Advertisement
Quick Links
Hitachi Highly
Rollkolbenverdichter
Rotary Compressors
Spezifikation
Installation Manual
WHP09100VUKPA8LT6
R 410A, R 452B - R 454C- R 454B
22,6 cm3/rev
900 - 7200 min-1
DC/ BLDC
RIES GmbH, Rudolf-Diesel-Str. 10, D 64569 Nauheim, GERMANY
Phone: +49 6152 9741 0, Fax: +49 6152 9741 21, Email: info@ries-gmbh.de, Website: www.ries-gmbh.de
Advertisement
Related Manuals for Hitachi Highly WHP09100VUKPA8LT6
Summary of Contents for Hitachi Highly WHP09100VUKPA8LT6
- Page 1 Hitachi Highly Rollkolbenverdichter Rotary Compressors Spezifikation Installation Manual WHP09100VUKPA8LT6 R 410A, R 452B - R 454C- R 454B 22,6 cm3/rev 900 - 7200 min-1 DC/ BLDC RIES GmbH, Rudolf-Diesel-Str. 10, D 64569 Nauheim, GERMANY Phone: +49 6152 9741 0, Fax: +49 6152 9741 21, Email: info@ries-gmbh.de, Website: www.ries-gmbh.de...
- Page 2 Table of Contents First: WHP09100VUKPA8LT6 Specifications —————— 1～4 1.Application range 2.Compressor specifications 3.Motor parameters 4.General characteristics 5.Parts and drawings list Second: the heat pump water heater dedicated compressor use benchmark ——— 5～15 Third: Acceptance basis and rules —————————— 16 1. Acceptance basis 2.
- Page 3 S U B J E C T M o d e l W H P 0 9 1 0 0 V U K P A 8 L T 6 S P E C I F I C A T I O N PAGE：1/30 SCOPE T h i s s p e c i f i c a t i o n i s a p p l i e d to SHANGHAI HIGHLY Heat pump water heater...
- Page 4 *.COP= Heating capacity Motor input *.Rated Capacity and input are measured with HITACHI inverter circuit by secondary Refrigerant calorimeter Methods of JIS B8606 by SHANGHAI HIGHLY Electrical Appliances Co., Ltd. Allowable capacity should be more than 95% of the rated capacity and allowable input should be less than 107% of rated motor input.
- Page 5 S U B J E C T M o d e l W H P 0 9 1 0 0 V U K P A 8 L T 6 S P E C I F I C A T I O N PAGE：3/30 Inductance Ld（mH）...
- Page 6 S U B J E C T M o d e l W H P 0 9 1 0 0 V U K P A 8 L T 6 S P E C I F I C A T I O N PAGE：4/30 PARTS AND DRAWING LIST PARTS NAME...
- Page 7 H E A T P U M P W A T E R H E A T E R C O M P R E S S O R C R I T E R I A PAGE：5/30 COMPRESSOR CRITERIA 1 Strictly observe the specification The compressor should be used in specifications written in this “compressor specification”...
- Page 8 H E A T P U M P W A T E R H E A T E R C O M P R E S S O R C R I T E R I A PAGE：6/30 There should be superheated gas returned to the compressor under all normal operating conditions. T a b l e 2 Item Operating Envelope...
- Page 9 H E A T P U M P W A T E R H E A T E R C O M P R E S S O R C R I T E R I A PAGE：7/30 Condensing temperature 65℃...
- Page 10 H E A T P U M P W A T E R H E A T E R C O M P R E S S O R C R I T E R I A PAGE：8/30 8 Discharge pipe temperature Discharge pipe temperature is measured at a distance 300mm from the surface of compressor and should be less than 110℃.
- Page 11 H E A T P U M P W A T E R H E A T E R C O M P R E S S O R C R I T E R I A PAGE：9/30 14 Impurities in refrigerating system （1）The weight of residue on the inside surface of the heat exchanger and tube should be less than 0.01g/m .
- Page 12 H E A T P U M P W A T E R H E A T E R C O M P R E S S O R C R I T E R I A PAGE：10/30 18 Purge parts with dry nitrogen or dry air to remove remains in parts (dust, detergent, etc.) before assembly of system.
- Page 13 H E A T P U M P W A T E R H E A T E R C O M P R E S S O R C R I T E R I A PAGE：11/30 Moving tubes to the moving parts; minimum clearance 12.7mm(1/2”) Moving tubes to non-moving parts;...
- Page 14 H E A T P U M P W A T E R H E A T E R C O M P R E S S O R C R I T E R I A PAGE：12/30 （6）The compressor can’t be used in the place with corrosive atmosphere such as hot spring and chemical warehouse.
- Page 15 H E A T P U M P W A T E R H E A T E R C O M P R E S S O R C R I T E R I A PAGE：13/30 (14) SHEC will not take any responsibility against accident that is caused by the accessories equipped by yourselves.
- Page 16 H E A T P U M P W A T E R H E A T E R C O M P R E S S O R C R I T E R I A PAGE：14/30 It is necessary to install a dryer to dehumidify the residual moisture mixed in the refrigerant in the cycling system.
- Page 17 H E A T P U M P W A T E R H E A T E R C O M P R E S S O R C R I T E R I A PAGE：15/30 （27）The fuse or/and breaker should be equipped in the main circuit. (28) The thickness of the refrigerating system using tube the tube thickness as followed external diameter(mm)
- Page 18 C h e c k u p o n D e l i v e r y PAGE：16/30 1. Basis for Checking upon Delivery The Performance test will be carried out in accordance with this “compressor Specification”. The Safety Performance in accordance with GB4706.1 Safety of household and similar electrical appliances General requirements and GB 4706.17 Safety of household and similar electrical appliances Particular requirements for motor-compressor.
- Page 19 17/30...
- Page 20 18/30...
- Page 21 . 19/30...
- Page 22 20/30...
- Page 23 21/30...
- Page 24 22/30...
- Page 25 23/30...
- Page 26 24/30...
- Page 27 25/30...
- Page 28 26/30...
- Page 29 （MPa） Pd limit Rotational speed (rpm) R410A R452B/R454B R454C 3.50 3.22 2.25 2400 4.00 3.72 2.75 5400 4.28 4.00 2.97 7200 3.50 3.22 2.25 900～1800 min 27/30...
- Page 30 Chart 2 DC INVERTER COMPRESSOR OIL LEVEL DATUM 28/30...
- Page 31 29/30...
- Page 32 Specification Revision Record Page in Date Revision Reason Conclusion Date Spec 30/30...