olympia electronics GR-796/ST/DUO/ADR Quick Start Manual

battery. When the charge is finished, the luminaire
Package Contents
will perform an automatic autonomy test which lasts
1 Luminaire for the stated duration. If the battery is in good
1 Lens Accessories condition then the LED indicator will turn off.
1 Set of Mounting Springs
1 Addressable Communication
Manual
2 Labels for 3 & 8 hours duration The luminaire has the ability to be connected to the
Olympia Electronics addressable panels. In order to
General
do so, the luminaire's address has to be unique in
the same bus. For the different address dip switch
o
These devices are used indoors (ta 40 C) in places settings, see the extra leaflet.
where emergency light is needed. Each device must
ΑΤΤΕΝΤΙΟΝ!!!
be permanently connected to mains power supply.
In normal operation the battery is charging. In case 1. Operations for installation, maintainance or
of a mains power supply failure, the device enters testing must be done by authorized personnel
emergency mode and the illumination LED turns on. only.
When the mains power supply is restored the 2. Always use in any case round mains cable, with a
diameter of 5-10mm (H05RN-F type 2x1mm² or
device turns to normal operation.
any other type, at least equal to it's mechanical
Automatic Operational Test and electrical properties). ATTENTION!! The cable
This test is conducted automatically every 15 days must not be deformed in any way (This
and lasts 3 seconds. The light source and the requirement is important to ensure the ΙΡ rating).
3. The device must be connected to the mains
emergency circuit of the device are tested. The test
can be conducted only if the mains power supply power supply through a circuit breaker that is
and the battery are connected. During this test depends on the total line's power load.
period the light source will light up and the green 4. In case of battery replacement, it must be
replaced by the same type, by the manufacturer
LED will flash quickly. The battery must have
or a competent person.
adequate charge.
5. In case of inactive use for a period greater than 2
Automatic Autonomy Test months, disconnect the battery by pulling out the
The Automatic Autonomy Test is conducted every 6 battery's connector.
6. I t i s not allowed to discard batteries into
months and measures the device's back up
common trash bins, they must be discarded
operation and emergency duration. In order to be
performed, the mains power supply should be only
connected and the battery should be fully charged. incinerate.
During this test period the light source will light up
and the green LED will flash quickly. This test lasts for
the stated duration. In case the test shows a battery
fault, then the battery needs to be replaced. After
the replacement, the luminaire will charge the
Indications LED Status
GREEN RED Description
(charge) (Batt./Lamp
Fault)
Normal
Charging
(battery test not possible whilte charging)
Mains off
(battery not connected or charger fault)
Battery Test (Duration: 1h, 3h, 8h)
Battery Fault
Light Source Test (Duration: 3s)
Light Source Fault
Battery Fault & Light Source Fault
Indications
Green LED
(Charge)
1
Dimensions
130mm
Lens Installation
Anti-Panic
in battery recycling points. Do not
Escape Route
Note:
Permanently
ON
Fast Blink
Slow Blink
Off
In order to place the proper lens (Anti - Panic or Escape Route), first be sure that the luminaire is
not connected in the mains power supply and the battery is disconnected. Place the proper lens
and retaining cover on the luminaire. Be careful not touch the LED with your hand.
In order to change the lens, be sure that the luminaire is not connected to the mains power
supply and the battery is disconnected. Use a flat bladed screwdriver to remove the retaining
Red LED
cover, remove the placed lens and insert the new one with its retaining cover.
(Battery/Lamp Fault)
Be careful not to touch the LED with your hand.
2
923796000_09_001
6.3mm
30mm
Ceiling opening
118mm
121mm
923796000_09_001
Οδηγίες Εγκατάστασης Installation Instructions
Install the 2 springs contained in the package to the bottom cover of the luminaire. Install
them as shown in the Figure.
1
Place a flat blade screwdriver on the 5 marked positions and swift it, pull up gently the
bottom cover and remove it.
2
Dip Switch Positions (DS1)
1 2 3 4
1h
(default position)
The user can select one of the 3 available minimum autonomy
durations: 1 hour, 3 hours and 8 hours. The selection must be
done while the luminaire is disconnected from AC and battery
supplies. The selection is achieved through Switches 2 & 3 of
DS1. Switches 1 and 4 are not used.
Two additional labels are included in the package, one for 3 hours duration (180) and one for
8 hour duration (480). Depending on the selected duration, the installer must cover the
default 1 hour (60) printing with one label that has the required duration. Please take notice
of the orientation of the label.
3
Power & Communication Connections
Pass the mains cable through the hole and connect
them to the terminal blocks. L for live wire N for
From the
neutral. The ground terminal is for termination
Panel
purposes only. To connect the luminaire with the
addressable panel, pass the 2 signal cables and
connect them on the C1 and C2 terminals, minding
the correct polarity. Set the luminaire address via
the dip switch. For the different address dip switch
settings, see the extra leaflet.
N for Neutral, L for Live wire
Dip Switch Settings
4
3
Figure
1 2 3 4 1 2 3 4
3h 8h
B-C2
A-C1
N
L
923796000_09_001