOTE: Set as [0.0.0.0] to delete the setting.
DNS Set for IP ADDRESS SETTING of DNS server.
AUTO: Automatically assign an IP address of DNS server connected to the monitor.
MANUAL: Set your IP address of DNS server connected to the monitor.
DNS PRIMARY Set your primary DNS settings of the network connected to the monitor.
NOTE: Set as [0.0.0.0] to delete the setting.
DNS SECONDARY Set your secondary DNS settings of the network connected to the monitor.
NOTE: Set as [0.0.0.0] to delete the setting.
MAC ADDRESS Displays the MAC ADDRESS.
LAN POWER Selects LAN operation mode. When "ON" selected, allows to supply power to LAN during power
save mode or standby mode.
NOTE: For enabling "AUTO ID" or "AUTO TILE MATRIX SETUP", this function should be ON.
DDC/CI ENABLE/DISABLE: Turns ON or OFF the two way communication and control of the monitor.
PING Confi rm the response by communicating to the preset IP address.
IP ADDRESS RESET Resets IP ADDRESS SETTING back to factory settings.
RESET Resets the following setting within the EXTERNAL CONTROL menu back to factory settings:
DDC/CI.

ADVANCED OPTION1

INPUT DETECT Selects the method of input detection the monitor uses when more than two input devices are
connected.
NOTE: When SUPER is selected in INPUT CHANGE, this function cannot be changed.
NONE The Monitor will not search the other video input ports.
FIRST DETECT* 2 When the current video input signal is not present, then the monitor searches for a video signal
from the other video input port. If the video signal is present in the other port, then the monitor
switches the video source input port to the new found video source automatically.
The monitor will not look for other video signals while the current video source is present.
LAST DETECT* 2 When the monitor is displaying a signal from the current source and a new secondary source
is supplied to the monitor, the monitor will automatically switch to the new video source. When
current video input signal is not present, the monitor searches for a video signal from the other
video input port. If the video signal is present in the other port, then the monitor switches the
video source input port to the new found video source automatically.
VIDEO DETECT VIDEO inputs such as HDMI, HDMI2*
S-VIDEO*
signals is present the monitor will change and keep to the VIDEO input.
CUSTOM DETECT Set the priority of input signals.
When CUSTOM DETECT is selected, monitor searches listed inputs only.
NOTE: Priority of option input signal is only available in PRIORITY3 except for slot 2 type
PC option.
*1: This function depends on which option board you use.
*2: Only for DVI, DPORT, VGA, RGB/HV*
1
1 will have priority over DVI, VGA, DPORT, RGB/HV*
1 , HDMI, HDMI2* 1 , HDMI3* 1 input.
English-27
1 1
, HDMI3* , Y/Pb/Pr, Y/Pb/Pr2* , SCART*
1 . When one of the VIDEO input
AUTO
192.168.0.10
255.255.255.0
0.0.0.0
AUTO
0.0.0.0
0.0.0.0
-
OFF
ENABLE
192.168.0.10
NO
NO
-
NONE
1 1
, VIDEO* or