Ideal Heating LOGIC COMBI2 C24 User Manual
  1. Manuals
  2. Brands
  3. Ideal Heating Manuals
  4. Boiler
  5. LOGIC COMBI2 C24
  6. User manual

Ideal Heating LOGIC COMBI2 C24 User Manual

Hide thumbs Also See for LOGIC COMBI2 C24:

Advertisement

Table of Contents

USER GUIDE
LOGIC COMBI
2
C24 C30 C35
When replacing any part on this appliance, use only spare parts that you can be assured conform to the safety and performance
specification that we require. Do not use reconditioned or copy parts that have not been clearly authorised by Ideal Heating.
For the very latest copy of literature for specification and maintenance practices visit our website idealheating.com
where you can download the relevant information in PDF format.
October 2022
User Guide
3
UIN 228296 A06

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LOGIC COMBI2 C24 and is the answer not in the manual?

Questions and answers

penny Weightman
March 6, 2025

When setting the start time for heating to come on how do you enter time for it to go off

0

Subscribe to Our Youtube Channel

Related Manuals for Ideal Heating LOGIC COMBI2 C24

Summary of Contents for Ideal Heating LOGIC COMBI2 C24

  • Page 1 When replacing any part on this appliance, use only spare parts that you can be assured conform to the safety and performance specification that we require. Do not use reconditioned or copy parts that have not been clearly authorised by Ideal Heating.
  • Page 2 Benchmark Commissioning Checklist. You can check your installer by calling Gas Safe Register direct on 0800 4085500. Ideal Heating is a member of the Benchmark scheme and fully supports the aims of the programme. Benchmark has been introduced to improve the standards of installation and commissioning of central heating systems in the UK and to encourage the regular servicing of all central heating systems to ensure safety and efficiency.

  • Page 3: Table Of Contents

    CONTENTS 1.1 Introduction ..............3 1.6 General Information ............7 1.2 Boiler Operation ............4-5 1.7 Troubleshooting .............. 8 1.3 System Water Pressure ..........6 1.8 Normal Operation Display Codes ........8 1.4 Points for the boiler user ..........6 1.9 Fault Codes ..............

  • Page 4: Boiler Operation

    BOILER OPERATION Legend A. Domestic Hot Water Temperature Knob B. Central Heating Temperature Knob C. Mode Button D. Boiler Status Display E. Burner On indicator F. Restart Button G. Pressure Gauge To START the boiler Boiler is active for Domestic Hot Water If a programmer is fitted refer to separate instructions for the programmer before continuing.
  • Page 5 OPERATION MODES CENTRAL HEATING The boiler controls the central heating radiator temperature WINTER CONDITIONS - (CENTRAL HEATING AND to a maximum of 80 C, adjustable via the central heating DOMESTIC HOT WATER REQUIRED) temperature knob (B). Press the mode button until there is not a cross through the Approximate temperatures for central heating: radiator symbol.

  • Page 6: System Water Pressure

    SYSTEM WATER PRESSURE 2 bar The system pressure gauge (see page 4) indicates the central heating system pressure. If the pressure is seen to fall below the original installation pressure of 1-2 bar over a period of time and continue to fall then a water leak may be indicated. In this event re-pressurise the 1 bar system as shown below.

  • Page 7: Condensate Drain (Unblocking)

    UNBLOCKING THE CONDENSATE DRAIN GENERAL INFORMATION This appliance is fitted with a siphonic condensate trap system BOILER PUMP that reduces the risk of the appliance condensate from freezing. The boiler pump will operate briefly as a self-check once every However should the condensate pipe to this appliance freeze, 24 hours, regardless of system demand.

  • Page 8: Troubleshooting

    TROUBLESHOOTING NO HOT WATER OR CENTRAL NO HOT WATER NO CENTRAL HEATING HEATING Check the mains power is Check that the mains power is Check that the mains power is switched on and that there is turned on and that there is not turned on and that there is not a no a cross through the radiator a cross through the radiator...

  • Page 9: Fault Codes

    FAULT CODES DESCRIPTION ACTION DISPLAY CODE ON BOILER Check system water pressure is between 1 & 1.5bar on the system pressure gauge. To Low Water Pressure F 01 re-pressurise the system see Section 3. If the boiler still fails to operate then please contact Ideal (if under warranty) or alternatively a Gas Safe Registered Engineer if outside of the warranty period.
  • Page 10 At Ideal Heating we take our environmental impact seriously, therefore when installing any Ideal Heating product please make sure to dispose of any previous appliance in an environmentally conscious manner. Households can contact their local authority to find out how.

This manual is also suitable for:

Logic combi2 c30Logic combi2 c35

Table of Contents

Save PDF