Cleaning The Machine - Raider PRO RDP-SEBV20 SOLO User Manual

18 www.raider.bg
(Fig.18):
1. On/Оff switch
To start the tool, slide the switch to the "I (ON)"
position.
To stop the tool, slide the switch to the "O
(OFF)" position.
NOTE: If the machine has been running
continuously until the battery is exhausted,
leave the machine for at least 15 minutes before
working with a new battery.
NOTE: When you start sliding the switch,
electronic sound may be output from the
machine, but this does not indicate a
malfunction of the machine.
9. Speed adjustment
(Fig.19):
1. Speed regulator
The speed can be changed by turning the
speed control knob to a set digital setting from
1 to 6. A higher speed is obtained when the
controller is turned in the direction of number 6.
And a lower speed is obtained when turning in
the direction of number 1.
NOTE: The dial cannot be rotated directly from
1 to 6 or from 6 to 1. This may damage the
knob. When changing the dialing direction,
always turn the knob by moving it through each
intermediate number. See the table for the
relationship between the dial number settings
and the speed.
NUMBER SPEED
5~6 High
3~4 Medium
1~2 Low
10. Work
CAUTION: Do not place the machine on the
ground while it is turned on. Sand or dust
can enter from the suction port and cause a
malfunction or injury.
When blowing:
CAUTION: When working with a blower, be sure
to remove the dust bag and suction tube from
the machine and insert the blower nozzle.
Hold the machine firmly with your hand and
perform the blow operation by moving it slowly.
When blowing around a building, large rock,
or vehicle, direct the nozzle away from them.
When performing a corner operation, start from
the corner and then move to a wide area.
When sucking:
CAUTION: When performing suction with the
appliance, be sure to attach the dust bag and
suction tube in place to the machine.
CAUTION: Check the dust bag frequently for
wear or damage.
CAUTION: Be sure to secure the dust bag
fastener before operating the machine.
CAUTION: Always turn off the machine before
opening or attaching the dustbag clasp.
NOTE: Do not allow wet materials, such as
wet sheets and foreign materials, such as
large sawdust, metals, glass, pebbles, etc.,
to be sucked into the machine. Otherwise, a
malfunction may occur.
NOTE: Empty the bag before filling. Otherwise,
a malfunction may occur.
Hold the machine firmly. It is equipped with
both a main soft handle and a front auxiliary
handle. Use both to get the best grip on the
tool. While working with the machine, adjust
the speed so that the suction power is suitable
for the workplace and conditions. As shown
in the figure, you can use the wheels to move
the machine for easy and efficient operation.
(Fig.20):
1. Additional handle;
2. Main handle.
NOTE: Do not cover the vents during operation
or this may cause the tool to overheat and be
damaged.
(Fig.21):
1. Ventilation openings
Empty the collection bag before it is filled by
removing it from the machine and then open the
zipper to clean it (Fig. 22):
1. Zip
CAUTION: Always make sure the machine
is turned off and without a battery before
attempting to perform inspection or
maintenance.

11. Cleaning the machine.

Clean the machine by wiping the dust with a
dry cloth or one dipped in soapy water and
squeezed.
NOTE: Never use gasoline, thinner, alcohol.
Discoloration, deformation or cracking may
occur. Remove dust or dirt from the suction
openings (Fig. 23):
1. Suction opening
Heavily soiled collecting bag
can be washed with soap and water.Maintain
the protective mechanisms,
air vents and engine box
as clean as possible from dust and dirt.
Clean the appliance with a clean cloth or
blow with compressed air below low
pressure.
We recommend that you clean the appliance
immediately after each use.
Clean the appliance regularly with a damp cloth
and a little mild soap. Do not use
detergents or solvents; they would