Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for HYTROL PCH
Summary of Contents for HYTROL PCH
- Page 1 Installation Maintenance Manual with Safety Information and Parts List RECOMMENDED SPARE PARTS HIGHLIGHTED IN GRAY Effective March, 1995 Model PCH (Supercedes November, 1993) Bulletin #429 Use code HYPMANUAL for free shipping on your first order at HytrolParts.com...
-
Page 2: Table Of Contents
Operation Safety Precautions ..9 Model PCH Parts List ....15 Conveyor Start-Up ....9... -
Page 3: Introduction
INTRODUCTION This manual provides guidelines and procedures for installing, the manual. For safety to personnel and for proper operation operating, and maintaining your conveyor. A complete parts of your conveyor, it is recommended that you read and follow list is provided with recommended spare parts highlighted in the instructions provided in this manual. -
Page 4: Conveyor Set-Up
Conveyor Set-Up to be removed and reinstalled through the sup- 1. . . Determine direction of product flow. Figure 4A indi- port pivot plates. Since the track is bolted to the cates the flow as related to the drive. frame with these bolts, care must be taken not 2. - Page 5 15" 15" 15" 15" CONVEYOR CONVEYOR ITEM ITEM HYTROL CONVEYOR CO. INC. HYTROL CONVEYOR CO. INC. JONESBORO, AR • ST. LOUIS, MO • MANTECA, CA JONESBORO, AR • ST. LOUIS, MO • MANTECA, CA “MATCH-MARK” NUMBERS FIGURE 5C BUTT COUPLINGS...
-
Page 6: Belt Installation
Belt Installation 1. . . Remove chain guard and drive chain to allow drive sprockets to turn freely during belt installation. NOTES (Figure 7A). BELTS ALLOWED TO OPERATE WITH 2. . . Remove end cap. (Figure 7B). TOO MUCH TENSION is usually indicated 3. - Page 7 Belt Installation (Continued) FIGURE 7A FIGURE 7C FIGURE 7B "Building Relationships One Conveyor Part at a Time" support@hytrolparts.com | www.HytrolParts.com...
-
Page 8: Electrical Equipment
Electrical Equipment or are beyond voice and visual contact from drive areas, WARNING! loading areas, transfer points, and other potentially haz- Electrical controls shall be installed and ardous locations on the conveyor path not guarded by wired by a qualified electrician. Wiring location, position, or guards, shall be furnished with information for the motor and controls are emergency stop buttons, pull cords, limit switches, or... -
Page 9: Operation
OPERATION Operation Safety Precautions A) Only trained employees shall be permitted to operate F) A conveyor shall be used to transport only material it conveyors. Training shall include instruction in operation is capable of handling safely. under normal conditions and emergency situations. G) Under no circumstances shall the safety characteris- B) Where employee safety is dependent upon stopping tics of the conveyor be altered if such alterations would... -
Page 10: Maintenance
SAE-30 wt. oil and REDUCERS that the belt wings be greased with a good grade of MANUFACTURED BY HYTROL: See separate manual bearing grease approximately every 40 hours of opera- in Packing Envelope that contains lubrication and main- tion. -
Page 11: Drive Chain Alignment And Tension
Drive Chain Alignment and Tension The drive chain and sprockets should be checked peri- FIGURE 11A odically for proper tension and alignment. Improper adjustment will cause extensive wear to the drive com- ponents. STRAIGHT EDGE TO MAKE ADJUSTMENTS 1. . . Remove chain guard. -
Page 12: Trouble Shooting
Motor or reducer overheating. level. 2) Low voltage to motor. 2) Have electrician check and correct as necessary. 3) Relubricate per manufacturer’s recommendations. For HYTROL 3) Low lubricant level in reducer. reducer, refer to separate manual TROUBLE SHOOTING BELT TROUBLE... -
Page 13: Preventive Maintenance Checklist
HYTROL Distributor. SERIAL # 775544 Give Conveyor Model Number and Serial Number or 2. . . HYTROL Serial Number HYTROL Factory Order Number. (Located near Drive Give Part Number and complete description from Parts 3. . . on Powered Models) List. -
Page 14: Model Pch Parts Drawing
Model PCH Parts Drawing SECTION “B-B” "Building Relationships One Conveyor Part at a Time" support@hytrolparts.com | www.HytrolParts.com... -
Page 15: Model Pch Parts List
Model PCH Parts List Ref. No. Part No. Description Ref. No. Part No. Description — Motor—C-Face, Foot Mounted — B-0666-048 48 in. Long — 030.7224 3/4 HP—230/460 VAC—3 Ph.—60 Hz.—TEFC — B-06666-072 72 in. Long — 030.7324 1 HP—230/460 VAC—3 Ph.—60 Hz.—TEFC —... - Page 16 "Building Relationships One Conveyor Part at a Time" support@hytrolparts.com | www.HytrolParts.com Use code HYPMANUAL for free shipping on your first order at HytrolParts.com "Building Relationships One Conveyor Part at a Time" support@hytrolparts.com | www.HytrolParts.com...
Need help?
Do you have a question about the PCH and is the answer not in the manual?
Questions and answers