How To Use Electric Home Shower; How To Use; Water Flow Rate Adjustment - Panasonic DH-3RL2 Operating Instructions Manual

HOW TO USE ELECTRIC HOME SHOWER

1. HOW TO USE

1. Turn the Water Volume Knob clockwise to turn on the water (make sure the Main Water Valve is on).
(Water will flow out from Shower Head at inlet water temperature).
2. Switch on the Miniature Circuit Breaker (MCB) and ON/OFF DP (double pole) Switch.
3. Push the ELB Reset Lever if it is down.
4. Turn the Main Switch Knob to "On" (ELB light will turn red).
5. The shower temperature can be controlled by turning the Power Selector Knob.
Set the Power Selector Knob to the desired position.
(a) When the Power Selector Knob is set at "Off", the Power is cut off and outlet temperature same with
inlet water temperature.
(b) When the Power Selector Knob is set at "Lo", Power Level is low.
(c) When the Power Selector Knob is set at "Med", Power Level is medium
(d) When the Power Selector Knob is set at "Hi", Power Level is high
6. After using this Unit, please turn off the Main Switch Knob and turn off the water supply
by turning the Water Volume Knob anticlockwise until the water flow is completely stopped.
Note: In case of no water supply, close the Water Volume Knob by turning it anticlockwise and make
sure the Main Switch Knob and the Power Selector Knob is in "Off" condition (ELB light is off).
This to prevent unnecessary water flow from Shower Head after the water supply recovered.
CAUTION
7. Shower Head can be set to various position.
(a) Loosen Shower Hanger Knob and adjust higher or lower.
Tighten Shower Hanger Knob.
(b) Loosen Shower Hanger Knob and Shower Hanger can be
adjusted to the left or right. Tighten Shower Hanger Knob.
(c) The angle of Shower Head can be adjusted by moving the
Shower Head upper or lower.

2. WATER FLOW RATE ADJUSTMENT

(1) Maximum water flow rate can be adjusted by using Main Water Valve.
Step 1: Turn "OFF" the Main Water Valve.
Step 2: Turn the Shower Head upward at waist height.
Step 3: Turn the Water Volume Knob clockwise to maximum volume position.
Step 4: Gradually turn "On" the Main Water Valve and adjust the splashing height (H) of the shower.
It is recommended to adjust the water splashing height (H) at 100 cm ~ 110 cm (approximately 3 L/min).
Note: 1. After setting maximum flow rate, please use Water Volume Knob to turn on and turn off the water supply.
2. Pay attention to shower temperature when reducing the volume of water.
The shower temperature will become very hot if the water flow rate is too low.
3. In case of continuous usage at high temperature setting, water temperature will increase and the control
device will activate temporary resulting the water temperature to drop.
Do not block the Shower Head with hand, towel
or bend the Shower Hose. The water flow rate
will drop and water temperature may become
very hot.
H = 100 cm ~ 110 cm
Waist Height
Floor
- 5 -
(a)
Shower Hanger
Knob
Shower
Hanger
ELB Water Volume
Lo Med
Knob
Off Hi
Power Selector
ELB Test
Off On
ELB Reset
Push Up Main Switch
DH-3RL2
Main Water
OFF
MAX
Valve
FILTER
CLEANING
ELB
Lo Med
Off Hi
Power Selector
ELB Test
Off On
ELB Reset
Main Switch
Push Up
DH-3RL2
ELB
ELB
Lo Lo Med Med
ELB: On condition
Off Off Hi Hi
Power Selector Power Selector
ELB Test ELB Test
Off Off On On
ELB Reset ELB Reset
Push Up Push Up Main Switch Main Switch
DH-3RL2 DH-3RL2
ELB: Off condition
ELB
Lo Med
Off Hi
Power Selector
Off On
Main Switch
(b) (c)