Table of Contents
Advertisement
MULTI DISPLAY
TILE MATRIX*
1
(Except for MP)
H MONITORS
V MONITORS
POSITION
TILE COMP
ENABLE
TILE MATRIX MEM
COMMON
INPUT
ID CONTROL
RESET
DISPLAY PROTECTION
POWER SAVE
AUTO POWER SAVE
TIME SETTING
QUICK TURN ON
STANDBY USB
POWER
POWER SAVE MESSAGE When the monitor goes into power save mode, a message is displayed when ON is selected.
HEAT STATUS
SCREEN SAVER
BACKLIGHT
MOTION
SIDE BORDER COLOR
POWER ON DELAY
DELAY TIME
LINK TO ID
ALERT MAIL
RESET
*1: Except for MP.
Allows one image to be expanded and displayed over multiple screens (up to 100) through a distribution
amplifier.
NOTE: Low resolution is not suitable for tiling to a large number of monitors. You can operate without a
distribution amplifier at a lower number of screens.
This function is released when selecting SCREEN SAVER except for NONE.
Zoom will not work when Tile Matrix is activated.
When "ZOOM" is selected in ASPECT while executing TILE MATRIX, the setting will be applied after completing
the TILE MATRIX.
When TILE MATRIX is active the following functions are not available: CLOSED CAPTION, STILL,
POINT ZOOM. Please refer to the POINT ZOOM function for more detail (see page 49).
If Media Player contents are played while TILE MATRIX is active, the image play timing might have a gap within
monitors.
This function is not available when SCREEN SAVER is active.
Number of monitors arranged horizontally.
Number of monitors arranged vertically.
Select which section of the tiled image to be displayed on the monitor.
Turns the TILE COMP feature on. If YES is set to the TILE COMP, you can adjust a displayed image size and
position by pressing the + button or the - button on the remote control.
Enables the Tile Matrix settings.
When "INPUT" is selected, the TILE MATRIX setting is applied to each signal input.
All settings in the TILE MATRIX are saved for all signal inputs.
All settings in the TILE MATRIX are saved for the selected signal input.
Sets the monitor ID number from 1-100 and group ID from A-J.
The Group ID is made of multiple selections. Also see page 37.
Resets all settings within the MULTI DISPLAY menu back to factory setting.
Set ENABLE or DISABLE. If you set it to ENABLE, set how long the monitor waits to go into power save mode
after signal is lost. For more details, please check the Power Indicator (See page 35).
Set the time when the monitor goes into auto power save mode after signal is lost.
When ENABLE is selected, the monitor will quickly return to the ON state when a signal is detected. Enabling this
option increases standby power consumption.
When ENABLE is selected, you can use USB port for power supply in standby mode.
Shows the actual status of the backlight and temperature sensors.
Use the SCREEN SAVER function to reduce the risk of Image Persistence.
NOTE: When the screen saver is activated, the image will be changed to FULL image. After the screen saver
stops, the image will be reproduced again with the current ASPECT setting.
When the SCREEN SAVER is set to active, STILL, POINT ZOOM, TILE MATRIX, CLOSED CAPTION are not
available.
The brightness of the backlight is decreased when "ON" is selected.
NOTE: Do not select this function when ROOM LIGHT SENSING is set to MODE1 or MODE2.
The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT) at user determined
intervals. You can set interval time and zoom ratio.
Adjusts the color of the side borders when a 4:3 image is reproduced.
By pressing the + button on the remote control, the side borders will become brighter.
By pressing the - button, the side borders will become darker.
Background color of the Media Player window is also changed.
Adjusts the delay time between being in "standby" mode and entering "power on" mode.
"POWER ON DELAY" can be set between 0 and 50 seconds.
When "ON" is selected, the delay time is linked with the Monitor ID. It takes more time when there are a large
number of IDs.
Set ON to activate alert mail. Please refer to Mail Setting (See page 44).
Resets all settings within the DISPLAY PROTECTION menu back to factory setting except for POWER ON
DELAY.
English-32
Advertisement
Table of Contents
