Using Keymover; Programming Keymover - One for All URC-8820 B00 User Manual

OFA 8L with Learning Owners Manual.fm Page 14 Monday, January 24, 2005 10:04 AM
O F A 8L U
NE OR LL NIVERSAL
The AUX key is now ready to be
4.
programmed for your second DVD. See
"Setting Up Your Components" on
page 7.
To re-assign other device keys to the AUX
key, repeat steps 1 through 4 by substituting
the sequence from the below chart:
To Re-Assign Perform Sequence
Device
AUX as 2nd SET - 9 - 9 - 2 - TV -
TV key: AUX
AUX as 2nd SET - 9 - 9 - 2 -
VCR key: VCR - AUX
AUX as 2nd SET - 9 - 9 - 2 -
CBL/SAT key: CBL/SAT - AUX
AUX as 2nd SET - 9 - 9 - 2 - CD -
CD key: AUX
AUX as 2nd SET - 9 - 9 - 2 - PVR -
PVR key: AUX
AUX as 2nd SET - 9 - 9 - 2 - AUD -
AUD key: AUX
You can also re-assign another unused
device key by substituting an open key for
the AUX key in the above chart and
performing the sequence. For example, to
re-assign an unused CBL/SAT key as a 2nd
CD key, perform SET - 9 - 9 - 2 - CD -
CBL/SAT. When a re-assignment is done, the
LED (red light) will blink twice to confirm
your choice. At that time, you will need to
program the remote control for the new
device (see "Setting Up Your Components"
on page 7).

USING KEYMOVER

The One For All 8L Universal Remote
Control with Learning (URC-8820 B00)
includes a Keymover feature that allows you
to map (or copy) keys from one mode (i.e.,
14 Using Keymover
R C L
EMOTE ONTROL WITH EARNING
source mode) to another mode (i.e.,
destination mode).
NOTE: The following keys cannot be used as a
source or destination: TV, CBL/SAT, VCR, DVD,
CD, PVR, AUD, AUX, FAV, and SET.
P K
ROGRAMMING
For example, if your VCR does not have
volume control, you can map those keys
(i.e., VOL +, VOL -, and MUTE) from the TV
mode to the VCR mode as follows:
Press and hold SET until the LED (red
1.
light) blinks twice, then release SET.
Enter 9 9 4. The LED will blink twice.
2.
For the source mode, press TV once.
3.
For the source key, press VOL + once.
4.
For the destination mode, press VCR
5.
once.
For the destination key, press VOL +
6.
once.
7. The LED will blink twice, indicating
the keymoved sequence is correct.
8. Repeat steps 1 through 7 twice more to
map remaining volume control keys,
substituting VOL - and MUTE as source
and destination keys in steps 4 and 6.
Upon completion of the above procedure,
you can now use your One For All 8L
Universal Remote Control with Learning
(URC-8820 B00) to control the TV's volume
and MUTE in the VCR mode, as well as in the
TV mode.
R K
ESTORING EYMOVED
S
ETTINGS
Restoring a Single Keymoved Key
1. Press a device key that has a keymoved
key.
EYMOVER
K D
EYS TO EFAULT