Related Manuals for Ruckus Wireless ZoneDirector 1100
Summary of Contents for Ruckus Wireless ZoneDirector 1100
- Page 1 VIEW Certified Configuration Guide Ruckus Wireless ZoneDirector 1100, 3000, 5000 with ZoneFlex™ 7363, 7372, 7982 721-1004-000 Rev: E August 2014...
- Page 2 VIEW Certified Configuration Guide: Ruckus Wireless Copyright Notice © 2012-2014 Spectralink Corporation All rights reserved. Spectralink , the Spectralink logo and the names and marks associated with Spectralink’s products are trademarks and/or service marks of Spectralink Corporation and are common law marks in the United States and various other countries. All other trademarks are property of their respective owners.
-
Page 3: Table Of Contents
Contents Chapter 1: Introduction ............4 Certified Product Summary ....................4 Known Limitations ......................5 Spectralink References ....................5 Support Documents ......................6 White Papers ........................7 Product Support ....................... 7 Chapter 2: Overview ............8 Network Topology......................8 Chapter 3: Getting Started ............ 9 Out of the Box Configuration of ZoneDirector .............. -
Page 4: Chapter 1: Introduction
The products listed below have been tested in Spectralink’s lab and have passed VIEW Certification. This document details how to configure Ruckus® controllers ZoneDirector (ZD) 1100/3000/5000 and Ruckus Access Points ZoneFlex™ (ZF) 7363/7982 with Spectralink Wireless Telephones. Certified Product Summary Manufacturer: Ruckus Wireless; www.ruckuswireless.com Certified products: Controllers: APs: ZD1100... -
Page 5: Known Limitations
VIEW Certified Configuration Guide: Ruckus Wireless Handset* models tested: Spectralink 8020/8030 Handset radio mode: 802.11b/g/n 802.11a/n Meets VIEW minimum call capacity per 6 with Wi-Fi Std QoS 8 with Wi-Fi Std QoS AP:** * Spectralink handset models and their OEM derivatives are verified compatible with the WLAN hardware and software identified in the table. -
Page 6: Support Documents
VIEW Certified Configuration Guide: Ruckus Wireless To go to a specific product page: Select the Product Category and Product Type from the dropdown lists and then select the product from the next page. All resources for that particular product are displayed by default under the All tab. -
Page 7: White Papers
VIEW Certified Configuration Guide: Ruckus Wireless The Spectralink 84-Series Wireless Telephone Administration Guide provides a comprehensive list of every parameter available on Spectralink 84-Series Wireless Telephones. The Spectralink 84-Series Deployment Guide is your essential reference for provisioning and deploying Spectralink 84-Series handsets in any environment. -
Page 8: Chapter 2: Overview
Chapter 2: Overview Spectralink 8020/8030 handsets can be configured with Wi-Fi Standard QoS. On the Admin menu navigate to Network Config> WLAN settings> Custom> QoS> . Spectralink 84- and 87-Series handsets only support Wi-Fi Standard QoS. Network Topology Note: Example configuration shown This configuration is not applicable to all customer environments. -
Page 9: Chapter 3: Getting Started
Chapter 3: Getting Started Out of the Box Configuration of ZoneDirector When Ruckus Wireless gear is unpacked, the first piece of equipment that needs to be configured is the ZoneDirector. The goal of the initial setup is to give the ZoneDirector a name and to assign an IP address or tell it to use DHCP. -
Page 10: Software Upgrade
VIEW Certified Configuration Guide: Ruckus Wireless The default Admin name is admin. The default Password is admin. Tthe dashboard screen appears. Use the menu bar at the top of the screen to navigate to the three options: Monitor, Configure and Administer. -
Page 11: View/Configure System Settings
VIEW Certified Configuration Guide: Ruckus Wireless View/Configure System Settings Navigate to Configure> System. System is where basic information about the ZD can be entered. 721-1004-000-E.docx August 2014... -
Page 12: Chapter 4: General Settings
Chapter 4: General Settings RADIUS Server Definition Configuring a WLAN with WPA2-Enterprise scheme requires configuration of a RADIUS server. How to setup and configure an external radius server is not discussed in this document. However, configure a radius server details within ZD so that ZD can communication with external server as follows Navigate to Configure>... -
Page 13: Configure Services
VIEW Certified Configuration Guide: Ruckus Wireless Configure Services The handsets are not compatible with the automatic channel optimization provided by the ChannelFly Self Healing method or Background Scanning. No testing was performed with tunnel configuration enabled. Configure Admission Control Call admission control can be configured at different places in a ZD depending on what level of call admission control is required. -
Page 14: Qos Configuration
VIEW Certified Configuration Guide: Ruckus Wireless Per AP -> Bandwidth limits for the whole of the AP are defined here. This applies to all WLANs configured in the AP for which CAC is enforced Per AP group -> Denotes CAC for member APs defined in a AP group and all WLANs configured in the AP. - Page 15 VIEW Certified Configuration Guide: Ruckus Wireless DSCP DSCP DSCP TOS String Class (hex) (dec) (hex) Prec. Delay Throghput Reliability Format (dec) Flag Flag Flag 0×20 0×80 FlashOverride af41 0×22 0×88 FlashOverride af42 0×34 0×90 FlashOverride af43 0×26 0×98 FlashOverride 0×28...
- Page 16 VIEW Certified Configuration Guide: Ruckus Wireless The settings must be reconciled between the handsets and the infrastructure. The settings on other devices such as a PBX or SIP server and network routers, must be taken into consideration. To change the settings in the Ruckus controller, use the CLI interface by using the ssh protocol with the IP address of the controller and using the administrative login.
- Page 17 VIEW Certified Configuration Guide: Ruckus Wireless Press OK. To change settings in the 84-Series handsets, there are two methods: Method 1: Use the Web Configuration Utility on a handset-by-handset basis. Open the Web Configuration Utility and navigate to Settings> Network> QoS.
- Page 18 VIEW Certified Configuration Guide: Ruckus Wireless Enter the DSCP value in decimal or as a hex number in the form 0x2e. Enter a value for Call control DSCP in decimal or as a hex number in the form 0x28. 721-1004-000-E.docx...
-
Page 19: Chapter 5: Wlan Configuration
Chapter 5: WLAN Configuration This section describes how various WLANs can be configured. Configure Security Settings For any security option, you will first name and describe the configuration. Then you will select the security type and complete the required information for that type. Security: Open Navigate to Configure>... -
Page 20: Security: Wpa-Psk
VIEW Certified Configuration Guide: Ruckus Wireless Security: WPA-PSK Navigate to Configure> WLAN> Create New. Enter the required values for Name, ESSID, Description and Type. Select Open under Authentication Options Method. Select WPA for Encryption Options Method. Choose Auto for Encryption Options Algorithm. - Page 21 VIEW Certified Configuration Guide: Ruckus Wireless 721-1004-000-E.docx August 2014...
-
Page 22: Security: Wpa2-Psk
VIEW Certified Configuration Guide: Ruckus Wireless Security: WPA2-PSK Navigate to Configure> WLAN> Create New. Enter the Name, ESSID, Description and Type. Select Open under Authentication Options Method. Select WPA for Encryption Options Method. Select AES for Encryption Options Algorithm. Enter [your passphrase] in the Passphrase text box. -
Page 23: Security: Wpa2-Enterprise
VIEW Certified Configuration Guide: Ruckus Wireless Security: WPA2-Enterprise After definining a RADIUS server as described in RADIUS Server Definition, follow the steps below to create a WLAN with WPA2-Enterprise scheme Navigate to Configure> WLAN> Create New. Enter the values for Name, ESSID, Description and Type. -
Page 24: Advanced Options On The Wlan
VIEW Certified Configuration Guide: Ruckus Wireless Advanced Options on the WLAN After setting the Security option, additional WLAN options can be configured. At the bottom of the Security window is the Advanced Options hyperlink. Click it to open the Advanced Options window. - Page 25 VIEW Certified Configuration Guide: Ruckus Wireless 721-1004-000-E.docx August 2014...
-
Page 26: Wlan Settings From The Cli
AdminTip: Repeat when new APs added These commands must be re-issued when a new AP is powered up and added to the network. Welcome to the Ruckus Wireless ZoneDirector 1100 Command Line Interface ruckus> enable ruckus# debug ruckus(debug)# rksap_cli -A "set dtim-period wlan0 2”... -
Page 27: Chapter 6: Ap Configuration
Chapter 6: AP Configuration AP Group Setup Call Admission Control (CAC) can be configured for an AP group instead of configuring at individual AP. However, configuration at individual AP radio supersedes the configuration at AP group. This configuration ensures all configured APs in the AP group to have same CAC setting instead of configuring CAC for individual APs. -
Page 28: Individual Ap Configuration
VIEW Certified Configuration Guide: Ruckus Wireless AdminTip: 8020/8030 handsets are not 802.11n devices 8020/8030 handsets will not be admitted to a network with 11N only Mode set to N- only. Individual AP Configuration At the AP level, CAC is configured per radio. The airtime % denotes the percentage of total available BW that shall be reserved for voice/video class. - Page 29 VIEW Certified Configuration Guide: Ruckus Wireless AdminTip: 87-Series (PIVOT) does not support CAC CAC must not be enabled on an SSID that 87-Series will use to connect. The feature is scheduled for future implementation. Click Configure> Access Points and click Edit for the AP where CAC is required.
- Page 30 VIEW Certified Configuration Guide: Ruckus Wireless 721-1004-000-E.docx August 2014...