Page 5
3.装置への取り付け・取り外し 下記の手順にて装置に取り付けを行ってください。 ● 取り付ける装置の説明書を参照し、「安全上のご注意」、「取り扱い上のご注意」を守って 取り付け・取り外しを行ってください。 ※本製品をT110d、T120dに取り付けることにより、本体外形寸法が以下となります。 200.0 mm (幅) X 613.5 mm (奥行き) X 438.0 mm (高さ) (突起物含まず) 1. フロントベゼルを開いて、上方向にスライドさせ、 フロントベゼル 取り外してください。 ② ① 2. デバイスドアを開いて、上方向に デバイスドア スライドさせ取り外してください。 ② ① 3. 前項のデバイスドアの取り外しと 防塵ドア 逆の手順で防塵ドアを取り付けます。 ① ②...
Page 6
4. アクセントカバーのツメ2箇所を押してフロントベゼルから外します。 ① アクセントカバー 矢印の方向にツメを押して アクセントカバーを外す。 ② ① 5. 目詰まりセンサケーブルのコネクタをマザーボードの接続コネクタに接続します。 目 詰 ま り セ ン サ 接続用コネクタ 目 詰 ま り セ ン サ 接続用コネクタ...
N8146-28 Dust Proof Kit with Sensor for Tower-model Server User's Guide Preface Thank you very much for your purchase of this product. The guide is intended to allow you to install and use the product correctly and safely. Read the guide carefully before handling the product.
Safety Precautions Observe the following notes to use the product safely. WARNING If smoke, odor, or noise is present, immediately turn off the server and disconnect the power plug from the outlet, then contact the store where you purchased the product or your maintenance service company.
Transfer to Third Party Make sure to provide all accessories including this manual along with the product to a third party. Disposal Dispose of this product according to all national laws and regulations. Dispose of this product as plastic garbage.
Page 16
1.Notes on Using the Product ● This product is dedicated to Express5800/T110d and T120d servers. ● This product has an effect only in the prevention from dust invasion. It has no effect in damage from salt and corrosive gas. 2.Components Check components according to the list below.
Page 17
3.Installing/Removing the Product to the Server Take the steps below to install the product to the server. ● Read the sections "Safety Precautions" and "Handling precautions" in the User's Guide of the target server to install or remove the product safely and properly. Note: The outer dimension of T110d or T120d is as follows after the product is installed.
Page 18
4. Push claws (2 places) on accent cover, and remove the accent cover from front bezel. ① Accent cover Push claws toward the direction shown by an arrow in the figure below to remove the accent cover. ② ① 5. Connect the sensor cable to the connector on motherboard. Connector for sensor cable Connector for...
Page 19
6. Route the sensor cable as shown in the figure below. Upper of front panel Pull the cable out from upper of front panel. Remove the sub-bezel, and connect the cable. Clamp a cable in four places of the ○ mark. Install the sub-bezel.
Page 20
8. Install the front bezel to server chassis. Insert the tip of hinge into the holes on chassis (3 places). ① ① ② Pull the cable out to the front of front bezel.
Page 21
9. Connect the cable to monitoring sensor. 10. Install the dust proof cover to the front bezel in reverse procedure of removal of accent cover. Dust proof cover ② ①...
Page 22
4.Replacement of Dust Proof Filter The service life of dust proof filter is six months (recommended) or one year (maximum). The life time depends on usage environment. Use N8147-24 Dust proof filter for replacement. ● If the server is operated for long time beyond the maximum service life, the temperature inside the device raises due to clogged dust, and may cause a device failure.
Page 23
2.Replacement of Dust Proof Filter 2.1 Remove the dust proof filter from inside of dust proof cover. Remove the filter while holding the tab. Dust proof filter 2.2 In the reverse procedure of removal, mount the filter to dust proof cover so that its tab faces toward you.
Page 24
Remarks (1) No part of this manual may be reproduced in any form without the prior written permission of NEC Corporation. (2) The contents of this User's Guide may be revised without prior notice. (3) The contents of this User's Guide shall not be copied or altered without the prior written permission of NEC Corporation.
Need help?
Do you have a question about the N8146-28 and is the answer not in the manual?
Questions and answers