Stanley Magic-Swing HDLE Quick Reference Manual
  1. Manuals
  2. Brands
  3. Stanley Manuals
  4. Controller
  5. Magic-Swing HDLE
  6. Quick reference manual
Stanley Magic-Swing HDLE Quick Reference Manual

Stanley Magic-Swing HDLE Quick Reference Manual

Microprocessor control box
Hide thumbs
Table of Contents

Advertisement

Quick Links

Stanley Access Technologies
Quick-Reference Guide
Magic-Swing
Prohibition on Copying
Any unauthorized reproduction, disclosure or distribution of copies by any person of any
portion of this work may be a violation of copyright law of the United States of America
and other countries, could result in the awarding of statutory damages of up to $250,000
(17 USC 504) for infringement, and may result in further civil and criminal penalties. All
rights reserved.
   
and Magic-Force
Microprocessor Control Box
Quick-Reference Guide
203959
Rev. F, 10/2/02
   
HDLE/FE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Magic-Swing HDLE and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Stanley Magic-Swing HDLE

Summary of Contents for Stanley Magic-Swing HDLE

  • Page 1 Stanley Access Technologies Quick-Reference Guide         Magic-Swing and Magic-Force HDLE/FE Microprocessor Control Box Quick-Reference Guide 203959 Rev. F, 10/2/02 Prohibition on Copying Any unauthorized reproduction, disclosure or distribution of copies by any person of any...

  • Page 2: Table Of Contents

    Attachment 7, Wiring Diagram—HDLE/FE Control Box with Sentrex ............20 Attachment 8, DIP Switch S2 Mode Settings ..................... 21 Attachment 9, HDLE/FE Control Box........................ 23 203959 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED. Rev. F, 10/2/02 1 of 23...

  • Page 3: Purpose

    This manual covers operation of HDLE/FE (black-label) control boxes only. For yellow- label control box operating instructions, refer to Stanley Access Technologies document No. 203821, "Magic-Swing Microprocessor Control Box."...
  • Page 4 One-Piece Switch Module: On Magic-Force operators, the individual breakout, breakout status, close check, and auxiliary switches have been replaced with a single one-piece switch module. 203959 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED. Rev. F, 10/2/02 3 of 23...

  • Page 5: Precautions

    • CONNECT power pigtail assembly white wire to white (neutral) service wire. 3.2.8 ENSURE power pigtail assembly is not connected to main harness connector J1. 203959 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED. Rev. F, 10/2/02 4 of 23...

  • Page 6: Connecting Breakout Status Signal Wiring (Magic-Swing Operators)

    Using a wire nut, CONNECT remaining wire from first operator to remaining wire on second operator. 3.3.8 VERIFY breakout status/breakout cam is properly set as follows: 203959 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED. Rev. F, 10/2/02 5 of 23...
  • Page 7 Using a multimeter, CHECK continuity between TB1 terminals 6 and 8, and ENSURE there is an open circuit. g. RELEASE door. h. PLUG TB1 into control box circuit board. 203959 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED. Rev. F, 10/2/02 6 of 23...

  • Page 8: Connecting Breakout Status Signal Wiring (Magic-Force Operators)

    8 of control box connector TB1. • CONNECT remaining two yellow breakout status switch wires together with a wire nut. 3.4.4 VERIFY breakout status/breakout cams are properly set as follows: 203959 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED. Rev. F, 10/2/02 7 of 23...
  • Page 9 ROTATE CLOSE CHECK CAM COUNTERCLOCKWISE UNTIL RAISED PORTION OF CAM ACTUATES SWITCH, THEN ROTATE CAM 10 DEGREES CLOCKWISE. ROTATE AUXILIARY CAM AS DESIRED. DETAIL B: LEFT HAND OPERATOR CAM SETTINGS MF0026 203959 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED. Rev. F, 10/2/02 8 of 23...

  • Page 10: Wiring The Operator Switch Module (Magic-Force Operators)

    CONNECT wiring to auxiliary position switch terminal block as shown. c. SLIDE switch module into operator housing until switch module release lever snaps into place. 203959 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED. Rev. F, 10/2/02 9 of 23...

  • Page 11: Wiring The Operator For Required Handing (Magic-Force Operators)

    3.7.1 Refer to Attachment 5, and CONNECT “ON/OFF/HOLD OPEN” switch wiring as follows: TB1 Terminal Connection Switch Wire Color Common Yellow Operate Orange Sensors Violet 203959 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED. Rev. F, 10/2/02 10 of 23...

  • Page 12: Wiring The Door Activation Or Safety Device

    Refer to Figure 5, and CONNECT wiring for counter. Figure 5. Counter Wiring COUNTER MCB005 BLACK TUNE-IN INSTRUCTIONS Initial Tune-In Settings 4.1.1 DISCONNECT power pigtail assembly. 203959 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED. Rev. F, 10/2/02 11 of 23...

  • Page 13: Final Tune-In Adjustments

    CYCLE and RECYCLE door several times to verify proper speeds and forces, and PERFORM adjustments in the following order: a. ADJUST close check cam. b. ADJUST open speed potentiometer. 203959 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED. Rev. F, 10/2/02 12 of 23...
  • Page 14 ADJUST Magic-Touch time delay rotary switch. IF the Magic-Touch time delay is set to 2 seconds, INSTALL and ADJUST safety sensor. k. ADJUST breakout and breakout status cams. 203959 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED. Rev. F, 10/2/02 13 of 23...

  • Page 15: Attachment 1, Breakout Status Wiring

    SEEN FROM WIRES SIDE) OPERATOR NO. 2 BREAKOUT STATUS WIRING--SINGLE DOOR BREAKOUT STATUS WIRING--DUAL DOOR NOTE: MCBA017 REMOVE CONTROL BOX JUMPER WIRE FROM TERMINALS 6 AND 8. 203959 Rev. F, 10/2/02 Page 14 of 23 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED.

  • Page 16: Attachment 2, Magic-Force Operator Wiring-Dual Operators With Dual-Adjustment Closing Speed Controls And Switch Modules

    SPEED CONTROL P/N 516660 NOTE CONFIG URATION ON EARLY ENCODER MODEL O PERATOR ASSEMBLIES. ENCODER WHITE WHITE 203959 Rev. F, 10/2/02 GREEN GREEN DETAIL B Page 15 of 23 SEE DETAIL B (SEE NOTE) MCBA20 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED.

  • Page 17: Attachment 3, Magic-Force Operator Wiring-Dual Operators With Dual-Adjustment Closing Speed Controls, Power Close Modules, And Switch Modules

    CONFIGURATION ON EARLY MODEL OPERATOR ASSEMBLIES. ENCODER ENCODER 203959 WHITE WHITE Rev. F, 10/2/02 GREEN GREEN DETAIL B Page 16 of 23 SEE DETAIL B (SEE NOTE) © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED. POWER CLOSE MODULE P/N 516116 MCBA21...

  • Page 18: Attachment 4, Magic-Swing System Wiring-Main Power, Motor(S), And Encoder(S)

    (STACKED ON BOTTOM) ENCODER WHITE WHITE R-20 (FOR LIGHT SPRING OPERATORS) 1 GREEN BLUE SW-1, BREAKOUT 2 BLACK MOTOR 3 WHITE YELLOW BLACK MCBA002 203959 Rev. F, 10/2/02 Page 17 of 23 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED.

  • Page 19: Attachment 5, Signal Wiring- Hdle/Fe Control Box With Carpets, Pushplate, Operate Sensor, Or Safety Sensor

    TB1, TERMINALS 6 AND 8. REMOVE CONTROL BOX JUMPER WIRE FROM TERMINALS 6 AND 8. IF DUAL OPERATORS, CONNECT YELLOW OPERATOR WIRES IN SERIES BEFORE CONNECTING TO TERMINALS 6 AND 8. 203959 Rev. F, 10/2/02 Page 18 of 23 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED.

  • Page 20: Attachment 6, Wiring Diagram- Hdle/Fe Control Box With Bifold Doors

    5. ALL SENSOR SIGNAL OUTPUTS ARE DEFINED WITH THE POWER ON. 6. SEE ATTACHMENT 2 FOR STANDARD OPERATOR WIRING. SEE ATTACHMENT 3 FOR POWER CLOSE OPERATOR WIRING. WIRE BREAKOUT STATUS AS SHOWN. 203959 Rev. F, 10/2/02 Page 19 of 23 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED.

  • Page 21: Attachment 7, Wiring Diagram-Hdle/Fe Control Box With Sentrex 3

    SET DIP SWITCH S2 POSITION 1 TO OFF FOR TIMER MODE GREEN (SEE DIP SWITCH S2 WHITE MODE SETTINGS ATTACHMENT.) BLACK SENTREX FLEX LINK MCBA007 SENTREX TERMINALS 203959 Rev. F, 10/2/02 Page 20 of 23 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED.

  • Page 22: Attachment 8, Dip Switch S2 Mode Settings

    OFF=15 OFF=15 3 4 5 6 3 4 5 NOTE: BLACK INDICATES SWITCH POSITION. MCBA019_1 EXAMPLE: INDICATES SWITCH POSITION 1 IS SET TO ON. 203959 Rev. F, 10/2/02 Page 21 of 23 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED.
  • Page 23 BIFOLD APPLICATION, DUAL DOOR, FOUR-PANEL OPEN CHECK SIZE: OPEN CHECK SIZE: ON=10 (NORMAL) ON=10 (NORMAL) OFF=15 OFF=15 3 4 5 3 4 5 MCBA019_2 203959 Rev. F, 10/2/02 Page 22 of 23 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED.

  • Page 24: Attachment 9, Hdle/Fe Control Box

    ON=10° open check, OFF=15° open check WARNING: When set to 2-second time ON=High Magic-Touch sensitivity delay, a safety sensor must be installed to OFF=Low Magic-Touch sensitivity ensure ANSI compliance. 203959 Rev. F, 10/2/02 Page 23 of 23 © 2002, THE STANLEY WORKS. ALL RIGHTS RESERVED.

This manual is also suitable for:

Magic-swing hdfeMagic-force hdleMagic-force hdfe

Table of Contents