Compound Cutting - Makita DLS713NZ Instruction Manual

come to rest against the blade. If the blade is raised
while it is rotating the cut-off piece maybe ejected by the
blade causing the material to fragment which may result
in serious personal injury.
NOTICE:
When pressing down the handle, apply pressure in
•
parallel with the blade.
perpendicularly to the turn base or if the pressure
direction is changed during a cut, the precision of
the cut will be impaired.
5.

Compound cutting

Compound cutting is the process in which a bevel
angle is made at the same time in which a miter
angle is being cut on a workpiece. Compound
cutting can be performed at the angle shown in the
table.
Miter angle
Left and Right 45
Right 50
Right 55
Right 57
006393
When performing compound cutting, refer to "Press
cutting", "Slide cutting", "Miter cutting" and "Bevel
cut" explanations.
6. Cutting crown and cove moldings
Crown and cove moldings can be cut on a
compound miter saw with the moldings laid flat on
the turn base.
1 2
001555
There are two common types of crown moldings
and one type of cove moldings; 52/38° wall angle
crown molding, 45° wall angle crown molding and
45° wall angle cove molding. See illustrations.
(1) (2) (3) (4)
1 2
Fig.A
001556
If a force is applied
Bevel angle
Left 0 - 45
Left 0 - 40
Left 0 - 30
Left 0 - 25
1. 52/38 ﾟ type
crown molding
2. 45 ﾟ type crown
molding
3. 45 ﾟ type cove
molding
3
1. Inside corner
2. Outside corner
1
(1)
(4)
(2)
(3)
(1)
(2)
(1)
001557
There are crown and cove molding joints which are
made to fit "Inside" 90° corners ((1) and (2) in Fig.
A) and "Outside" 90° corners ((3) and (4) in Fig. A).
Measuring
Measure the wall length and adjust workpiece on
table to cut wall contact edge to desired length.
Always make sure that cut workpiece length at the
back of the workpiece is the same as wall length.
Adjust cut length for angle of cut. Always use
several pieces for test cuts to check the saw
angles.
When cutting crown and cove moldings, set the bevel
angle and miter angle as indicated in the table (A) and
position the moldings on the top surface of the saw base
as indicated in the table (B).
In the case of left bevel cut
Molding
position in
Fig. A
(1)
For inside
corner
(2)
(3)
For outside
corner
(4)
006361
Molding
position in
Fig. A
(1)
For inside
corner
(2)
For
(3)
outside
corner
(4)
006362
Example:
In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
Tilt and secure bevel angle setting to
•
33.9° LEFT.
Adjust and secure miter angle setting to
•
31.6° RIGHT.
15
1. Inside corner
2. Outside corner
(1)
(2)
(2)
2
(1)
(2)
Table (A)
Bevel angle
52/38° type 45° type 52/38° type
Right 31.6°
Left 33.9° Left 30° Left 31.6°
Right 31.6°
Table (B)
Molding edge against
guide fence
Ceiling contact edge should
be against guide fence.
Wall contact edge should be
against guide fence.
Ceiling contact edge should
be against guide fence.
Miter angle
45° type
Right 35.3°
Left 35.3°
Right 35.3°
Finished piece
Finished piece
will be on the
Left side of
blade.
Finished piece
will be on the
Right side of
blade.