Page 1
INDEX (CLICK TO NAVIGATE TO PAGE) PAGE PRECAUTIONARY NOTES INSTALLING 9050 RACK MOUNT RECEIVER INSTALLING 9050 WITH VERTICAL HINGE MOUNTING FRAME INSTALLING 9050TR WITH SLIDE KIT INSTALLING 9050 WITH SLIDE KIT SLIDE MOUNT NOTATION REGARDING U HEIGHT INSTALLING INSTRUMENT BRACKET INSTALLING KEYBOARD TRAY 9050TR PLATFORM REMOVAL &...
FORCEFUL ENGAGEMENT OF THE ITA AND RECEIVER MAY RESULT IN SERIOUS DAMAGE TO MULTIPLE PARTS OF THE SYSTEM (MODULES, RECEIVER, ITA AND CONTACTS). IN THE EVENT OF OPERATIONAL DIFFICULTIES, A TRAINED VPC TECHNICIAN SHOULD BE NOTIFIED TO AVOID ANY POTENTIAL DAMAGE TO THE SYSTEM FROM IMPROPER HANDLING.
9050 USER MANUAL 9050 RACK MOUNT RECEIVER INSTALLATION PART # 310 104 368, 310 104 429 TOOLS REQUIRED Phillips Head Screwdriver INSTALLATION INSTRUCTIONS Install clip/cage nuts on rack, to correlate with mounting holes and captive screws on receiver. Place receiver up to clip/cage nuts on rack, making sure they are aligned (Figure A).
9050 USER MANUAL INSTALLING 9050 WITH VERTICAL HINGED MOUNTING FRAME PART # 310 113 613, 310 104 368 TOOLS REQUIRED Phillips Head Screwdriver ³/ Allen Wrench NOTE: Due to the weight of the VHMF (approx 15 lbs.) versus the receiver (approx.
SLIDE INSTALLATION Figure A. Each set of slides supports an instrument bracket (shelf) The height and weight of the 9050 and 9050TR require the use of 2 sets of for easy test chassis access. slides for full support. Determine the desired approximate rack location to mount receiver and platform.
Page 6
The receiver may now be unscrewed from the rack and moved out from the rack on the slides, if desired. ALWAYS SUPPORT THE RECEIVER AND PLATFORM Figure H. WITH THE MOST ROBUST (MIDDLE) SECTION OF THE SLIDES. RETURN TO INDEX For more information visit vpc.com 07/19/2022...
Page 7
SLIDE INSTALLATION for easy test chassis access. The height and weight of the 9050 and 9050TR require the use of 2 sets of slides for full support. Determine the desired approximate rack location to mount receiver and platform. The 9050 includes 2 instrument brackets, one for each tier, that can support a test chassis for close proximity access (Figure A).
Page 8
9050 USER MANUAL INSTALLING 9050 WITH SLIDE KIT (CONT’D) PART # 310 104 402, 310 104 483, 310 113 451, 310 113 411, 310 113 500 Remove the innermost section of each slide by extending the slides fully, depressing the blue tab, and continuing to extend the inner sections of each slide until it is free from the slide assembly (Figure E).
Page 9
PART # 310 104 369, 310 104 402, 310 104 483 With certain receivers including the 9050/ 9050TR, the slide mechanism protrudes downward slightly into the next U height on both sides of the receiver. Please make any necessary adjustments to U height when planning your test rack layout.
Page 10
Tighten the slide mounting screws. MAKE SURE ALL MOUNTING SCREWS HAVE BEEN SECURELY TIGHTENED. ONLY USE 8-32 BUTTON HEAD SCREWS. RETURN TO INDEX For more information visit vpc.com 07/19/2022...
MOUNTING BRACKET, LEFT MOUNTING BRACKET, RIGHT 13.0 [330.2] USB KEYBOARD CONNECTOR. 12 INCH SLIDES 28.4 [721.36] RUBBER GROMMET 12 INCH SLIDE MOVEMENT KEYBOARD WITH TOUCHPAD KEYBOARD TRAY 13.3 [337.82] [30.48] Figure A. RETURN TO INDEX For more information visit vpc.com 07/19/2022...
Page 12
Figure B. Fully extend the keyboard slides to access the mounting holes for the self- locking fasteners. Figure C. The different hole patterns allow for variations in the overall position of the keyboard. RETURN TO INDEX For more information visit vpc.com 07/19/2022...
Page 13
10-32 mounting screws. Figure C. The brackets will be securely attached to the slides after the mounting screws are installed. RETURN TO INDEX For more information visit vpc.com 07/19/2022...
Page 14
Install the handle into the left side hole at the preferred 90° position (Figure C). Replace the screw and handle washer into the cavity on right side of the receiver. Figure B. Remove handle from standard right side. Figure C. Install handle on left side. RETURN TO INDEX For more information visit vpc.com 07/19/2022...
Page 15
MICROSWITCH REMOVAL AND INSTALLATION PART # 310 113 200 NOTE: A microswitch may be used in VPC receivers to determine the presence (or absence) of an engaged ITA in the system. It is typically configured so that power to the interface is turned off when there is no ITA present.
Page 16
NOTE: VPC offers several standard ITA enclosures, as well as custom enclosures. The 9025, 25 module ITA enclosure, is compatible with the 9050 if a smaller ITA enclosure is desired. Visit vpc.com for all available options for the 9050 and 9025 ITA.
Page 17
Modules must be installed so that Pin 1 of each respective mating receiver and ITA module pair are adjacent. VPC recommends that Pin 1 be positioned to the left in the receiver and ITA frames. All ITA modules must match the respective receiver modules. It is crucial for all modules to be installed properly.
• See above troubleshooting steps ITA will not engage with the receiver after attempting above troubleshooting steps. Contact VPC – unauthorized user adjustments to the system will void the warranty. No continuity upon engagement. • When replacing an ITA contact, the mating contact on the receiver side should also be inspected and replaced if necessary.
Need help?
Do you have a question about the 9050 and is the answer not in the manual?
Questions and answers