Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Crystal Vision HDDA104R
Summary of Contents for Crystal Vision HDDA104R
- Page 1 HDDA104R and HDDA108R HD/SDI Distribution Amplifiers Crystal Vision Ltd., Lion Technology Park, Station Road East, Whittlesford, Cambridge, CB22 4WL, England. E-mail: sales@crystalvision.tv Website: www.crystalvision.tv Tel: +44(0) 1223 497049 Fax: +44(0) 1223 497059...
-
Page 2: Table Of Contents
Crystal Vision HDDA104R/108R User Manual R1.2 Contents Introduction Hardware installation Universal rear connectors Rear module connections with RM34 General purpose interface 4U frame GPI connections 2U frame GPI Connections 1U frame GPI connections ... -
Page 3: Introduction
HD/SD and PSU status when opened. HDDA104R/108R multi-standard distribution amplifiers The HDDA family consists of two models. The basic model is the HDDA104R one input to four outputs reclocking DA. The addition of a four output sub PCB increases the total number of outputs to eight creating the HDDA108R. -
Page 4: Hardware Installation
2.1 Universal rear connectors The HDDA104R uses a single-height rear connector, this will allow the 4U Indigo frame to house up to 24 modules and three power supplies. The 2U Indigo 2 frame will house 12 modules and dual power supplies. The 1U Indigo 1 will house six modules with a single power supply. -
Page 5: General Purpose Interface
LED directly. If the series resistor is shorted out, it can drive a bulb at +45V 500mA max. The +5V output is protected by self-resetting thermal fuses, which limit the total output Note: current available from Remotes 1-4 to approximately 1A. Remotes 5-8 are similarly protected. HDDA104R/108R User Manual R1.2 21/04/2008... -
Page 6: Frame Gpi Connections
Remote 2, Remote 4, Remote 6 and Remote 8 are 26 way high-density D-Type male plugs and frame ground is pin 6 in each case and +5V @500mA is pin 15 on Remote 2 and Remote 6. HDDA104R/108R User Manual R1.2 21/04/2008... -
Page 7: Frame Gpi Connections
Remote 1: 26 way high density D-type socket. Frame ground is pin 2 and +5V @500mA Note: is pin 1. Remote 2: 26 way high density D-type plug. Frame ground is pin 6 and +5V @500mA is pin 15. HDDA104R/108R User Manual R1.2 21/04/2008... -
Page 8: Indigo Dt Desk Top Box Gpi Connections
Remote 2: 26 way high-density D-Type male plugs and frame ground is pin 6 and +5V @500mA is pin 15 Note. The +5V output is protected by self-resetting thermal fuses, which limit the total output current available from Remotes 1-2 to approximately 1A. HDDA104R/108R User Manual R1.2 21/04/2008... -
Page 9: Card Edge Operation
Crystal Vision Card edge operation 3 Card edge operation HDDA104R/HDDA108R The front card-edge of the HDDA104R/HDDA108R provides power rail monitoring and signal status. HDDA104R front edge view Name Function when ON Function when Off Colour One or more of the monitor Green Good power supply (PSU) rails. -
Page 10: Using The Active Front Panel
Note: passwords cleared prior to using the panel for the first time. At power up, the two-line, 20-character screen will display ‘Crystal Vision’ followed by the firmware version number for the control panel. All eight control panel keys LEDs will illuminate. - Page 11 Device menu • Rotary control – shaft encoder used to select options or variable data Please refer to the Crystal Vision Control Panel manual for details of the Panel Setup, Note: Lock Panel and Diagnostic menus. Selecting an HDDA104R/108R To select a particular card in a frame, press the DEVICE key to go to the Device menu.
-
Page 12: The Hdda104R/108R Menu Structure
CAL to update the display. The HDDA104R/108R menu structure Pressing ENTER once the HDDA104R/108R has been selected in the cards available menu will display the home menu. The information displayed will be: the card type and its software version, its position in the rack and the input video standard. This is the only menu available to the HDDA104R/108R. -
Page 13: Statesman
Statesman 4 Statesman The Crystal Vision Statesman PC control software is designed to control a range of Crystal Vision modules via serial control from a PC. Statesman provides a user friendly means of configuring and operating Crystal Vision modules with the benefit of “see-at-a- glance”... -
Page 14: Video Properties
720 Prg 59.94 1080 Int 60 720 Prg 60 1080 Int 50 1080 Int 59.94 1080 Prg 29.97 1080 Prg 24.98 1080 Prg 30 1080 Prg 25 1080 Prg 24 1080 sF 23.98 1080 sF 24 HDDA104R/108R User Manual R1.2 21/04/2008... -
Page 15: Trouble Shooting
There is no video output Check that a valid video input is present (input present LED illuminated) and that any cabling is intact The video output is low quality Check that the maximum length has not been exceeded HDDA104R/108R User Manual R1.2 21/04/2008... -
Page 16: Specification
Four off HD or SD SDI 270Mb/s to 1.485Gb/s serial digital compliant to SMPTE-259M and SMPTE-292M HDDA108R Eight off HD or SD SDI 270Mb/s to 1.485Gb/s serial digital compliant to SMPTE-259M and SMPTE-292M RS485, 19200 baud, Statesman PC Remote control HDDA104R/108R User Manual R1.2 21/04/2008...
Need help?
Do you have a question about the HDDA104R and is the answer not in the manual?
Questions and answers