Test Operation - Panasonic DH-3RL2 Operating Instructions Manual

6. How to fix the Front Plate
① Make sure the Main Switch Knob and the Power Selector Knob on Front Plate
it is at "Off" position.
② Make sure the "D-Cut" position of the Rotary Shaft Shaft are located as shown.
③ Close the Front Plate of the Unit according to the sequence as illustrated.
④ Push in the Main Switch Knob and the Power Selector Knob until it is fully inserted
<Main Switch Knob and Power Selector Knob can not be inserted if Step ①
and Step ② is not done accordingly>
⑤ Fix the Screw at the bottom of the Unit.
Note:
1. Do not push the ELB Test Button during fixing the Front Plate.
2. Do not apply extreme force to insert the Main Switch Knob and
the Power Selector Knob during fixing the Front Plate because
it will damage the switch inside the Unit.
7. Shower Hanger Installation
① Install the Rail Holder so that the Shower Head
height not higher than the Unit top.
Make sure the wall level must be same to the Rail
Holder fixing position. If the wall is not at the same level,
please use spacer (not included) to fix the accessory.
Rail Holder
Shower Head
④ Tighten the Shower Hanger with
Shower Hanger Knob.
Shower Hanger
Sliding Rail
Shower Hanger
Knob
Hole to fix Shower Head
Top
Bottom
* Shower Hanger will drop off easily
once the knob is loosen.

3. TEST OPERATION

1. • Before switch "ON" electricity supply, please check the electrical wiring connection to the Unit.
• Switch "ON" the Miniature Circuit Breaker (MCB) and ON/OFF DP (double pole) Switch.
• Set the ELB of the Unit to "On". (Push up the ELB Reset Lever if it is down)
• Press the ELB Test Button.
• It is normal if the ELB turns "Off" (the ELB Reset Lever falls) and push the ELB Reset Lever up.
Refer figure as shown.
• Inspect the built-in ELB (once a month) to avoid a hazard to users such as damage to property,
serious injury or death.
If the ELB Reset Lever cannot be reset even if you push it up or if it soon slides down
during operation, please do not use the Unit and contact the authorized dealer
immediately to avoid a hazard to users such as damage to property, serious injury or
death. Never fix the ELB Reset Lever forcibly with tape and such.
2. • Turn on the Main Water Valve.
• Turn the Water Volume Knob clockwise and water will flow out from the Shower Head.
• Check if water leaks from Pipe Line.
3. • Turn the Main Switch Knob "On" (ELB light will turn red).
• Turn the Power Selector Knob clockwise and hot water will flow out from the Shower Head.
(Adjust to suitable water temperature).
4. • Refer detail for HOW TO USE and WATER FLOW RATE ADJUSTMENT on page 5.
② Install the Upper Rail Holder on the wall
but not higher than the Unit top. Tighten
the Upper Rail Holder with 2 screws.
(Make sure to insert the Wall Plugs
through the screw holes).
ELB
Lo Med
Off Hi
ELB Test Power Selector
Off On
Screw
Main Switch
OFF Upper Rail Holder
MAX
FILTER
CLEANING
⑤ Install the Lower Rail Holder ⑥ Cover the Upper and Lower
with the groove of Sliding Rail
inserted to the Upper and
Lower Rail Holder's notches.
Tighten the Lower Rail Holder
with 2 screws (Make sure to
insert the Wall Plugs through
the screw holes).
Sliding Rail
Rail Holder
Groove
Notch
WARNING
- 11 -
①
Front Plate
ELB
Lo Med
Off Hi
Power Selector
Off On
Main Switch
Main Switch Knob
and Power Selector Knob
③ ④
Front Plate
Back Plate
Press
Press
Press
③ Prepare the Shower Hanger and Sliding Rail,
remove the Shower Hanger Knob by turning it
(anticlockwise) then install the parts following
the number (1), (2), (3) and (4). Note: Make sure
hole of Shower Hanger (1) is align with hole of
Shower Hanger (2) and slot the Sliding Rail.
Shower Hanger
Knob
ELB
d
Me
Lo
Off
(4)
⑦ Adjust the Shower Hanger at the
Rail Holder with the Rail required level and hang the Shower
Holder Covers. Head as shown in diagram below.
Upper Rail
Holder Cover
Upper Rail Holder
Lower Rail Holder
Lower Rail
Holder Cover
Back Plate
②
"D-Cut"
WARNING
L(+) (-)N
MUST BE TIGHTEN
Position
Screw
Sliding Rail
(3)
Shower Hanger
(1)
Hole align
(2)
Shower Head
Shower Hanger
Tighten the Screw if
Shower Head moves
downward.
ELB
ELB
Lo Med
Test Button
Off Hi
Power Selector
ELB Test
Off On
ELB Reset
Push Up Main Switch
DH-3RL2
ELB
FILTER
Reset Lever CLEANING
Push