Savant PAV-VIMVP1F2 Series Quick Reference Manual

Savant® IP Video Single Input Transmitter 4K UHD with Video Processing and Control
(PAV-VIMVP1F2/PAV-VIMVP1CP2)
Quick Reference Guide

Box Contents

(1) IP Video Transmitter (PAV-VIMVP1F2-xx/PAV-VIMVP1CP2-xx)
(1) SFP+ module (PAV-VIMVP1F2-xx only)
(1) Installation Kit (075-0210-xx)
(1) Power Adapter with International Clips (025-0195-xx)
(1) International Clips (CN, US, UK, EU & AUS)
(2) Mounting Brackets (071-1093-xx)
(4) M2.5 x 4mm screws (for mounting brackets) (039-0590-xx)
(1) IR Emitter (4ft long) (064-0442-xx)
(1) 3-pin RS232 Control Connector (028-0805-xx)
(1) Product Regulatory Statement (009-1950-xx)

Specifications

Environmental

Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)

Dimensions and Weights

Height
0.98 in
Device
(2.50 cm)
4.0 in
Shipping
(10.16 cm)
Rack Space 1U

Power

12V 3A DC
Input Power
PoE+ (IEEE 802.3at)
16 W (PAV-VIMVP1F2-xx)
Nominal Power
19 W (PAV-VIMVP1CP2-xx)
36 W (PAV-VIMVP1F2-xx)
Maximum Power
36 W (PAV-VIMVP1CP2-xx)

Compliance

FCC Part 15
Safety and
Emissions
RoHS Compliant

Supported Releases

Software Release da Vinci

Supported Audio and Video Formats

Audio
Supported Pass-though of all HDMI audio formats are
Formats supported.
Video
HDR Supported
Dolby® Vision Supported
5
640x480 1280x720
5
720x480 1280x720
Supported
4
720x576 1280x1024
Formats
5
800x600 1920x1080
5
1024X768 1920x1080
1 = at 24 Hz 3 = at 30 Hz
2 = at 25 Hz 4 = at 50 Hz
PAV-VIMVP1F2-xx/PAV-VIMVP1CP2-xx QRG | 009-2059-00
Copyright 2022 Savant Systems, Inc | 220121
Width Depth Weight
8.46 in 5.51 in 1.65lb
(21.50 cm) (13.99 cm) (0.75 kg)
9.0 in 16.0 in 4.8lb
(22.86 cm) (40.64 cm) (2.17 kg)
CE C-Tick
9.4.3 and higher
4 4
1920x1080 3840x2160
5 5
1920x1080 3840x2160
5 5
1920x1200 3840x2160
1 1
3840x2160 4096x2160
3 2
3840x2160 4096x2160
5 = at 60 Hz

Required Components

– Savant IP Video Receiver
– Savant System Host
– Savant qualified 10G Managed Network Switch
– Savant User Interface
– Savant Development Environment (SDE) and Configuration Tools

Front Panel

A B C D
Power Status Video LinkTx
Item
A
Power LED
B
Status LED
C
Video LED
D
Link TX LED
E
Link RX LED
F
USB
UKCA G
System LED
H
USB Host
I
USB HID
J
P1

Networking Guidelines

To ensure that the IP Address will not change due to a power outage,
Savant recommends using DHCP reservation within the router. By
using this method IP Addresses for all devices can be managed from a
single UI, avoiding the need to access devices individually.
NOTE: IP video device requirements and how to manage IP address-
es are available on the Savant Device Netwoking Guidelines on the
3
Savant Customer Community.
4
Additional Information
5
Refer to the following documents located on the Savant Customer
Community for additional information.
3
– Savant IP Video Deployment Guide (009-1977-xx)
5
– Savant IP Video Network Configuration Guide (009-1552-xx)
– Savant IP Audio Deployment Guide (009-1571-xx)
– Savant Device Networking Guidelines
1 of 2
E F G
LinkRx USB System USB HOST USB HID
H I
Description
Off - Device is off. No power applied.
Red - Main board is powered.
Blue - Reset button is pressed when the
device is powered on.
Blinking - Reset button has been released or
the device was powered on without holding
the reset button.
Off - No video signal detected.
Blue - Video signal detected.
Off - No valid connection
Blue - Valid link
Blinking - Sending Ethernet Data
Off - No valid connection
Blue - Valid link
Blinking - Receiving Ethernet Data
Reserved for future use.
Not used and will remain in the OFF state.
Reserved for future use.
Reserved for future use.
Reserved for future use.
45 Perseverance Way, Hyannis, MA 02601
Savant.com
P1
J
| 508.683.2500