’ WNER ANUAL TABLE OF CONTENTS Setup Codes for Cable/PVR/DVR Combos (Códigos de Configuración para Aparatos Combinados Cajas/Convertidores de Cable/PVR/DVR)..44 Introduction ....... .2 Setup Codes for CD Players (Códigos de Features and Functions .
Configuración para Computadoras Centro de functions of the One For All 8L Universal Entretenimiento Multimedia) ....61 Remote Control with Learning (URC-8820 B00).
’ WNER ANUAL HARTS Use the Cursor Keys The LED (red light), to move the cursor in which is located the program guide underneath the and menu screens. POWER Key, blinks to Use OK to choose show that the remote options from your control is working selected device’s...
Page 5
8L U NIVERSAL EMOTE ONTROL WITH EARNING Use CH + (or CH -) to Use the Transport select the next higher Keys to control your (or lower) channel. PVR/DVR, VCR, DVD, or CD player, or VOD (Video On Demand) if available Press PREV once to on your cable or recall the last-viewed...
NOTE: Please refer to the table below when Tuner, Amp, Misc. Audio, performing the instructions in “Setting Up HTIB (Home Theater In Your Components” on page 7. A Box) After programming, the One For All 8L Universal Remote Control with Learning Features and Functions...
8L U NIVERSAL EMOTE ONTROL WITH EARNING INSTALLING BATTERIES Obtain two (2) new AAA alkaline batteries. Match the + and – marks on the batteries to the + and – marks in On the remote control's back, push the battery case, then insert the new down on the top of the battery cover batteries.
2 through 4 and enter the same code COMPONENTS again. Aim the remote control at the device The One For All 8L Universal Remote and press POWER once. The device Control with Learning (URC-8820 B00) is should turn off. If it does not, repeat...
DEVICE CONTROL Aim the remote control at the device and press POWER once. It should turn You can set the One For All 8L Universal off. If the device does not respond, Remote Control with Learning (URC-8820 repeat steps 2 through 4, trying each...
To lock in the code, press and release You can program the M1 and M2 keys on the SET key. The LED blinks twice. your One For All 8L Universal Remote Control with Learning (URC-8820 B00) to To search for the codes of your other...
In its default state, the POWER key on the off. One For All 8L Universal Remote Control Devices will turn on (or off) according with Learning (URC-8820 B00) will to your programmed sequence.
Input on the receiver. This allows you to In its default state, when you press a device still change modes while using the remote. key (e.g., TV) on the One For All 8L Universal Remote Control with Learning NOTE: After executing the Device Key Macro,...
USING LEARNING and cycle through all channels on the selected device. The One For All 8L Universal Remote To stop scanning channels at any time, Control with Learning (URC-8820 B00) press any key once.
(e.g., TV remote control) head-to-head (about 2" apart) from the One For All 8L Universal Remote Control with You can set the One For All 8L Universal Learning (URC-8820 B00). Remote Control with Learning (URC-8820 B00) to control a second TV, VCR, DVD On your original remote control, press player, or other device.
CBL/SAT. When a re-assignment is done, the Upon completion of the above procedure, LED (red light) will blink twice to confirm you can now use your One For All 8L your choice. At that time, you will need to Universal Remote Control with Learning program the remote control for the new (URC-8820 B00) to control the TV’s volume...
CHANGING VOLUME LOCK Enter 9 9 3 and then press VOL - once. The LED will blink four times. The One For All 8L Universal Remote If desired, repeat steps 1 through 3 (of Control with Learning (URC-8820 B00) is...
NIVERSAL EMOTE ONTROL WITH EARNING Volume will again be independently enter it into your One For All 8L Universal controlled according to its default Remote Control with Learning (URC-8820 states for all programmed devices. B00). If the code for your home entertainment or...
’ WNER ANUAL TROUBLESHOOTING PROBLEM: Changing channels does not work properly. PROBLEM: LED (red light) does not SOLUTION: If the original remote blink when you press a control required pressing key. ENTER to change channels, then press ENTER on the SOLUTION: Replace batteries with two remote control after...
B digital or failure caused by products or services not device, pursuant to part 15 of the FCC Rules. supplied by ONE FOR ALL, or which result These limits are designed to provide a from accident, misuse, abuse, neglect,...
WNER ANUAL There are no express warranties except as Copyright 2005 by Universal Electronics listed above. ONE FOR ALL SHALL NOT BE Inc. No part of this publication may be LIABLE FOR INCIDENTAL OR reproduced, transmitted, transcribed, CONSEQUENTIAL DAMAGES RESULTING...