Table of Contents
Advertisement
5 - HANDLING
5.1 - Discharge via forklift truck
The unit is designed to be transported safely by using a forklift
truck. The base features guide rails to accommodate the forks
of the fork-lift truck. These guide rails ensure that the centre of
gravity of the unit remains within the forks, and at the same time,
avoid the possible introduction of the truck's fork into functional
parts that may cause damage to the unit.
206
mm
Note: the module with the heat recovery wheel (BW and RW
assemblies) also includes these guides in its base frame with the
same dimensions.
The recommended length for the forks will be bigger than the unit
width (refer to the following table), so that the entire weight-bearing
structure of the unit can be supported on the forklift truck.
The standards and recommendations of the forklift truck must also
be respected with regards to the maximum load, inclination of the
fork carriage, elevation of the load for transport, and, in particular,
the maximum speed.
Units dimensions for transportation (*):
B1, B2, BF. B3, BX, BP,
BA, BW assemblies
50FF/
FC
Length
Width
Height
Length
(mm)
(mm)
(mm)
020
2.225 1.750 1.230 2.230 1.760 1.975
028
2.225 1.750 1.230 2.230 1.760 1.975
037
2.225 1.750 1.230 2.230 1.760 1.975
040
2.225 1.750 1.230 2.230 1.760 1.975
045
2.225 1.750 1.230 2.230 1.760 1.975
047
2.225 1.750 1.230 2.230 1.760 1.975
052
3.000 2.200 1.230 3.000 2.210 1.995 3.000 2.200 1.230
058
3.000 2.200 1.230 3.000 2.210 1.995 3.000 2.200 1.230
062
3.000 2.200 1.230 3.000 2.210 1.995 3.000 2.200 1.230
070
3.650 2.200 1.230 3.655 2.210 1.995 3.650 2.200 1.230
074
3.650 2.200 1.230 3.655 2.210 1.995 3.650 2.200 1.230
086
3.650 2.200 1.230 3.655 2.210 1.995 3.650 2.200 1.230
093
3.650 2.200 1.230 3.655 2.210 1.995 3.650 2.200 1.230
099
3.650 2.200 1.230 3.655 2.210 1.995
(*) Consult the overall dimensions of the available assemblies in paragraph
7.7 "Recommended service clearance".
Discharge of stacked units
The fi xation set factory-installed for the transport of two stacked
units ensures the safe fi xation of units and the stability of units
during transport.
The discharge of the units on-site will be done via fork-lift truck
with the forks accommodated in the guide rails of the lower unit.
The units must be unstacked after discharging. The simultaneous
handling of both units is not allowed.
The 6 fi xation pieces are fi xed to the units using 4 M8 screws (hex.
key 13). First, unscrew all the screws attaching the pieces to the
8
750mm
206
mm
BT, BB
R1, R2, RP, RW
assemblies
assemblies
Width
Height
Length
Width
(mm)
(mm)
(mm)
(mm)
(mm)
--
--
--
--
--
--
--
--
--
--
--
--
--
--
upper unit. Raise the upper unit with the fork-lift truck to save the
pieces height and then, set down it carefully on the fl oor. Finally,
remove the fi xing pieces from the lower unit by unscrewing the
rest of the screws.
Upper
unit
raised
5.2 - Discharge via crane
Height
Important: This discharge method is not allowed in the case of
(mm)
two stacked units.
--
It is mandatory to follow the lifting instructions given in the drawings
--
provided on the next page.
--
Approved textile slings, suitable for the dimensions and weight
--
of the unit, must be used. A structure with centre of
--
gravity adjustment must also be used to separate the
--
slings from the top of the unit.
Important: slings must be attached to all the marked
rigging points (grips). These points are clearly
identifi ed by labels.
The slings hooks should be fi xed on top of the grips.
All models are provided with 2 lifting grips on each beam, except
the 052 to 099 models with BA and BB assemblies that are
provided with three lifting grips per beam.
--
Raise and set down the unit carefully. Take care not to tilt it by
more than 15°, as this could adversely aff ect its operation.
Safety when lifting can only be guaranteed if all these instructions
are followed. Otherwise, there is a risk of equipment damage or
injury to personnel.
Guide rails for forks
Fixation pieces
Lifting grip
Transport guard
Advertisement
Table of Contents
